Hitachi 55HDX61A HOW to USE the Remote To Control VCR/PVR Functions, Precoded VCR/PVR Buttons

Page 47

HOW TO USE THE REMOTE

TO CONTROL VCR/PVR FUNCTIONS

Operating the precoded function for your VCR/PVR (Personal Video Recorder).

This remote is designed to operate different types of VCRs/PVRs. You must first program the remote to match the remote system of your VCR/PVR (refer to pages 51-52 for pre-codes).

1.Turn ON your VCR/PVR.

2.Aim the remote control at the front of your VCR/PVR.

3. To switch to VCR/PVR pre-coded mode, use the SOURCE ACCESS buttons ( , ) on the remote control to position the LED light to the corresponding selection.

4.Hold down the ENT button on the remote and enter the four digit preset code that matches your VCR/PVR, as shown on pages 51- 52. Release the ENT button. The indicator light will flash 3 times if the code was accepted.

5.Aim the remote at the VCR/PVR and press the POWER button. The remote will turn off your PVR when the correct four digit preset code is entered. When this occurs, the remote control is programmed for your VCR/PVR. If the VCR/PVR does not turn off, try a different four digit preset code.

6.The remote will now control your VCR/PVR.

NOTES:

1.If your PVR cannot be operated after performing the above procedures, your PVR’s code has not been precoded into the remote.

2.In the unlikely event that your PVR cannot be operated after performing the above procedures, please consult your PVR operating guide.

3.The remote control will remember the codes you have programmed until the batteries are removed from the remote control. After replacing the batteries repeat the entire programming procedure as stated above.

4.VCR precode library is included in the PVR mode. Default device for this mode is Hitachi VCR.

5.INFO, GUIDE and LC (Last Channel) buttons are for PVR devices, not for VCR.

PRECODED VCR/PVR Buttons

These buttons transmit the chosen precoded VCR/PVR codes.

EXCLUSIVE TV Buttons

These buttons are for operating the TV.

A/V NET

GUIDE

THE REMOTE CONTROL

MY VCR/PVR CODE IS:

NOTE: Refer to instruction manual of the VCR/PVR for operation of the buttons exclusively for the VCR/PVR.

47

Image 47

Contents Operating Guide for 55HDX61A Do not Open Important Safety InstructionsPublic Viewing of Copyrighted Material Read before operating equipmentPrevention of Screen Burn First AccessoriesUSE Time Antenna HOW to Setup Your NEW Hitachi Plasma TelevisionFirst Time USE Securing to a wallVertical Viewing HOW to SET UP Your NEW Hitachi Plasma TelevisionViewing BestHookup Cables First Time Antenna Connections to Rear Panel JacksUSE Photo Input Front Panel ControlsPhones Jack Monitor OUT Rear Panel JacksRGB Audio Input Upgrade CardTo Power Swivel Connector RGB Analog InputRear Panel of AVC CableCARD SlotConnecting External Video Sources Connecting Plasma Display Monitor to AVC BOXBefore Operating External Video Source Connecting a Monaural Audio Source to INPUT1~INPUT5Connecting a Stereo VCR or Stereo Laserdisc Player Connecting S-VIDEO VCR or Laserdisc Player DVI to Hdmi Input Hdmi inputSee page 27 for tips on Rear Panel Connections Digital VCR D-VHS Connecting External Audio Amplifier Connecting External AUDIO/VIDEO DevicesConnecting AV Network Setup Procedure Using AV Network Device Codes AV Network Setup WizardSpeakers to on or OFF, then press Select to set Remote controlUse the Cursor Pads To choose AV Receiver To select Internal SpeakersAUDIO/VIDEO Codes for AV Network not for remote control Time USE Rear Panel ConnectionsTips on Rear Panel Connections Remote Control Remote ControlHOW to USE the Remote To Control Your Plasma TV 480P Input RGB Analog Input Aspect Display ModeAspect button RatioGuide button DAY/NIGHT buttonPICTURE-IN-PICTURE button Menu buttonAV NET button ControlRemote AV NET Learning Wizard Select OK Softkeys. If the device responds, then it is properly set upIeee Inputs buttonPhoto Input Ant B Ant a Select this menu item to view the chosen picture number JumpRotate SlideshowWhen an IEEE1394 device is connected Video When an S-VIDEOInfo button Last Channel LC button Volume VOL WHEEL, Mute buttonChannel CH WHEEL/CHANNEL Selector buttons Dash buttonPIP button POP Mode PICTURE-IN-PICTUREPress the Cursor PAD or to enable the sub-picture sound PICTURE-IN-PICTURE PIPNtsc PIP Mode PICTURE-IN-PICTURESplit Mode PICTURE-IN-PICTURE Surf Mode PICTURE-IN-PICTUREStrobe Freeze Main FreezeSplit Freeze Exclusive TV buttons HOW to USE the Remote To Control Cable BOX FunctionsOperating the precoded function for your cable box Precoded Cable BOX buttonsPRE-CODED SET-TOP-BOX/SATELLITE Receiver buttons These buttons transmit the chosen precoded DVD codes HOW to USE the Remote To Control DVD FunctionsOperating the precoded function for your DVD player Precoded DVD ButtonsThese buttons transmit the chosen precoded VCR/PVR codes HOW to USE the Remote To Control VCR/PVR FunctionsPrecoded VCR/PVR Buttons Precoded Audio Buttons HOW to USE the Remote To Control Additional Audio EquipmentOperating the precoded function for your Audio component Input Access Remote VCR Brand Audio Brand ON-SCREEN Display OSD On-Screen DisplayFor Video AudioChannel Manager Locks Timers Setup Power Swivel Display Picture ModeVideo Contrast Noise Reduction Reset Video SettingsWhite Balance ON-SCREENColor Management Color DecodingAudio DRC Language Digital OutputVertical Position AspectAspect Auto AspectPress Cursor PAD To highlight Ant a or Ant B Channel ManagerSet The Antenna Auto Channel ScanChannel List Signal MeterLocks Movie Ratings TV Ratings Canadian Ratings English Table Canadian Ratings EngProgramming restricted to adults Contains Canadian Ratings FrnCanadian Ratings French Table Programming is not suitable for childrenSet The Clock TimersSet Day/Night Timer Set Sleep TimerPlease Set Clock First Set Event TimerSet Timer Recording Menu Preference SetupScreen Saver Image PowerMenu Background Press Cursor PAD or Screen DisplaySet The Inputs Set Black Side Panel Channel Set Closed CaptionSet AV Control This feature will select the source of the Monitor OutputSet Monitor Out CableCARD InfoPower Swivel UpgradesSet Stand-By Mode RGB on Screen Display Using the RGB InputOperation No SYNC. Signal Invalid Scan Freq Aspect Setup Power Swivel Move SEL Sel Video Aspect Setup Power Swivel Brightness Color TemperatureInput ContrastAspect ResetEnhancer Position Using the RGBAuto Adjust Horizontal Clock Clock PhasePhase to factory preset, for current RGB format RGB Input UsingDo not Care of Your Hitachi Plasma Display Your Remote ControlIgnition Noise Reception ProblemsControl Useful Info SymptomsPicture Image Spectrum Useful InfoTrademark Acknowledgment Plug and PlayAgency Regulatory Information Outputs InputsHitachi Way Chula Vista, CA Home Electronics DivisionDigital Media Division 22-25 AccessoriesIndex TruBassOr the Software END User License Agreement for Hitachi DTV Software102 103 QR64291