Hitachi 55HDX61A HOW to USE the Remote To Control Additional Audio Equipment

Page 48

HOW TO USE THE REMOTE

TO CONTROL ADDITIONAL AUDIO EQUIPMENT

Operating the precoded function for your Audio component.

This remote is designed to operate different types of Audio component. You must first program the remote to match the remote system of your Audio component (refer to pages 51-52 for pre-codes).

1.Turn ON your Audio component you wish to control with the Remote.

2.Aim the remote control at the front of your Audio component.

3. To switch to Audio (AMP) component pre-coded mode, use the SOURCE ACCESS buttons ( or ) on the remote control to position the LED light to the corresponding selection.

CONTROL

4.Hold down the ENT button on the remote and enter the four digit preset code that matches your Audio component, as shown on pages 51-52. Release the ENT button. The indicator light will flash 3 times if the code was accepted.

5.Aim the remote at the Audio component and press the POWER button. The remote will turn off your Audio component when the correct four digit preset code is entered. When this occurs, the remote control is programmed for your Audio component. If the Audio component does not turn off, try a different four digit preset code.

6.The remote will now control your Audio component.

7.Repeat steps 1 - 6 if you wish to program the remote to control another Audio component.

THE REMOTE

NOTES:

1.If your Audio component cannot be operated after performing the above procedures, your Audio component’s code has not been precoded into the remote.

2.In the unlikely event that your Audio component cannot be operated after performing the above procedures, please consult your Audio equipment operating guide.

3.The remote control will remember the codes you have programmed until the batteries are removed from the remote control. After replacing the batteries repeat the entire programming procedure as stated above.

4.CD precode library is included in the AMP mode. Default device for this mode is Hitachi Audio/Video Receiver (AVR/AMP).

5.INPUT, GUIDE, Channel (up/down), Volume (up/down) and REC button are not for CD devices.

PRECODED AUDIO Buttons

These buttons transmit the chosen precoded Audio component codes.

EXCLUSIVE TV Buttons

These buttons are for operating the TV.

A/V NET

GUIDE

MY AUDIO EQUIPMENT CODE IS:

CD

AMP/RCVR

NOTES: 1. The REC (Record) button only applies to some precoded amplifier/receiver codes.

2.Refer to instruction manual of the Audio equipment for operation of the buttons exclusively for the Audio equipment.

48

Page 47 Page 49
Image 48
Page 47 Page 49
Contents Operating Guide for 55HDX61A Important Safety Instructions Do not OpenRead before operating equipment Prevention of Screen BurnPublic Viewing of Copyrighted Material Accessories USE TimeFirst HOW to Setup Your NEW Hitachi Plasma Television First Time USESecuring to a wall AntennaHOW to SET UP Your NEW Hitachi Plasma Television ViewingBest Vertical ViewingHookup Cables Antenna Connections to Rear Panel Jacks USEFirst Time Front Panel Controls Photo InputPhones Jack Rear Panel Jacks Monitor OUTUpgrade Card To Power Swivel ConnectorRGB Analog Input RGB Audio InputCableCARD Slot Rear Panel of AVCConnecting Plasma Display Monitor to AVC BOX Connecting External Video SourcesConnecting a Monaural Audio Source to INPUT1~INPUT5 Before Operating External Video SourceConnecting a Stereo VCR or Stereo Laserdisc Player Connecting S-VIDEO VCR or Laserdisc Player Hdmi input DVI to Hdmi InputSee page 27 for tips on Rear Panel Connections Digital VCR D-VHS Connecting External AUDIO/VIDEO Devices Connecting External Audio AmplifierConnecting AV Network AV Network Setup Wizard Setup Procedure Using AV Network Device CodesRemote control Use the Cursor Pads To choose AV ReceiverTo select Internal Speakers Speakers to on or OFF, then press Select to setAUDIO/VIDEO Codes for AV Network not for remote control Rear Panel Connections Time USETips on Rear Panel Connections Remote Control Remote ControlHOW to USE the Remote To Control Your Plasma TV RGB Analog Input Aspect Display Mode Aspect buttonRatio 480P InputDAY/NIGHT button PICTURE-IN-PICTURE buttonMenu button Guide buttonControl RemoteAV NET button AV NET Learning Wizard Softkeys. If the device responds, then it is properly set up Select OKInputs button Photo Input Ant B Ant aIeee Jump Select this menu item to view the chosen picture numberSlideshow RotateWhen an IEEE1394 device is connected When an S-VIDEO Info buttonVideo Volume VOL WHEEL, Mute button Channel CH WHEEL/CHANNEL Selector buttonsDash button Last Channel LC buttonPOP Mode PICTURE-IN-PICTURE Press the Cursor PAD or to enable the sub-picture soundPICTURE-IN-PICTURE PIP PIP buttonPIP Mode PICTURE-IN-PICTURE Split Mode PICTURE-IN-PICTURESurf Mode PICTURE-IN-PICTURE NtscMain Freeze Split FreezeStrobe Freeze HOW to USE the Remote To Control Cable BOX Functions Operating the precoded function for your cable boxPrecoded Cable BOX buttons Exclusive TV buttonsPRE-CODED SET-TOP-BOX/SATELLITE Receiver buttons HOW to USE the Remote To Control DVD Functions Operating the precoded function for your DVD playerPrecoded DVD Buttons These buttons transmit the chosen precoded DVD codesHOW to USE the Remote To Control VCR/PVR Functions Precoded VCR/PVR ButtonsThese buttons transmit the chosen precoded VCR/PVR codes HOW to USE the Remote To Control Additional Audio Equipment Operating the precoded function for your Audio componentPrecoded Audio Buttons Input Access Remote VCR Brand Audio Brand OSD On-Screen Display ON-SCREEN DisplayVideo Audio ForChannel Manager Locks Timers Setup Power Swivel Picture Mode VideoDisplay Contrast Reset Video Settings Noise ReductionON-SCREEN Color ManagementColor Decoding White BalanceAudio Language Digital Output DRCAspect AspectAuto Aspect Vertical PositionChannel Manager Set The AntennaAuto Channel Scan Press Cursor PAD To highlight Ant a or Ant BSignal Meter Channel ListLocks Movie Ratings TV Ratings Canadian Ratings Eng Canadian Ratings English TableCanadian Ratings Frn Canadian Ratings French TableProgramming is not suitable for children Programming restricted to adults ContainsTimers Set The ClockSet Sleep Timer Set Day/Night TimerSet Event Timer Please Set Clock FirstSet Timer Recording Setup Menu PreferenceImage Power Menu BackgroundScreen Saver Screen Display Set The InputsPress Cursor PAD or Set Black Side Panel Set Closed Caption ChannelThis feature will select the source of the Monitor Output Set Monitor OutCableCARD Info Set AV ControlUpgrades Set Stand-By ModePower Swivel Using the RGB Input RGB on Screen DisplayOperation No SYNC. Signal Invalid Scan Freq Aspect Setup Power Swivel Move SEL Sel Video Aspect Setup Power Swivel Color Temperature InputContrast BrightnessReset EnhancerAspect Using the RGB Auto AdjustPosition Clock Phase Phase to factory preset, for current RGB formatHorizontal Clock Using RGB InputCare of Your Hitachi Plasma Display Your Remote Control Do notReception Problems Ignition NoiseUseful Info Symptoms ControlUseful Info Picture Image SpectrumPlug and Play Trademark AcknowledgmentAgency Regulatory Information Inputs OutputsHome Electronics Division Hitachi Way Chula Vista, CADigital Media Division Accessories IndexTruBass 22-25END User License Agreement for Hitachi DTV Software Or the Software102 103 QR64291
Top Page Image Contents