Hitachi 55VG825 Remote Control for Additional Audio Equipment, Precoded Audio Buttons

Page 35

The Remote Control for Additional Audio Equipment

Operating the precoded function for your Audio component.

This remote is designed to operate different types of Audio component. You must first program the remote to match the remote system of your Audio component (refer to pages 37-38 for pre-codes).

1.Turn ON your Audio component you wish to control with the Remote.

2.Aim the remote control at the front of your Audio component.

3.To switch to Audio (AMP) component pre-coded

mode, use the SOURCE ACCESS buttons ( or ) on the remote control to position the LED light to the corresponding selection.

4.Hold down the ENT button on the remote and enter the four digit preset code that matches your Audio component, as shown on pages 37-38. Release the ENT button. The indicator light will flash 3 times if the code was accepted.

5.Aim the remote at the Audio component and press the POWER button. The remote will turn off your Audio component when the correct four digit preset code is entered. When this occurs, the remote control is programmed for your Audio component. If the Audio component does not turn off, try a different four digit preset code.

6.The remote will now control your Audio component.

7.Repeat steps 1 - 6 if you wish to program the remote to control another Audio component.

NOTE: 1. If your Audio component cannot be operated after performing the above procedures, your Audio component code has not been precoded into the remote.

2.In the unlikely event that your Audio component cannot be operated after performing the above procedures, please consult your Audio component operating guide.

3.The remote control will remember the codes you have programmed until the batteries are removed from the from the remote control. After replacing the batteries repeat the entire programming procedure as stated above.

PRECODED AUDIO Buttons

These buttons transmit the chosen precoded Audio component codes.

EXCLUSIVE TV Buttons

These buttons are for operating the TV.

/

MY AUDIO COMPONENT

CODE IS:

NOTE: Refer to instruction manual of the VCR/PVR for operation of the buttons exclusively for the VCR/PVR.

The Remote Control

35

Image 35

Contents LCD Rear Projection Television Read Before Operating Equipment Important Safety InstructionsLead Notice Power sourceModifications Public viewing of copyrighted materialFor U.S. models AccessoriesRemote Control Battery Installation and Replacement Viewing How to set up your new Hitachi Projection TelevisionAntenna LocationAntenna Connections to Rear Jack Panel Hook-up Cables and ConnectorsMode Indicator Quick Reference Remote Control Buttons and FunctionsSide Input Jacks Input Front Panel ControlsPhoto Input Power LightTemp Indicator Lamp IndicatorSide Panel Jacks and Connections Rear Panel Connections CableCARD Slot TV AS Center InputsIR Blaster/G-LINK VIDEO,Y-PBPRand Hdmi Tips on Rear Panel ConnectionsSpeaker placement Connecting External Audio SourcesBefore Operating External Video Source Connecting External Video SourcesConnecting a Composite Video Connecting a Component Source with Connecting a Component VCR Sensor Cable Box Automatic Mode Default mode Remote ControlSource Access ENT button How to Use the Remote to Control Your TVMode Indicator Source Access or buttonsZOOM1/ZOOM2 StandardExpanded AIR ANALOG/DIGITAL ChannelsCursor PAD Rotate How to Use the Remote to Control YourDash button Volume VOL WHEEL, Mute buttonLast Channel Last CH button Channel CH WHEEL/CHANNEL Selector buttonsPIP button POP Mode PICTURE-IN-PICTUREPicture-In-Picture PIP Surf Mode PICTURE-IN-PICTURE PIP Mode PICTURE-IN-PICTURESplit Mode PICTURE-IN-PICTURE Strobe Freeze Split FreezeMain Freeze Exclusive TV buttons Remote Control for Cable Box FunctionsOperating the precoded function for your cable box Precoded Cable BOX buttonsSET-TOP-BOX Code is Remote Control for Set-Top Box/Satelite Receiver FunctionsPRE-CODED SET-TOP-BOX/SATELLITE Receiver buttons MY Satellite ReceiverMY DVD Player Code is Remote Control for DVD FunctionsOperating the precoded function for your DVD player Precoded DVD ButtonsMY VCR/PVR Code is Remote Control for VCR/PVR FunctionsPrecoded VCR/PVR Buttons MY Audio Component Code is Remote Control for Additional Audio EquipmentOperating the precoded function for your Audio component Precoded Audio ButtonsInput Access How to Use the ENT ButtonVCR Brand Code Remote Control CodesSET TOP BOX BRAND..CODE On-Screen Display TV Guide On Screen Video Mode OFFBlack Side Panel Reset Video SettingsVertical Position BBE AudioSRS Second Audio Program SA Stereo STMono DRC LanguageDigital Output TV Guide On Screen To Setup the TV Guide On Screen SystemSetup Procedure TV Guide On Screen TV Guide On Screen TV Guide On Screen TV Guide On Screen Using the TV Guide On Screen System Schedule Navigating the TV Guide on Screen SystemName Description TV Guide On Screen IconsTune to Channel / Watch NOW GO to Service BARCancel ListingsExample Category Search Movies SearchDelete Search Example Keyword SearchTo Edit or Delete a keyword Edit SearchEdit Recording ScheduleWatch NOW/TUNE to Channel Delete RecordingRecording Notification Banner How to RemindRecording Conflict Tile How to set a reminderSelect these options SetupReminder Notification Banner Remind Conflict Remind conflict message will appear ifChange Channel Display Change System SettingsRemind Defaults Change Default OptionsGeneral Default Options Record DefaultsIR Defaults Channel Manager Signal MeterSignal Meter Channel List Start or Reset optionFavorites settings Auto Channel ScanLocks Change Access CodeMotion Picture Ratings Table Locks Rear Panel JacksMovie Ratings TV Parental Guide Ratings Table TV RatingsCanadian Ratings English Table Canadian Ratings EngCanadian Ratings French Chart Cursor PAD TimersSet The Clock Press Cursor PADOFF. Using Cursor PAD Set Sleep TimerSet Day/Night Timer ON. Using Cursor PADSolid SetupSET the Menu Background Shaded or Set The Inputs Lamp Power ControlSet AV Net Input 4 Auto LinkAV NET Setup Wizard Example A/V Receiver Setup AV NET Setup Wizard Example DVD Setup Learning Mode NET SetupUse the Cursor PAD Select the Soft Key to learn Ex. VOL Learning Mode Example CUSTOM/DVD 3 Setup To move on to the next Setup screen Setup Analog Captions Caption ModeSet Closed Caption Caption DisplayFixed Set Monitor OutMonitor TV Tuner OutANT Quick Start Up UpgradesUpgrade NOW Insert MMC CardLamp Life Lamp ReplacementLamp Replacement 120V Useful Information Phillips Head Screw Driver Lamp Compartment Do not Equipment Care and TroubleshootingTroubleshooting Switch ON/OFFTV Guide On ScreenTM System Frequently Asked Questions How can I look for a specific show in the Guide? What do the frequencies for Record and Remind mean?Reception Problems Inputs Features and SpecificationsFeatures DimensionsMeadowpine Blvd Mississauga, Ontario L5N 6C3 Home Electronics DivisionDigital Media Division Canada 1-800-HITACHIEND User License Agreement for Hitachi DTV Software End User Licence Agreement for Hitachi DTV SoftwareImage Input Type Format Aspect Video ID Auto Aspect AppendixesInformation and press the Select button Appendix ELocks Index102 103 QR64431