Crown CTS 2000, CTS 3000, CTS 1200, CTS 600 manual Dimensions, Weight

Page 17

`` SPECIFICATIONS

Performance

Frequency Response (at line out): 20 Hz to 20 kHz +/- 1 dB.

Signal to Noise Ratio (master volume at minimum): 100 dB.

THD: 0.05% typical with 800 mV balanced input, 1V output.

Input Sensitivity (volts RMS for full output at maximum gain):

Balanced mic inputs: 3 mV.

Balanced line inputs: 800 mV.

RCA connectors: 400 mV.

Input Impedance (nominal):

Mic: 400 ohms.

Line: 100 kilohms.

RCA: 50 kilohms.

Crosstalk (all controls at “10”): –50 dB at

1kHz.

Line Output Level (nominal): 1.2 V into 10 kilohms.

Phantom Power: 15 VDC.

AC Line Voltages Available:

100V 50/60 Hz

120V 60 Hz

220V 50/60 Hz

230V 50/60 Hz

240V 50/60 Hz

Operating Temperature/Humidity: 0° C to 40°

Cat 95% relative humidity (non-condensing).Storage Temperature: –20° C to 85° C.

Front Panel Controls and Indicators

Power Switch: Pushbutton on-off switch. The power switch does not affect the 24V DC auxiliary power input.

Input Volume Controls: Microphone/line, four in 14M, eight in 28M. Detented potentiometers with knobs.

Tone Controls: Bass and Treble non-detented potentiometers on each input channel. Bass ±10 dB at 100 Hz, Treble ±10 dB at 10 kHz.

Power Indicator: Blue LED indicates power on.

Input Signal Presence Indicator: Green LED, one for each input channel, illuminates when input signal exceeds –24 dBu (line) or –70 dBu (mic).

Output Signal Presence Indicator: Green LED, one for each output channel, illuminates when output signal level exceeds 100 mV.

Clip Indicators: Red LED, one per output channel. Illuminates at threshold of audible distortion.

Output Volume Controls: One per output chan- nel. Detented potentiometer with knob.

Back Panel Controls and Connectors

Fuse: Protects the power supply.

AC Power Inlet: Detachable IEC.

Auxiliary Power Input: 2-position terminal strip for 24 VDC (±10%) backup power. Accepts up to 10 AWG terminal forks.

Mixer Config Switch: A DIP switch with two functions:

1.Assigns an input as the priority input for each output, thereby temporarily muting the remaining inputs. Muting is activated by contact closure.

2.Global enable switch for phantom power. Does not affect RCA inputs. Default position is off.

Priority Connector: 3-pin Phoenix-type connec- tor allows Input 1 or Input 5 (28M only) to mute other input signals by contact closure.

Input Routing Switch (28M only): DIP switches that assign each input signal to each output. Two switches per input.

Line Out Connector: One 3-pin balanced Phoe- nix-type connector per output channel. Level controlled by master volume control.

Input Connectors:

Mic/Line Connector: 3-pin Phoenix-type, bal- anced, one per input channel.

Dual RCA Input Connector: For stereo music signals, unbalanced, summed together, two connectors per input channel.

The tone generator has been omitted. Call Crown Tech Support if you have a tone genera- tor question.

Mic/line Switch: Selects mic-level or line-level signals. One switch for each balanced input

Included Accessories

Power cord

Detachable rack ears

Phoenix-type connectors

Spade lugs

Dimensions

EIA Standard 19-inch (48.3-cm) rack mount width (EIA RS-310-B) with rack ears, 1.7-inch (4.3-cm) height and 10.7-inch (27.18-cm) depth

behind the mounting surface.

Weight

Net Weight:

14M: 8.7 lb (3.9 kg)

28M: 8.7 lb (3.9 kg)

Shipping Weight:

14M: 14 lb (6.4 kg)

28M: 14 lb (6.4 kg)

Regulatory Certifications

12/07

138119-1D

The Crown® 14M and 28M are high-value mixers for commercial and industrial audio. The mixers are part of Crown’s Commercial Audio Series, which also includes mixer-amplifiers and power amplifiers. These low-cost units provide all necessary features in a simple building-block format. Some applications include schools, hospitals, factories, restaurant/retail, houses of worship, fitness facilities, A/V boardrooms, correctional facilities, and small offices. Typical uses are paging, background music, security and evacuation instructions. Input routing allows each input to be assigned to any output. You can add more mixers for more inputs, or add more power amps (or mixer-amps) to handle more zones.

Other features include priority muting and phantom power.

COMMERCIAL AUDIO

Page 16 Page 18
Image 17
Page 16 Page 18
Contents Crown Power Amplifiers Page Installed Sound 250W 200W 1,200W 1,200W‡000W Back Panel Controls and Connectors Front Panel Controls and IndicatorsOptions Protection Systems220W † Operation per channel-pair 100V direct outputs220W 250W † 440WVoltage Gain at maximum level setting, 1.4V sensitivity CobraNet audio Analog audio inputs allow CobraNet network audio input260W 180W 270W 220WOverall Audio Performance SwitchesGeneral 500W Configuration with HiQnetImpedances and outputs 200W 650WRear Panel Controls and Connectors Included AccessoriesPerformance ProtectionOne-touch Performance AC Line Current Signal to Noise Ratio below rated 8-ohm power at 1 kHzRegulatory Certifications Page Commercial Audio Adaptable Weight DimensionsOr 2 inputs 1 to 2 amplifier output channels Power ZoneCooling Optional AccessoriesShipping Weight 60W ChannelAC Voltage Tolerance +10%/-20% Crosstalk all controls at 10 -70 dB at 1kHz Load ImpedanceAny input can be sent to any output Priority muting PracticalStorage Temperature -20 C to 85 C THD Less than 0.5% at rated power at 1 kHzAmp Config Switch a DIP switch with two functions Input Sensitivity for full output at maximum gain135MA, 160MA Back Panel Controls, Connectors and Indicators 40W Music & PagingActive Indicator Illuminates when VOX ducking is active THD 0.5% at rated power at 1 kHzVcap remote volume control 22 lb 9.98 kgSingle-zone XM EnabledTEL Input Connector Transformer-isolated Output Volume Control Detented potentiometer with knobActive Indicator LED illuminates when VOX ducking is active Page Portable PA 200W 000W World-Class600W 100WVoltage Gain at 1kHz, 8 ohm rated output HiQnet USB Connector Type B, connects to a HiQnet networkOptional Accessory 050W InnovationControls IndicatorsPureBandTM Crossover System Input/Output000W ‡ Evolution500W ‡ Shipping Weight 74.0 lb 33.6 kg Page Touring 250W 000W High power density, up to 9000 watts in a 2U chassis500W 600W 000W 100W 500W 000WBack Panel Connectors, Controls, and Indicators Summary SpecificationsFront Panel Indicators, Controls and Connectors Macro-Tech i Series The Legend Continues Firmware/Software Back Panel Controls, Indicators and ConnectorsPage Recording & Broadcast 110W 80W Tried & True50W Frequency Response ±0.1 dB from 20 Hz to 20 kHz at 1watt Output SignalPage Cinema 450W N E M a Performance Monitor IEC AC Power Receptacle Connects to an CTs 2-Channel 260W 180W 220W CTs Multi-ChannelPage Networked Products & Accessories SmartAmp Automation for TCP/IQ SmartAmp Automation for Networked AudioOperation and helps to save both time and money Ethernet networkPIP USP4 Remote Level Control Wall-Mount ControllersChoosing the Right Module 170V Constant-Voltage TransformerCommercial Audio Accessories Accessories3PLUS3 3+3 Extended Warranty Cover your ampPage Product Applications & Warranty Page Page Accessories & Applications LIVE Sound Product Applications Crown Amplifier Warranty WORLDWIDE­EXCEPT USA & CANADA Summary of Warranty

CTS 600, CTS 1200, CTS 2000, CTS 3000 specifications

Crown, a leading name in material handling equipment, has developed the Crown CTS series, which includes the CTS 3000, CTS 2000, CTS 600, and CTS 1200 models. Each of these rugged machines is designed to enhance productivity and efficiency in various warehouse and distribution applications, integrating innovative technologies and robust features.

The Crown CTS 3000 is the flagship model in this series, designed for high-demand environments that require exceptional lifting capability. It boasts a powerful AC drive system that offers superior acceleration and speed control, providing operators with smooth and responsive handling. The heightened visibility from the operator's compartment minimizes blind spots, enhancing safety and efficiency during operations. The CTS 3000 also features advanced battery management technology, allowing for prolonged operation and minimal downtime.

Next in line is the Crown CTS 2000, which is tailored for a range of medium-duty applications. While its lifting capacity is slightly lower than the CTS 3000, it incorporates many similar functionalities. It features a user-friendly control interface, making it easy for operators of any skill level to manage tasks efficiently. The robust design ensures reliability and durability, making it an excellent choice for businesses that require consistent performance under moderately demanding conditions.

The Crown CTS 600 model is specially designed for light-duty operations. Ideal for shorter runs and smaller spaces, the CTS 600 is compact and maneuverable without compromising on performance. It comes equipped with advanced safety features, including an integrated operator presence system that ensures safe operation. The model’s light weight also translates into better battery efficiency, making it a cost-effective option for businesses seeking to optimize their operational expenses.

Lastly, the Crown CTS 1200 is a versatile model that strikes a balance between power and agility. It is particularly suitable for environments where space is at a premium. The CTS 1200 is engineered for versatility, allowing it to handle a variety of loads with ease. It features intuitive controls and exceptional ergonomics, contributing to operator comfort during long shifts. This model also emphasizes energy efficiency and reduced environmental impact through its advanced power management system.

In summary, the Crown CTS series offers a range of models catering to varying operational needs, from high-demand environments with the CTS 3000 to the space-saving capabilities of the CTS 600. Each model is built upon a foundation of advanced technologies that promote safety, efficiency, and productivity, making them indispensable tools in today's material handling landscape.
Top Page Image Contents