Crown CTS 600, CTS 3000 manual Back Panel Controls, Indicators and Connectors, Firmware/Software

Page 43

`` SPECIFICATIONS

Performance

Frequency Response

(at 1 watt, 20 Hz - 20 kHz into 8 ohms): ±0.25 dB.

Signal to Noise Ratio

(below rated full-bandwidth power, A-weighted): >112 dB.

Total Harmonic Distortion (THD)

(at 2 watts into 8 ohms): < 0.1%.

Total Harmonic Distortion (THD) Plus Noise (at full rated power): < 0.35%, 20 Hz to 20 kHz.

Intermodulation Distortion (IMD)

(60 Hz and 7 kHz at 4:1,

from full rated output to –30 dB): < 0.35%.

Damping Factor (20 Hz to 100 Hz at 8 ohms): > 5000.

Crosstalk (below rated power, 20 Hz to 1 kHz): > 80 dB.

Common Mode Rejection (CMR)

(20 Hz to 1 kHz): 55 dB, typically >70 dB.

DC Output Offset (shorted input): < ± 3 mV.

Input Impedance (nominal):

10 kilohms balanced, 5 kilohms unbalanced.

Maximum Input Level: +20 dBu typical.

Network: Onboard HiQnet™, compatible with standard 100 Mb Ethercom hardware.

Load Impedance: (Note: Safe with all types of loads)

Stereo: 1/2/4/8/16 ohms.

Bridge Mono: 2/4/8 ohms.

Input Sensitivity (referenced to 8 ohm rated output): 1.4V, 32 dB gain, and 26 dB gain.

Voltage Gain (referenced to 8 ohm rated output):

MA-5000i: 37.1 dB to 22.2 dB

MA-9000i: 37.9 dB to 23.0 dB

MA-12000i: 39.3 dB to 24.5 dB

Required AC Mains: Universal AC input, 100- 240VAC, 50/60 Hz (±10%). Maximum AC mains voltage 264VAC.

AC Line Connector: Five cordsets supplied with amplifier (USA, UK, European, Australia, India).

Front Panel Controls and Indicators

Bridge Mode Indicator: Amber LED illuminates when the amplifier is set to Bridge-Mono mode.

Ready Indicator: Green LED, one per channel.

On (bright): Ready.

On (dim): Onset of compression.

Off: Thermal failure.

Signal Indicators: One green LED per channel.

Solid green: Input signal is above –40 dBu.

Bright green: Channel’s output signal has reached the onset of audible clipping.

Power Indicator: Blue LED indicates amplifier has been turned on and AC power is available. The LED will flash when the AC line voltage is 10% above or below the nominal rated value.

Data Indicator: Yellow LED on front panel indicates network data activity. Data indicator flashes only when the amplifier is polled for data, or is polled to see whether it is online

Power Switch: Push-on/push-off switch with built-in green AC mains present indicator.

Volume Control: Precision detented attenuator with 31 steps, press-and-hold mute function.

Volume Control LED Ring: A ring of green LEDs around each volume control show the position of the control. Entire ring flashes when channel is muted. Can be converted to be a level meter.

Back Panel Controls, Indicators and Connectors

Power Cord Connector: Detachable 20 amp IEC inlet. Cord locks with suppliled cord retention clip. Voltage range is indicated above IEC inlet.

Reset Switch/Circuit Breaker: If the current draw of the amplifier exceeds safe limits, this breaker automatically disconnects the power supply from the AC mains. The switch resets the circuit breaker.

Output Connectors: Two high-current, 50A Neutrik® Speakon® NL4MLP (mates with NL4FC or NL4), one per channel. Ch 1 Speakon® is wired with Ch 1 and Ch 2 outputs for use with single 4-conductor cable. Two pairs of high-current, 60A color-coded5-way binding posts (for banana plugs, spade lugs or bare wire).

Analog Input Connectors: A 3-pin female XLR connector for each channel.

Analog Loop Thru Connectors: Two male XLR passive analog loop through.

Mode Switch/Indicator: Sets amplifier to Stereo, Bridge, or Input Y mode. OFF=Stereo, YEL=Bridge, GRN=Y.

Network Connectors: Two Neutrik® Ethercon connector accepts RJ-45 type connectors for HiQnet™ networking. Next to each connector is a yellow LINK ACT indicator that shows network activity, and a green 100Mb indicator that shows a 100Mb network connection.

Data Indicator: Yellow LED on back panel indicates network data activity. Data indicator flashes only when the amplifier is polled for data, or is polled to see whether it is online.

Preset Indicator: Green/yellow LED flashes to signal the number of the current preset. LED is green if current preset is active, or is yellow if current preset is modified.

Input Sensitivity Switch: Three-position switch providing 1.4V, 32 dB, and 26 dB settings for both channels.

Firmware/Software

Firmware can be updated at www.crownaudio. com > Support > Downloads.

Software features: Same as PIP-Lite module

(except no Listen Bus): User Presets, Clip Event Monitor, Input Signal Level Monitor, Output Signal Level Monitor, Thermal Headroom Level Monitor, Power/Standby Control, Signal Mute, Polarity Inverter, Input Signal Fader, Dynamic Gain Monitors (Ghost Faders), Amplifier Information, User and Channel Labels, Amplifier Mode, Amplifier Output Mode, Line Voltage Monitor, Error Reporting, Auto Standby, Input Signal Compressor/Limiter, Peak Voltage Limiter, Average Power Limiter, Clip Eliminator, Thermal Limiter, Limiter Tie, Load Supervision.

Construction

Cooling: Dual-zone, microprocessor controlled, continuously variable speed fans, front-to-back airflow.

Front Panel: Cast aluminum with integrated handles.

Dimensions: 19 in. (48.3 cm) W x 3.5 in. (8.9 cm) H x 16.2 in. (41.1 cm) D.

Weight: 28 lbs (12.7 kg) net, 36 lbs (16.3 kg) shipping.

Protection: Amplifier is protected against reactive loads, faults and shorts. If one channel experiences a catastrophic failure, the entire amplifier will shut down.

Included Accessories: Rear rack ears, rack screws, operation manual, power cords, foam air filter.

Regulatory Certifications

Other Applications

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

4/08

 

140535-2

The Crown Macro-Tech i Series amplifiers continue the Macro-Tech legacy of unparalleled sonic accu- racy and detail, putting sound quality above all else. Their patented, cutting-edge Class-I circuitry gets more power out of an amplifier with less waste. Each model features a Global Power Supply designed to deliver maximum power in any country. The i Series offers studio-quality analog signal processing with built-in load, line voltage, input and output monitoring. Standard Ethernet networking via System Architect provides integrated monitoring and control to give system operators access to the system from

any location.

T O U R I N G

Page 42 Page 44
Image 43
Page 42 Page 44
Contents Crown Power Amplifiers Page Installed Sound 000W 200W 1,200W 1,200W‡250W Protection Systems Front Panel Controls and IndicatorsBack Panel Controls and Connectors Options440W Operation per channel-pair 100V direct outputs220W † 220W 250W †Voltage Gain at maximum level setting, 1.4V sensitivity 270W 220W Analog audio inputs allow CobraNet network audio inputCobraNet audio 260W 180WGeneral SwitchesOverall Audio Performance 200W 650W Configuration with HiQnet500W Impedances and outputsProtection Included AccessoriesRear Panel Controls and Connectors PerformanceOne-touch Performance Regulatory Certifications Signal to Noise Ratio below rated 8-ohm power at 1 kHzAC Line Current Page Commercial Audio Adaptable Weight DimensionsOr 2 inputs 1 to 2 amplifier output channels Power ZoneShipping Weight Optional AccessoriesCooling 60W ChannelAC Voltage Tolerance +10%/-20% Crosstalk all controls at 10 -70 dB at 1kHz Load ImpedanceAny input can be sent to any output Priority muting PracticalInput Sensitivity for full output at maximum gain THD Less than 0.5% at rated power at 1 kHzStorage Temperature -20 C to 85 C Amp Config Switch a DIP switch with two functions135MA, 160MA Back Panel Controls, Connectors and Indicators 40W Music & Paging22 lb 9.98 kg THD 0.5% at rated power at 1 kHzActive Indicator Illuminates when VOX ducking is active Vcap remote volume controlSingle-zone XM EnabledActive Indicator LED illuminates when VOX ducking is active Output Volume Control Detented potentiometer with knobTEL Input Connector Transformer-isolated Page Portable PA 100W World-Class200W 000W 600WOptional Accessory HiQnet USB Connector Type B, connects to a HiQnet networkVoltage Gain at 1kHz, 8 ohm rated output 050W InnovationInput/Output IndicatorsControls PureBandTM Crossover System500W ‡ Evolution000W ‡ Shipping Weight 74.0 lb 33.6 kg Page Touring 100W 500W 000W High power density, up to 9000 watts in a 2U chassis250W 000W 500W 600W 000WFront Panel Indicators, Controls and Connectors Summary SpecificationsBack Panel Connectors, Controls, and Indicators Macro-Tech i Series The Legend Continues Firmware/Software Back Panel Controls, Indicators and ConnectorsPage Recording & Broadcast 50W Tried & True110W 80W Frequency Response ±0.1 dB from 20 Hz to 20 kHz at 1watt Output SignalPage Cinema 450W N E M a Performance Monitor IEC AC Power Receptacle Connects to an CTs 2-Channel 260W 180W 220W CTs Multi-ChannelPage Networked Products & Accessories Ethernet network SmartAmp Automation for Networked AudioSmartAmp Automation for TCP/IQ Operation and helps to save both time and moneyPIP USP4 170V Constant-Voltage Transformer Wall-Mount ControllersRemote Level Control Choosing the Right ModuleCover your amp AccessoriesCommercial Audio Accessories 3PLUS3 3+3 Extended WarrantyPage Product Applications & Warranty Page Page Accessories & Applications LIVE Sound Product Applications Crown Amplifier Warranty WORLDWIDE­EXCEPT USA & CANADA Summary of Warranty

CTS 600, CTS 1200, CTS 2000, CTS 3000 specifications

Crown, a leading name in material handling equipment, has developed the Crown CTS series, which includes the CTS 3000, CTS 2000, CTS 600, and CTS 1200 models. Each of these rugged machines is designed to enhance productivity and efficiency in various warehouse and distribution applications, integrating innovative technologies and robust features.

The Crown CTS 3000 is the flagship model in this series, designed for high-demand environments that require exceptional lifting capability. It boasts a powerful AC drive system that offers superior acceleration and speed control, providing operators with smooth and responsive handling. The heightened visibility from the operator's compartment minimizes blind spots, enhancing safety and efficiency during operations. The CTS 3000 also features advanced battery management technology, allowing for prolonged operation and minimal downtime.

Next in line is the Crown CTS 2000, which is tailored for a range of medium-duty applications. While its lifting capacity is slightly lower than the CTS 3000, it incorporates many similar functionalities. It features a user-friendly control interface, making it easy for operators of any skill level to manage tasks efficiently. The robust design ensures reliability and durability, making it an excellent choice for businesses that require consistent performance under moderately demanding conditions.

The Crown CTS 600 model is specially designed for light-duty operations. Ideal for shorter runs and smaller spaces, the CTS 600 is compact and maneuverable without compromising on performance. It comes equipped with advanced safety features, including an integrated operator presence system that ensures safe operation. The model’s light weight also translates into better battery efficiency, making it a cost-effective option for businesses seeking to optimize their operational expenses.

Lastly, the Crown CTS 1200 is a versatile model that strikes a balance between power and agility. It is particularly suitable for environments where space is at a premium. The CTS 1200 is engineered for versatility, allowing it to handle a variety of loads with ease. It features intuitive controls and exceptional ergonomics, contributing to operator comfort during long shifts. This model also emphasizes energy efficiency and reduced environmental impact through its advanced power management system.

In summary, the Crown CTS series offers a range of models catering to varying operational needs, from high-demand environments with the CTS 3000 to the space-saving capabilities of the CTS 600. Each model is built upon a foundation of advanced technologies that promote safety, efficiency, and productivity, making them indispensable tools in today's material handling landscape.
Top Page Image Contents