Crown CTS 600, CTS 3000, CTS 2000 Controls, PureBandTM Crossover System, Indicators, Input/Output

Page 35

`` SPECIFICATIONS

Performance

Sensitivity (for full rated power at 4 ohms): 1.4 Vrms.

Frequency Response

(at 1 watt, 20 Hz to 20 kHz): +0 dB, –1 dB.

Signal-to-Noise Ratio

Rated as dBr to full rated 8 ohms power output (A-weighted):

XLS1000: > 97 dB.

XLS1500, XLS2000, XLS2500: > 103 dB.

Total Harmonic Distortion (THD): < 0.5%.

Intermodulation Distortion (IMD):

(60 Hz and 7 kHz at 4:1) from full rated output to –30 dB: < 0.3%.

Damping Factor (8 ohm) 10 Hz to 400 Hz: > 600.

Crosstalk (below rated 8 ohm power): at 1 kHz: > 85 dB.

at 20 kHz: > 60 dB.

Input Impedance (nominal):

20 kilohms balanced, 10 kilohms unbalanced.

Load Impedance: 2 to 8 ohms per channel in Stereo, 4 to 8 ohms in Bridge Mono.

AC Line Voltage and Frequency Configurations Available (±10%): 120 VAC 60 Hz, 100 VAC 50/60 Hz, 220 and 240 VAC 50 Hz.

Controls

Level: Two front-panel rotary level controls, one for each channel.

LCD Screen: Back-lit LCD allows for crossover configuration, amp mode configuration and clip compressor configuration.

Menu/Prev/Select: Three buttons located near the LCD screen that are used to configure and access the integrated processing.

Power: Front-panel switch; on when in the IN position. Blue LED will illuminate when on.

Circuit Breaker: Back-panel breaker provides overload protection.

PureBandTM Crossover System

Crossover Filter:

Linkwitz-Riley 24dB per ocatve.

Crossover Mode:

Crossover (CH1=LPF, CH2=HPF), Low Pass (both channels LPF), High Pass (both channels HPF), Bridge (LPF or HPF).

PeakXTM Limiters: Channel independent clip limiter designed to provide maximum output while protecting your loudspeakers.

Indicators

Signal Presence Indicators: Two green LEDs, one for each channel, illuminate when the channel’s input signal exceeds –40 dBu.

–10 Indicator: Green LED flashes when output signal exceeds –10 dB below clip.

–20 Indicator: Green LED flashes when output signal level exceeds –20 dB below clip.

Clip Indicators: Two red LEDs, one for each channel, illuminate when the channel’s output is being overdriven.

Thermal Indicator: Two red LEDs, one for each channel, illuminate when thermal compression begins.

Input/Output

Input Connectors: XLR (one per channel), 1/4 inch (one per channel), and RCA (one per channel). The 1/4 inch inputs can be used as loop-thrus to distribute signal to multiple amplifiers.

Output Connectors: Two 4-Pole Speakon® Output Connectors accept 2-pole or 4-pole Speakon® connectors. The top Speakon connector is wired for both channels so it can be used for bridge-mono wiring or for stereo wiring of two speakers to a single Speakon connector.

One pair of back-panel binding posts per channel; accepts banana plugs or bare wire. (European models do not accept banana plugs.)

Protection

XLS Series amplifiers provide extensive protection and diagnostic capabilities, including output current limiting, DC protection, circuit breaker, and thermal protection.

Construction

Ventilation: Flow-through ventilation from front to back.

Cooling: Internal heat sinks with forced-air cooling for rapid, uniform heat dissipation.

Air Volume Requirements

(per minute per unit): 80.15 ft³ (2.27 m³).

Dimensions:EIA Standard 19-inch (48.3-cm) rack mount width (EIA RS-310-B), 3.5-inch (8.9-cm) height.

XLS1000/1500: 8.10-inch (20.6-cm) depth.

XLS2000/2500: 10.35-inch (26.3-cm) depth.

Weight

Net Weight:

XLS1000: 8.6 lb (3.9 kg)

XLS1500: 8.6 lb (3.9 kg)

XLS2000: 10.75 lb (4.9 kg)

XLS2500: 10.75 lb (4.9 kg)

Shipping Weight:

XLS1000: 13.6 lb (6.2 kg)

XLS1500: 13.6 lb (6.2 kg)

XLS2000: 15.75 lb (7.1 kg)

XLS2500: 15.75 lb (7.1 kg)

Regulatory Certifications

Other Applications

Take command of center stage with Crown's new XLS amplifiers. The high- performance class-D amplifier combined with its integrated PureBand™ Crossover System deliver unmatched performance and sound; while its multiple inputs let you plug in anything you want. PeakX™ Limiters effortlessly protect your speaker investment, and at 11 pounds moving from show to show is nearly effortless. Powerful, flexible, portable, and reliable – RUN THE SHOW with a power amplifier

designed to play hard all night long.

P O R TA B L E P A

Image 35
Contents Crown Power Amplifiers Page Installed Sound 250W 200W 1,200W 1,200W‡000W Protection Systems Front Panel Controls and IndicatorsBack Panel Controls and Connectors Options440W Operation per channel-pair 100V direct outputs220W † 220W 250W †Voltage Gain at maximum level setting, 1.4V sensitivity 270W 220W Analog audio inputs allow CobraNet network audio inputCobraNet audio 260W 180WOverall Audio Performance SwitchesGeneral 200W 650W Configuration with HiQnet500W Impedances and outputsProtection Included AccessoriesRear Panel Controls and Connectors PerformanceOne-touch Performance AC Line Current Signal to Noise Ratio below rated 8-ohm power at 1 kHzRegulatory Certifications Page Commercial Audio Adaptable Weight DimensionsOr 2 inputs 1 to 2 amplifier output channels Power ZoneCooling Optional AccessoriesShipping Weight 60W ChannelAC Voltage Tolerance +10%/-20% Crosstalk all controls at 10 -70 dB at 1kHz Load ImpedanceAny input can be sent to any output Priority muting PracticalInput Sensitivity for full output at maximum gain THD Less than 0.5% at rated power at 1 kHzStorage Temperature -20 C to 85 C Amp Config Switch a DIP switch with two functions135MA, 160MA Back Panel Controls, Connectors and Indicators 40W Music & Paging22 lb 9.98 kg THD 0.5% at rated power at 1 kHzActive Indicator Illuminates when VOX ducking is active Vcap remote volume controlSingle-zone XM EnabledTEL Input Connector Transformer-isolated Output Volume Control Detented potentiometer with knobActive Indicator LED illuminates when VOX ducking is active Page Portable PA 100W World-Class200W 000W 600WVoltage Gain at 1kHz, 8 ohm rated output HiQnet USB Connector Type B, connects to a HiQnet networkOptional Accessory 050W InnovationInput/Output IndicatorsControls PureBandTM Crossover System000W ‡ Evolution500W ‡ Shipping Weight 74.0 lb 33.6 kg Page Touring 100W 500W 000W High power density, up to 9000 watts in a 2U chassis250W 000W 500W 600W 000WBack Panel Connectors, Controls, and Indicators Summary SpecificationsFront Panel Indicators, Controls and Connectors Macro-Tech i Series The Legend Continues Firmware/Software Back Panel Controls, Indicators and ConnectorsPage Recording & Broadcast 110W 80W Tried & True50W Frequency Response ±0.1 dB from 20 Hz to 20 kHz at 1watt Output SignalPage Cinema 450W N E M a Performance Monitor IEC AC Power Receptacle Connects to an CTs 2-Channel 260W 180W 220W CTs Multi-ChannelPage Networked Products & Accessories Ethernet network SmartAmp Automation for Networked AudioSmartAmp Automation for TCP/IQ Operation and helps to save both time and moneyPIP USP4 170V Constant-Voltage Transformer Wall-Mount ControllersRemote Level Control Choosing the Right ModuleCover your amp AccessoriesCommercial Audio Accessories 3PLUS3 3+3 Extended WarrantyPage Product Applications & Warranty Page Page Accessories & Applications LIVE Sound Product Applications Crown Amplifier Warranty WORLDWIDE­EXCEPT USA & CANADA Summary of Warranty

CTS 600, CTS 1200, CTS 2000, CTS 3000 specifications

Crown, a leading name in material handling equipment, has developed the Crown CTS series, which includes the CTS 3000, CTS 2000, CTS 600, and CTS 1200 models. Each of these rugged machines is designed to enhance productivity and efficiency in various warehouse and distribution applications, integrating innovative technologies and robust features.

The Crown CTS 3000 is the flagship model in this series, designed for high-demand environments that require exceptional lifting capability. It boasts a powerful AC drive system that offers superior acceleration and speed control, providing operators with smooth and responsive handling. The heightened visibility from the operator's compartment minimizes blind spots, enhancing safety and efficiency during operations. The CTS 3000 also features advanced battery management technology, allowing for prolonged operation and minimal downtime.

Next in line is the Crown CTS 2000, which is tailored for a range of medium-duty applications. While its lifting capacity is slightly lower than the CTS 3000, it incorporates many similar functionalities. It features a user-friendly control interface, making it easy for operators of any skill level to manage tasks efficiently. The robust design ensures reliability and durability, making it an excellent choice for businesses that require consistent performance under moderately demanding conditions.

The Crown CTS 600 model is specially designed for light-duty operations. Ideal for shorter runs and smaller spaces, the CTS 600 is compact and maneuverable without compromising on performance. It comes equipped with advanced safety features, including an integrated operator presence system that ensures safe operation. The model’s light weight also translates into better battery efficiency, making it a cost-effective option for businesses seeking to optimize their operational expenses.

Lastly, the Crown CTS 1200 is a versatile model that strikes a balance between power and agility. It is particularly suitable for environments where space is at a premium. The CTS 1200 is engineered for versatility, allowing it to handle a variety of loads with ease. It features intuitive controls and exceptional ergonomics, contributing to operator comfort during long shifts. This model also emphasizes energy efficiency and reduced environmental impact through its advanced power management system.

In summary, the Crown CTS series offers a range of models catering to varying operational needs, from high-demand environments with the CTS 3000 to the space-saving capabilities of the CTS 600. Each model is built upon a foundation of advanced technologies that promote safety, efficiency, and productivity, making them indispensable tools in today's material handling landscape.