Crown CTS 600 manual THD Less than 0.5% at rated power at 1 kHz, Storage Temperature -20 C to 85 C

Page 23

`` SPECIFICATIONS

Performance

Frequency Reponse (at 1 watt from 4-ohm tap): 70 Hz to 19 kHz ± 1 dB.

Frequency Response (at line out): 20 Hz to 20 kHz ± 1 dB.

Power Bandwidth (at 4-ohm tap, 2 dB below maxium 1 kHz power): 50 Hz to 20 kHz with < 0.5% THD

Signal to Noise Ratio (ref. to rated power, master volume at minimum): 85 dB.

DC Output Offset: < ±5 mV.

THD: Less than 0.5% at rated power at 1 kHz.

Input Sensitivity (for full output at maximum gain):

Balanced mic inputs: 3 mV.

Balanced line inputs: 800 mV.

RCA connectors: 400 mV.

Input Impedance (nominal):

Mic: 400 ohms.

Line: 100 kilohms.

RCA: 50 kilohms.

Crosstalk: –70dB at 1kHz.

Line Output Level (nominal): 1V into 10 kilohms.

Phantom Power: 15 VDC.

AC Line Voltages Available:

100V 50/60 Hz

120V 60 Hz

220V 50/60 Hz

230V 50/60 Hz

240V 50/60 Hz

Operating Temperature/Humidy: 0° C to 40° C at 95% relative humidity (non-condensing).

Storage Temperature: –20° C to 85° C.

Front Panel Controls and Indicators

Power Switch: Pushbutton on-off switch. The power switch does not affect the 24V DC auxiliary power input.

Input Volume Controls: Microphone/line, four in 180MA and 1160MA, eight in 280MA. Detented potentiometers with knobs.

Tone Controls: Bass and Treble non-detented recessed potentiometers on each input chan- nel. Bass ±10 dB at 100 Hz, Treble ±10 dB at 10 kHz.

Power Indicator: Blue LED indicates power on.

Input Signal Presence Indicator: Green LED, one for each input channel, illuminates when input signal exceeds –24 dBu (line) or –70 dBu (mic).

Output Signal Presence Indicator: Green LED, one for each output channel, illuminates when output signal level exceeds 100 mV (45 dB below full power) from the 4-ohm tap. Does not respond to signals from the AMP INPUT connector.

Clip Indicators: Red LED, one per output chan- nel. Illuminates at threshold of audible distor- tion. Does not respond to signals from the AMP INPUT connector.

Output Volume Controls: One per output chan- nel. Detented potentiometer with knob.

Back Panel Controls and Connectors

Reset Switch: Resets the circuit breaker that protects the power supply. 220/230/240V units have a fuse instead.

AC Power Inlet: Detachable IEC.

Auxiliary Power Input: 2-position terminal strip for 24 VDC (±10%) backup power. Accepts up to 14 AWG terminal forks.

Amplifier Outputs Connectors: One per channel, 4-position terminal strip with COM (Common), 4 ohms, 70V and 100V terminals. Accepts up to 14 AWG terminal forks. Non- touch cover included.

Output VCA Connector: 4-pinPhoenix-type connector for two VCA control lines of +10 VDC and ground. Compatible with Crown 1-VCAP and 4-VCAP modules.

Amp Config Switch: A DIP switch with two functions:

1.Assigns an input as the priority input for each output, thereby temporarily muting the remaining inputs. Muting is activated by contact closure.

2.Global enable switch for phantom power. Does not affect RCA inputs. Default position is off.

Priority Connector: 3-pin Phoenix-type connec- tor allows Input 1 or Input 5 (280MA only) to mute other input signals by contact closure.

Input Routing Switch (280MA only): DIP switches that assign each input signal to each output. Two switches per input.

Line Out Connector: One 3-pin balanced Phoe- nix-type connector per output channel. Post master, pre-VCA. Level controlled by master volume control.

The tone generator has been omitted. Call Crown Tech Support if you have a tone genera- tor question.

Input Connectors:

Mic/Line Connector: 3-pin Phoenix-type, bal- anced, one per input channel.

Dual RCA Input Connector: For stereo music signals, unbalanced, summed together, two connectors per input channel.

Amp Input Connector: 3-pin Phoenix-type, high-impedance balanced, one per amplifer channel. Used to link an additional mixer to the mixer-amplifier. Can be used to connect an external processor.

Mic/line Switch: Selects mic-level or line-level signals. One switch for each balanced input.

Link In/Out Switch: Slide switch, one per chan- nel. With the Link Switch IN, any signal applied to the Amp Input connector will be mixed with the input signal(s). With the Link Switch OUT, only the signal from the Amp Input Connector will appear at the amplifier output.

Cooling

Convection cooled.

Protection

Current Limit Protection: Included.

Thermal Limit Protection: Over-temperature thermal cutout.

DC-Fault Load Protection: Included.

Included Accessories

Power cord Detachable rack ears Screws for rack ears

Non-touch cover for output connectors Phoenix-type connectors

Spade lugs

Optional Accessories

1-VCAP remote volume control for one channel. 4-VCAP remote volume control for four chan- nels.

Dimensions

EIA Standard 19-inch (48.3-cm) rack mount width (EIA RS-310-B) with rack ears, 3.5-inch (8.9-cm) height and 12.2-inch (31.0-cm) depth behind the mounting surface (not including non- touch cover). 4.1 inches (10.5 cm) high includ- ing feet. 13.9 inches (35.2 cm) deep from front of knobs to back of non-touch cover.

Weight

Net Weight:

180MA: 21.0 lbs. (9.5 kg).

280MA: 25.3 lbs. (11.5 kg)

1160MA: 25.3 lbs. (11.5 kg)

Shipping Weight:

180MA: 26.0 lbs. (11.8 kg)

280MA: 30.3 lbs. (13.8 kg)

1160MA: 30.3 lbs. (13.8 kg)

Regulatory Certifications

 

 

 

 

 

 

 

 

 

 

 

 

 

 

12/07

 

 

 

 

137964-2B

COMMERCIAL AUDIO

Crown’s Commercial Audio mixer/amplifiers deliver legendary Crown quality to the commercial audio industry. These high-value mixer-amplifiers provide both 4-ohm and constant-voltage outputs (70V and 100V) for use in a wide range of commercial applications including schools, hospitals, factories, restaurant/retail, houses of worship, fitness facilities, A/V boardrooms, correctional facilities, and small offices. Easily configured for a range of uses such as paging, background music, security, and evacua-

tion instructions, Crown’s Commercial Audio units are the smart choice for commercial sound.

Page 22 Page 24
Image 23
Page 22 Page 24
Contents Crown Power Amplifiers Page Installed Sound 250W 200W 1,200W 1,200W‡000W Protection Systems Front Panel Controls and IndicatorsBack Panel Controls and Connectors Options440W Operation per channel-pair 100V direct outputs220W † 220W 250W †Voltage Gain at maximum level setting, 1.4V sensitivity 270W 220W Analog audio inputs allow CobraNet network audio inputCobraNet audio 260W 180WOverall Audio Performance SwitchesGeneral 200W 650W Configuration with HiQnet500W Impedances and outputsProtection Included AccessoriesRear Panel Controls and Connectors PerformanceOne-touch Performance AC Line Current Signal to Noise Ratio below rated 8-ohm power at 1 kHzRegulatory Certifications Page Commercial Audio Adaptable Weight DimensionsOr 2 inputs 1 to 2 amplifier output channels Power ZoneCooling Optional AccessoriesShipping Weight 60W ChannelAC Voltage Tolerance +10%/-20% Crosstalk all controls at 10 -70 dB at 1kHz Load ImpedanceAny input can be sent to any output Priority muting PracticalInput Sensitivity for full output at maximum gain THD Less than 0.5% at rated power at 1 kHzStorage Temperature -20 C to 85 C Amp Config Switch a DIP switch with two functions135MA, 160MA Back Panel Controls, Connectors and Indicators 40W Music & Paging22 lb 9.98 kg THD 0.5% at rated power at 1 kHzActive Indicator Illuminates when VOX ducking is active Vcap remote volume controlSingle-zone XM EnabledTEL Input Connector Transformer-isolated Output Volume Control Detented potentiometer with knobActive Indicator LED illuminates when VOX ducking is active Page Portable PA 100W World-Class200W 000W 600WVoltage Gain at 1kHz, 8 ohm rated output HiQnet USB Connector Type B, connects to a HiQnet networkOptional Accessory 050W InnovationInput/Output IndicatorsControls PureBandTM Crossover System000W ‡ Evolution500W ‡ Shipping Weight 74.0 lb 33.6 kg Page Touring 100W 500W 000W High power density, up to 9000 watts in a 2U chassis250W 000W 500W 600W 000WBack Panel Connectors, Controls, and Indicators Summary SpecificationsFront Panel Indicators, Controls and Connectors Macro-Tech i Series The Legend Continues Firmware/Software Back Panel Controls, Indicators and ConnectorsPage Recording & Broadcast 110W 80W Tried & True50W Frequency Response ±0.1 dB from 20 Hz to 20 kHz at 1watt Output SignalPage Cinema 450W N E M a Performance Monitor IEC AC Power Receptacle Connects to an CTs 2-Channel 260W 180W 220W CTs Multi-ChannelPage Networked Products & Accessories Ethernet network SmartAmp Automation for Networked AudioSmartAmp Automation for TCP/IQ Operation and helps to save both time and moneyPIP USP4 170V Constant-Voltage Transformer Wall-Mount ControllersRemote Level Control Choosing the Right ModuleCover your amp AccessoriesCommercial Audio Accessories 3PLUS3 3+3 Extended WarrantyPage Product Applications & Warranty Page Page Accessories & Applications LIVE Sound Product Applications Crown Amplifier Warranty WORLDWIDE­EXCEPT USA & CANADA Summary of Warranty

CTS 600, CTS 1200, CTS 2000, CTS 3000 specifications

Crown, a leading name in material handling equipment, has developed the Crown CTS series, which includes the CTS 3000, CTS 2000, CTS 600, and CTS 1200 models. Each of these rugged machines is designed to enhance productivity and efficiency in various warehouse and distribution applications, integrating innovative technologies and robust features.

The Crown CTS 3000 is the flagship model in this series, designed for high-demand environments that require exceptional lifting capability. It boasts a powerful AC drive system that offers superior acceleration and speed control, providing operators with smooth and responsive handling. The heightened visibility from the operator's compartment minimizes blind spots, enhancing safety and efficiency during operations. The CTS 3000 also features advanced battery management technology, allowing for prolonged operation and minimal downtime.

Next in line is the Crown CTS 2000, which is tailored for a range of medium-duty applications. While its lifting capacity is slightly lower than the CTS 3000, it incorporates many similar functionalities. It features a user-friendly control interface, making it easy for operators of any skill level to manage tasks efficiently. The robust design ensures reliability and durability, making it an excellent choice for businesses that require consistent performance under moderately demanding conditions.

The Crown CTS 600 model is specially designed for light-duty operations. Ideal for shorter runs and smaller spaces, the CTS 600 is compact and maneuverable without compromising on performance. It comes equipped with advanced safety features, including an integrated operator presence system that ensures safe operation. The model’s light weight also translates into better battery efficiency, making it a cost-effective option for businesses seeking to optimize their operational expenses.

Lastly, the Crown CTS 1200 is a versatile model that strikes a balance between power and agility. It is particularly suitable for environments where space is at a premium. The CTS 1200 is engineered for versatility, allowing it to handle a variety of loads with ease. It features intuitive controls and exceptional ergonomics, contributing to operator comfort during long shifts. This model also emphasizes energy efficiency and reduced environmental impact through its advanced power management system.

In summary, the Crown CTS series offers a range of models catering to varying operational needs, from high-demand environments with the CTS 3000 to the space-saving capabilities of the CTS 600. Each model is built upon a foundation of advanced technologies that promote safety, efficiency, and productivity, making them indispensable tools in today's material handling landscape.
Top Page Image Contents