Crown CTS 2000, CTS 3000, CTS 1200 Voltage Gain at 1kHz, 8 ohm rated output, Optional Accessory

Page 33

`` SPECIFICATIONS

Voltage Gain at 1kHz, 8 ohm rated output:

XTi 1000: 30.5 dB

XTi 2000: 32.9 dB

XTi 4000: 34.2 dB

XTi 6000: 37.1 dB

Frequency Response: +0/–1 dB from 20 Hz to 20 kHz at 1 watt into 4 ohms.

Load Impedance: Safe with all types of loads. Rated for 2 to 8 ohms in Stereo mode, 4 to

16 ohms in Bridge-Mono mode. The XTi 1000 A1 (100V version) is rated for 4 to 8 ohms Stereo, 8 to 16 ohms Bridge Mono.

Sensitivity: 1.4V

Signal to Noise Ratio (below rated 1 kHz power at 8 ohms): XTi 1K, 2K, 4K: 100 dB (A weighted). XTi 6K: 103 dB (A weighted).

Damping Factor: Better than 500 from 20 Hz to 400 Hz.

Crosstalk: > 70 dB below rated power, 20 Hz to 1 kHz.

Input Stage: Input is electronically balanced and employs precision 1% resistors.

Input Impedance (nominal): 20 k ohms, bal- anced;10 k ohms, unbalanced.

Maximum Input Signal: +22 dBu typical.

AC Line Voltage and Frequency Configura- tions Available: 100V, 120V, 220-240V 50/60 Hz.

AC Line Current (120VAC amplifier playing 1/8 power pink noise into 4 ohms per ch): XTi 1000: 6.8A, XTi 2000: 8.3A, XTi 4000:

10.5A; at idle draws no more than 38 watts.

XTi 6000: 15.3A; at idle draws no more than 180 watts.

Operating Temperature: 0° C to 40° C at 95% relative humidity (non-condensing).

DSP Section

Input EQ: 6 parametric filters per channel with adjustable Q, ±15 dB boost/cut. Also adjust- able high and low shelving filters. This 8-filter EQ section can be bypassed.

Crossover Filters: Highpass and lowpass per channel. Butterworth 6/12/18/24 dB per octave. Linkwitz-Riley 24/48 dB per octave. Also includes ±15 dB bandpass gain and polarity control.

Delay: For signal alignment of driver; 50 mS total delay.

Subharmonic Synthesizer: Takes the low- frequency content of the input signal and “synthesizes” a new signal that is the same as the input signal but one octave lower. The new synthesized signal is then mixed with the original signal to create the effect.

Output Limiter: Prevents clipping.

Presets: 20 presets, 19 of which are user- definable.

Front Panel Controls and Indicators

Level: Detented rotary level control, one per channel.

Power Switch: On/off switch applies AC power to the amplifier.

Sel/Prev/Next Buttons: Three buttons near the LCD screen are used to access menu items and front panel lockout.

LCD Screen: Backlit liquid crystal display shows speaker presets.

Signal Indicator: Green LED, one per chan- nel, illuminates when a very low-level signal is present at input. May be used for trouble- shooting cable runs.

–10 Indicator: Green LED flashes when output signal exceeds –10 dB below clip.

–20 Indicator: Green LED flashes when output signal level exceeds –20 dB below clip.

Ready Indicator: Green LED, one per chan- nel, illuminates when the amplifier is ready to produce audio.

Clip Indicator: Red LED, one per channel, turns on at the threshold of audible distortion.

Temp Indicator: Red LED, one per channel, illuminates under excessive temperature conditions.

Power Indicator: Blue LED illuminates when the amplifier has been turned on and has power.

Rear Panel Controls and Connectors

AC Line Connector:

XTi 1K, 2K, 4K: NEMA 5-15P (15A).

XTi 6K: NEMA 6-20P (20A) IEC C20 (20A)

Input Connector: XLR, one per channel.

Link/Out Connector: Loop-thru signal from input connector for linking to another ampli- fier, one per channel.

Output Connectors: Two Neutrik® Speakon® NL4MP (mates with NL4FC) output connec- tors. Channel-1 Speakon® is wired with Ch. 1 and Ch. 2 outputs for use with optional single 4-conductor cable. Two binding post outputs (in parallel with Speakon® connectors).

HiQnet USB Connector: Type B, connects to a HiQnet network.

Protection

XTi-Series amplifiers are protected against shorted, open or mismatched loads; over- loaded power supplies; excessive tempera- ture; chain destruction phenomena; excessive output current, input overload damage; and high-frequency blowups. They also protect loudspeakers from input/output DC, large or dangerous DC offsets and turn-on/turn-off transients.

Construction

Chassis: Steel.

Cooling: Proportional speed fan with front-to- rear airflow.

Dimensions: EIA Standard 19-in. rack mount width (EIA RS-310-B), 3.5 in. (8.9 cm) high and 12.25 in. (31.11 cm) deep behind mounting surface. XTi 6000 is 16.2 in. (41.15 cm) deep.

Net Weight:

XTi 1K, 2K, 4K: 18.5 lb (8.4 kg).

XTi 6K: 24.0 lb (10.9 kg).

Shipping Weight:

XTi 1K, 2K, 4K: 21.5 lb (9.8 kg).

XTi 6K: 30.0 lb (13.6 kg).

Optional Accessory:

Rear rack-ear support for XTi 6000.

Regulatory Certifications

Other Applications

12/08

139472-3

 

 

P O R TA B L E P A

The XTi Series of Crown® amplifiers are professional tools designed and built for portable PA applica- tions. The series includes four models which are similar except for output power: XTi 1000, 2000, 4000 and 6000. All are rugged and lightweight, and offer unmatched value in their class. XTi-Series amplifiers feature an LCD screen with speaker presets for crossover frequencies, EQ, limiting, delay, and a subharmonic synthesizer. Other features include a switch-mode universal power supply, useful function indicators, proportional-speed fan-assisted cooling, XLR inputs, Speakon® and binding-post

outputs, short-circuit protection and more.

Page 32 Page 34
Image 33
Page 32 Page 34
Contents Crown Power Amplifiers Page Installed Sound 200W 1,200W 1,200W‡ 000W250W Back Panel Controls and Connectors Front Panel Controls and IndicatorsOptions Protection Systems220W † Operation per channel-pair 100V direct outputs220W 250W † 440WVoltage Gain at maximum level setting, 1.4V sensitivity CobraNet audio Analog audio inputs allow CobraNet network audio input260W 180W 270W 220WSwitches GeneralOverall Audio Performance 500W Configuration with HiQnetImpedances and outputs 200W 650WRear Panel Controls and Connectors Included AccessoriesPerformance ProtectionOne-touch Performance Signal to Noise Ratio below rated 8-ohm power at 1 kHz Regulatory CertificationsAC Line Current Page Commercial Audio Adaptable Weight DimensionsOr 2 inputs 1 to 2 amplifier output channels Power ZoneOptional Accessories Shipping WeightCooling 60W ChannelAC Voltage Tolerance +10%/-20% Crosstalk all controls at 10 -70 dB at 1kHz Load ImpedanceAny input can be sent to any output Priority muting PracticalStorage Temperature -20 C to 85 C THD Less than 0.5% at rated power at 1 kHzAmp Config Switch a DIP switch with two functions Input Sensitivity for full output at maximum gain135MA, 160MA Back Panel Controls, Connectors and Indicators 40W Music & PagingActive Indicator Illuminates when VOX ducking is active THD 0.5% at rated power at 1 kHzVcap remote volume control 22 lb 9.98 kgSingle-zone XM EnabledOutput Volume Control Detented potentiometer with knob Active Indicator LED illuminates when VOX ducking is activeTEL Input Connector Transformer-isolated Page Portable PA 200W 000W World-Class600W 100WHiQnet USB Connector Type B, connects to a HiQnet network Optional AccessoryVoltage Gain at 1kHz, 8 ohm rated output 050W InnovationControls IndicatorsPureBandTM Crossover System Input/OutputEvolution 500W ‡000W ‡ Shipping Weight 74.0 lb 33.6 kg Page Touring 250W 000W High power density, up to 9000 watts in a 2U chassis500W 600W 000W 100W 500W 000WSummary Specifications Front Panel Indicators, Controls and ConnectorsBack Panel Connectors, Controls, and Indicators Macro-Tech i Series The Legend Continues Firmware/Software Back Panel Controls, Indicators and ConnectorsPage Recording & Broadcast Tried & True 50W110W 80W Frequency Response ±0.1 dB from 20 Hz to 20 kHz at 1watt Output SignalPage Cinema 450W N E M a Performance Monitor IEC AC Power Receptacle Connects to an CTs 2-Channel 260W 180W 220W CTs Multi-ChannelPage Networked Products & Accessories SmartAmp Automation for TCP/IQ SmartAmp Automation for Networked AudioOperation and helps to save both time and money Ethernet networkPIP USP4 Remote Level Control Wall-Mount ControllersChoosing the Right Module 170V Constant-Voltage TransformerCommercial Audio Accessories Accessories3PLUS3 3+3 Extended Warranty Cover your ampPage Product Applications & Warranty Page Page Accessories & Applications LIVE Sound Product Applications Crown Amplifier Warranty WORLDWIDE­EXCEPT USA & CANADA Summary of Warranty

CTS 600, CTS 1200, CTS 2000, CTS 3000 specifications

Crown, a leading name in material handling equipment, has developed the Crown CTS series, which includes the CTS 3000, CTS 2000, CTS 600, and CTS 1200 models. Each of these rugged machines is designed to enhance productivity and efficiency in various warehouse and distribution applications, integrating innovative technologies and robust features.

The Crown CTS 3000 is the flagship model in this series, designed for high-demand environments that require exceptional lifting capability. It boasts a powerful AC drive system that offers superior acceleration and speed control, providing operators with smooth and responsive handling. The heightened visibility from the operator's compartment minimizes blind spots, enhancing safety and efficiency during operations. The CTS 3000 also features advanced battery management technology, allowing for prolonged operation and minimal downtime.

Next in line is the Crown CTS 2000, which is tailored for a range of medium-duty applications. While its lifting capacity is slightly lower than the CTS 3000, it incorporates many similar functionalities. It features a user-friendly control interface, making it easy for operators of any skill level to manage tasks efficiently. The robust design ensures reliability and durability, making it an excellent choice for businesses that require consistent performance under moderately demanding conditions.

The Crown CTS 600 model is specially designed for light-duty operations. Ideal for shorter runs and smaller spaces, the CTS 600 is compact and maneuverable without compromising on performance. It comes equipped with advanced safety features, including an integrated operator presence system that ensures safe operation. The model’s light weight also translates into better battery efficiency, making it a cost-effective option for businesses seeking to optimize their operational expenses.

Lastly, the Crown CTS 1200 is a versatile model that strikes a balance between power and agility. It is particularly suitable for environments where space is at a premium. The CTS 1200 is engineered for versatility, allowing it to handle a variety of loads with ease. It features intuitive controls and exceptional ergonomics, contributing to operator comfort during long shifts. This model also emphasizes energy efficiency and reduced environmental impact through its advanced power management system.

In summary, the Crown CTS series offers a range of models catering to varying operational needs, from high-demand environments with the CTS 3000 to the space-saving capabilities of the CTS 600. Each model is built upon a foundation of advanced technologies that promote safety, efficiency, and productivity, making them indispensable tools in today's material handling landscape.
Top Page Image Contents