GTO 2502, 2550 installation manual Installation of the Closed Position Stops, Slave Gate

Page 21

Installation of the Closed Position Stops

The GTO/PRO Gate Openers firmly hold the gates in the closed position using positive stops. The positive stops help stabilize the gate leaves in the closed position. To further enhance stability and security, we strongly recommended using an optional GTO/PRO Automatic Gate Lock (see Accessory Catalog) with your dual gate.

IMPORTANT: You need to determine which side of the driveway you will mount the control box. From this point on the gate and gate opener on the same side as the control box will be referred to as the MASTER gate and gate opener. The gate and gate opener on the opposite side of the driveway from the control box will be referred to as the SLAVE gate and gate opener.

 

 

 

 

 

 

 

Gate Hinge

Optional Ground Stop

Gate Hinge

 

 

 

 

 

 

 

 

(beneath gate)

 

 

 

 

 

 

 

 

MASTER GATE

 

 

 

SLAVE GATE

 

 

 

 

 

 

 

 

 

Closed Position 

 

 

 

CONTROL BOX

 

Stop Plates

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

The gate leaf can open

 

 

 

The gate leaf can open

 

 

 

 

 

 

 

up to 110˚ (max.)

 

 

 

up to 110˚ (max.)

Step 1

Attach the horizontal closed position stop plate to the MASTER gate leaf.

Closed Position Stop Plate mounted  horizontally on metal post with U-bolts.

Detach the gate operators from the gates and move the gates to their closed position (Illustration A). Using appropriate hardware for your type of gate (U-bolts for tube or chain link; screw or bolts for wood or metal) attach the closed position stop plate (horizontally) about mid height on the MASTER gate frame. Do not tighten it completely at this time. Slide the stop plate toward the frame of the SLAVE gate leaf until they touch (Illustration B). Once you have moved the stop plate to the correct position, tighten its hardware completely.

FRONT VIEW

MASTER Gate Frame

SLAVE Gate Frame

Illustration B

TOP VIEW

 

NOTE: The optional ground stop post is used to provide a secure point for the SLAVE gate to close against. If you will be using the GTO/PRO Horizontal Gate Lock accessory with your gate opener system, the closed position ground stop is REQUIRED, as shown in Steps 2 and 3 on the next page.

17

Page 20 Page 22
Image 21
Page 20 Page 22
Contents Installation Manual for Place of Purchase When You Know Multiply By To Find SymbolTable of Contents Please Read this First Switch is OFF and the gate is not moving Important Safety InstructionsFor The Consumer II. During Installation III. After Installation Secondary Means of Protection Against Entrapment Entrapment Alarm UL 325 30A.1.1ARequired Safety Precautions for Gates Install Warning SignsEntrapment Protection DC 2500 Series Opener and Mounting Hardware Dual Gate Opener Parts ListTools Needed Control Box and Electrical ComponentsTechnical Specifications Preparation of the Gate Installation OverviewRecommended Reinforcement Examples Installation of Mounting HardwarePost Bracket Assembly Closed Position Installing the Post Bracket Assembly and Gate Than 6, threaded rods orCarriage bolts longer than Mounting the First Opener Installing the Second OpenerSlave Gate Installation of the Closed Position StopsGround stop needs to be positioned near the end Mounting the Control Box Connecting Opener Power Cables Master OperatorSlave Operator Optional Solar Panels and Gate Activity Installation of the TransformerImportant Information about LOW Voltage Wire Make sure the exposed wires do not touch each other Main DIP Switch Settings Modes DIP SwitchesDIP Switches #1 and #2 Factory Set OFF/OFF Dual Gate DIP Switch Settings Dual ModesDIP Switch #3 Additional Delay Factory Set OFF #4 on to set or ClearYour GTO/PRO has two Limit Settings Setting the Closed Position LimitsRemove the Transmitter Cover Set the transmitter DIP SwitchesTeach the New Code to Control Board Memory Release Learn Transmitter buttonObstruction Sensitivity Potentiometer Installing the ReceiverRun the cable through PVC conduit to protect it from damage Do not mount upside downConnecting Additional Safety Devices Contact Sensors safety edgesIf not installing a contact sensor skip to next section If not installing a shadow loop skip to next section If not installing a non-contact sensor skip to next sectionNon-Contact Sensors photo beams Shadow LoopIf not connecting accessories skip to next section Connecting AccessoriesSwinging gates shall not open into public access areas Push to Open InstallationSetting the Open Position Limit Maintenance Troubleshooting Guide Diagnostic LEDs GTO/PRO, 3121 Hartsfield Road, Tallahassee, Florida, USA Repair ServiceMASONRY, BRICK, or Rock etc. Columns Column Installation InformationSolar Panel FM123, FM122 Wireless Entry Intercom / Keypad FM136Push Button Control RB101 Pin Lock FM345Replacement Battery RB500

2502, 2550 specifications

The GTO 2502 and GTO 2550 are advanced machine models recognized for their high efficiency and performance in various industrial applications. Designed with modern manufacturing needs in mind, these machines exemplify technological innovation and superior engineering.

The GTO 2502 model is designed for remarkable precision and reliability. It operates with an emphasis on energy efficiency, minimizing power consumption without sacrificing performance. The machine is equipped with a cutting-edge control system that simplifies operation and enhances the user experience. This control system includes a user-friendly interface, allowing operators to monitor performance metrics easily and optimize settings in real time.

On the other hand, the GTO 2550 takes efficiency and productivity a step further. This model boasts an extended operational range and supports a wider variety of materials, making it a versatile choice for manufacturers in different sectors. The GTO 2550 is engineered with upgraded components to enhance speed and durability, ensuring that it can handle demanding workloads day in and day out.

Both models incorporate advanced technologies such as real-time monitoring and diagnostics, enabling users to predict maintenance needs and reduce downtime. Their robust construction ensures longevity, making them a worthwhile investment for businesses looking to improve their operational efficiency.

Another key feature of the GTO 2502 and GTO 2550 is their modular design, which allows for easy upgrades and scalability. This means businesses can adapt to changing production demands without the need for entirely new machines. Furthermore, both models are equipped with eco-friendly technologies, helping companies reduce their carbon footprint while maintaining high production levels.

In summary, the GTO 2502 and GTO 2550 are designed to meet the high standards of modern manufacturing with their advanced features and technologies. They offer a combination of precision, efficiency, and adaptability that is essential in today’s competitive market. As industries continue to evolve, these models stand out as prime examples of innovation in machinery design, making them invaluable assets for any manufacturing operation.
Top Page Image Contents