GTO 2550, 2502 installation manual Replacement Battery RB500

Page 44

ACCESSORIES

Replacement Battery (RB500)

Standard 12 volt, 7.0 amp-hour, maintenance-free battery for the GTO/PRO SW-2000, GTO/PRO SW-2502, GTO/PRO SW-3000, GTO/PRO SW-4000gate operator systems. This is the only battery approved for use with the GTO/PRO gate operator systems. Life expectancy is 3-5 years.

Low Voltage Wire (RB509)

The 16 gauge, multi-stranded, dual conductor Low Voltage Wire is for connecting the AC powered transformer, or the Solar Panel to the control board. Also used for the connection of accessories, such as locks, keypads, push buttons and other wired control devices. This specially designed wire is UV treated, PVC coated and ready for direct burial. Available in 1000' rolls or special lengths.

Push to Open Bracket (347 IH)

Required when GTO/PRO SW-2502gate operator(s) must push the gate open, such as on a sloping driveway or where space prevents gate(s) from opening inward (pulled open). Order two PTO brackets for conversion of a dual

swing gate installation.

Column Mount Lock Receiver (433IH)

For mounting the Automatic Gate Lock on brick columns, walls, or for other applications with limited space between gate and post.

Replacement Transformer (RB570)

Standard 18 volt AC transformer for maintaining the battery included with the GTO/PRO SW-2502gate operator. This is the only transformer approved for use with all UL325 GTO/PRO gate operator systems.

Garage Door Receiver (RB709)

The Garage Door Receiver allows you to use the same GTO/PRO entry transmitter (see Dual and Triple Transmitters) to operate your gate operator and your garage door operator. Compatible with most garage door operators.

Dual & Triple Button Transmitters (RB742 & RB743)

The Dual (RB742) & Triple (RB743) Button Transmitters are for remote control of multiple separate gate operators, and/or gate operator(s) and garage door operator(s) (see Garage Door Receiver). 9 Volt battery included.

If you have a question about any special order item,

just call 1-800-543-GATE!

The contents of all material available on this installation manual are copyrighted by GTO, Inc. (“GTO”), unless otherwise indicated. All rights are reserved by GTO, and content may not be reproduced,

downloaded, disseminated, published, or transferred in any form or by any means, except with the prior, written permission of GTO, Inc. Any reprinting of GTO publications is by permission only. Copyright

infringement is a violation of federal law.

GTO/PRO, GTO/PRO are registered trademarks of GTO, Inc. and are the exclusive property of GTO, Inc. (“GTO”).

All rights are reserved by GTO, Inc., and these marks may not be used, in any for without the prior, written permission of GTO, Inc.

3121 Hartsfield Road • Tallahassee, Florida, USA 32303 • (850) 575-0176 • Fax (850) 575-8912

Web site www.gtopro.com

40

Page 43 Page 44
Image 44
Page 43 Page 44
Contents Installation Manual for When You Know Multiply By To Find Symbol Place of PurchaseTable of Contents Please Read this First Important Safety Instructions Switch is OFF and the gate is not movingFor The Consumer II. During Installation III. After Installation Entrapment Alarm UL 325 30A.1.1A Secondary Means of Protection Against EntrapmentEntrapment Protection Required Safety Precautions for GatesInstall Warning Signs DC 2500 Series Dual Gate Opener Parts List Opener and Mounting HardwareControl Box and Electrical Components Tools NeededTechnical Specifications Installation Overview Preparation of the GateInstallation of Mounting Hardware Recommended Reinforcement ExamplesPost Bracket Assembly Closed Position Carriage bolts longer than Installing the Post Bracket Assembly and GateThan 6, threaded rods or Installing the Second Opener Mounting the First OpenerInstallation of the Closed Position Stops Slave GateGround stop needs to be positioned near the end Mounting the Control Box Slave Operator Connecting Opener Power CablesMaster Operator Installation of the Transformer Optional Solar Panels and Gate ActivityImportant Information about LOW Voltage Wire Make sure the exposed wires do not touch each other DIP Switches Main DIP Switch Settings ModesDual Gate DIP Switch Settings Dual Modes DIP Switches #1 and #2 Factory Set OFF/OFFDIP Switch #3 Additional Delay Factory Set OFF #4 on to set or ClearSetting the Closed Position Limits Your GTO/PRO has two Limit SettingsSet the transmitter DIP Switches Remove the Transmitter CoverTeach the New Code to Control Board Memory Release Learn Transmitter buttonInstalling the Receiver Obstruction Sensitivity PotentiometerRun the cable through PVC conduit to protect it from damage Do not mount upside downIf not installing a contact sensor skip to next section Connecting Additional Safety DevicesContact Sensors safety edges If not installing a non-contact sensor skip to next section If not installing a shadow loop skip to next sectionNon-Contact Sensors photo beams Shadow LoopConnecting Accessories If not connecting accessories skip to next sectionPush to Open Installation Swinging gates shall not open into public access areasSetting the Open Position Limit Maintenance Troubleshooting Guide Diagnostic LEDs Repair Service GTO/PRO, 3121 Hartsfield Road, Tallahassee, Florida, USAColumn Installation Information MASONRY, BRICK, or Rock etc. ColumnsWireless Entry Intercom / Keypad FM136 Solar Panel FM123, FM122Push Button Control RB101 Pin Lock FM345Replacement Battery RB500

2502, 2550 specifications

The GTO 2502 and GTO 2550 are advanced machine models recognized for their high efficiency and performance in various industrial applications. Designed with modern manufacturing needs in mind, these machines exemplify technological innovation and superior engineering.

The GTO 2502 model is designed for remarkable precision and reliability. It operates with an emphasis on energy efficiency, minimizing power consumption without sacrificing performance. The machine is equipped with a cutting-edge control system that simplifies operation and enhances the user experience. This control system includes a user-friendly interface, allowing operators to monitor performance metrics easily and optimize settings in real time.

On the other hand, the GTO 2550 takes efficiency and productivity a step further. This model boasts an extended operational range and supports a wider variety of materials, making it a versatile choice for manufacturers in different sectors. The GTO 2550 is engineered with upgraded components to enhance speed and durability, ensuring that it can handle demanding workloads day in and day out.

Both models incorporate advanced technologies such as real-time monitoring and diagnostics, enabling users to predict maintenance needs and reduce downtime. Their robust construction ensures longevity, making them a worthwhile investment for businesses looking to improve their operational efficiency.

Another key feature of the GTO 2502 and GTO 2550 is their modular design, which allows for easy upgrades and scalability. This means businesses can adapt to changing production demands without the need for entirely new machines. Furthermore, both models are equipped with eco-friendly technologies, helping companies reduce their carbon footprint while maintaining high production levels.

In summary, the GTO 2502 and GTO 2550 are designed to meet the high standards of modern manufacturing with their advanced features and technologies. They offer a combination of precision, efficiency, and adaptability that is essential in today’s competitive market. As industries continue to evolve, these models stand out as prime examples of innovation in machinery design, making them invaluable assets for any manufacturing operation.
Top Page Image Contents