GTO 2502, 2550 installation manual Post Bracket Assembly

Page 17

Determining the Mounting Position

of the Post Bracket Assembly and the Gate Bracket

Step 3

Insert the 3/8" x 2" bolt through the center hole of the post brackets and post pivot bracket

as shown. Fasten a 3/8" lock

washer, 3/8" washer and 3/8" nut on the end of the bolt. DO NOT overtighten the nut because the post pivot bracket will have to be adjusted later.

Step 4

Post Bracket Assembly

3/8" x 2" Bolt

Post Bracket

Post Pivot Bracket

Post Bracket

3/8" Washer

3/8" Lock Washer

3/8" Nut

NOTE: The following steps are intended for pull-to-opengate installations. If you are mounting your opener on a push-to-open gate (e.g., a gate on a sloped driveway) you will need to purchase a Push To Open bracket (see Accessory catalog). Also, see Push-to-Open Installation beginning on page 30.

Attach post bracket assembly and gate bracket to the opener with the clevis pins and bushings. Secure the clevis pins with hairpin clips.

Clevis Pin

Rear Mount

Bushing

Opener

Hairpin Clip

Post Bracket Assembly

Front Mount

Clevis Pin

Gate Bracket

Bushing

Hairpin Clip

Step 5

With the gate in the open position (up to 110º from its closed position), and the opener fully retracted, adjust the post bracket assembly and gate bracket until the opener is level. While holding the opener level, use C-clamps to temporarily keep the post bracket assembly and gate bracket in their respective positions on the fence post and gate.

Post Bracket Assembly

 

Level Opener

 

Gate In Open Position 

Gate Bracket

 

Fence Post

 

13

 

Page 16 Page 18
Image 17
Page 16 Page 18
Contents Installation Manual for Place of Purchase When You Know Multiply By To Find SymbolTable of Contents Please Read this First Switch is OFF and the gate is not moving Important Safety InstructionsFor The Consumer II. During Installation III. After Installation Secondary Means of Protection Against Entrapment Entrapment Alarm UL 325 30A.1.1AEntrapment Protection Required Safety Precautions for GatesInstall Warning Signs DC 2500 Series Opener and Mounting Hardware Dual Gate Opener Parts ListTools Needed Control Box and Electrical ComponentsTechnical Specifications Preparation of the Gate Installation OverviewRecommended Reinforcement Examples Installation of Mounting HardwarePost Bracket Assembly Closed Position Carriage bolts longer than Installing the Post Bracket Assembly and GateThan 6, threaded rods or Mounting the First Opener Installing the Second OpenerSlave Gate Installation of the Closed Position StopsGround stop needs to be positioned near the end Mounting the Control Box Slave Operator Connecting Opener Power CablesMaster Operator Optional Solar Panels and Gate Activity Installation of the TransformerImportant Information about LOW Voltage Wire Make sure the exposed wires do not touch each other Main DIP Switch Settings Modes DIP SwitchesDIP Switches #1 and #2 Factory Set OFF/OFF Dual Gate DIP Switch Settings Dual ModesDIP Switch #3 Additional Delay Factory Set OFF #4 on to set or ClearYour GTO/PRO has two Limit Settings Setting the Closed Position LimitsRemove the Transmitter Cover Set the transmitter DIP SwitchesTeach the New Code to Control Board Memory Release Learn Transmitter buttonObstruction Sensitivity Potentiometer Installing the ReceiverRun the cable through PVC conduit to protect it from damage Do not mount upside downIf not installing a contact sensor skip to next section Connecting Additional Safety DevicesContact Sensors safety edges If not installing a shadow loop skip to next section If not installing a non-contact sensor skip to next sectionNon-Contact Sensors photo beams Shadow LoopIf not connecting accessories skip to next section Connecting AccessoriesSwinging gates shall not open into public access areas Push to Open InstallationSetting the Open Position Limit Maintenance Troubleshooting Guide Diagnostic LEDs GTO/PRO, 3121 Hartsfield Road, Tallahassee, Florida, USA Repair ServiceMASONRY, BRICK, or Rock etc. Columns Column Installation InformationSolar Panel FM123, FM122 Wireless Entry Intercom / Keypad FM136Push Button Control RB101 Pin Lock FM345Replacement Battery RB500

2502, 2550 specifications

The GTO 2502 and GTO 2550 are advanced machine models recognized for their high efficiency and performance in various industrial applications. Designed with modern manufacturing needs in mind, these machines exemplify technological innovation and superior engineering.

The GTO 2502 model is designed for remarkable precision and reliability. It operates with an emphasis on energy efficiency, minimizing power consumption without sacrificing performance. The machine is equipped with a cutting-edge control system that simplifies operation and enhances the user experience. This control system includes a user-friendly interface, allowing operators to monitor performance metrics easily and optimize settings in real time.

On the other hand, the GTO 2550 takes efficiency and productivity a step further. This model boasts an extended operational range and supports a wider variety of materials, making it a versatile choice for manufacturers in different sectors. The GTO 2550 is engineered with upgraded components to enhance speed and durability, ensuring that it can handle demanding workloads day in and day out.

Both models incorporate advanced technologies such as real-time monitoring and diagnostics, enabling users to predict maintenance needs and reduce downtime. Their robust construction ensures longevity, making them a worthwhile investment for businesses looking to improve their operational efficiency.

Another key feature of the GTO 2502 and GTO 2550 is their modular design, which allows for easy upgrades and scalability. This means businesses can adapt to changing production demands without the need for entirely new machines. Furthermore, both models are equipped with eco-friendly technologies, helping companies reduce their carbon footprint while maintaining high production levels.

In summary, the GTO 2502 and GTO 2550 are designed to meet the high standards of modern manufacturing with their advanced features and technologies. They offer a combination of precision, efficiency, and adaptability that is essential in today’s competitive market. As industries continue to evolve, these models stand out as prime examples of innovation in machinery design, making them invaluable assets for any manufacturing operation.
Top Page Image Contents