GTO 2550, 2502 installation manual Please Read this First

Page 4

PLEASE READ THIS FIRST!

Thank you for purchasing a GTO/PRO-SW2502When correctly installed and properly used, your GTO/PRO- SW2502 Operator will give you many years of reliable service. Please read the following information to ensure you have the correct system for your particular needs. This manual will enable you to properly install your GTO/PRO- SW2502 Automatic Gate Operator.

The GTO/PRO-SW2502 Operator is designed for installation on pull-to-open gates (gates that open into the property). By purchasing an accessory bracket, the GTO/PRO-SW2502 Operator can accommodate push-to-open gates (gates that open out from the property). The gates must not exceed 16 feet in length (per leaf) nor weigh more than 500 pounds (per leaf) (please see Technical Specifications on page 10). The GTO/PRO-SW2502 Operator can be used on vinyl, aluminum, chain link, farm tube, and wrought iron gates. Use on solid (wood) gates is not recommended. Solid surface gates have a high resistance to the wind. If the wind is strong enough, the operator will obstruct and stop.

The GTO/PRO-SW2502 Operator accommodates extra transmitters, digital keypads, solar panels, push buttons, automatic gate locks, and other access control products. These optional accessories (see the enclosed GTO/PRO Accessory Catalog) are available.

The GTO/PRO-SW2502 Operator features adjustable obstruction sensing. This safety feature makes the gate stop and reverse direction within 2 seconds when it comes in contact with an obstruction. MIN is the factory setting; meaning the gate will exert the minimum force on an obstruction before it stops and reverses direction.

The GTO/PRO-SW2502 Operator also has an adjustable auto-close feature. After the gate reaches the fully open position, it can be set to remain open up to 120 seconds before automatically closing. Pressing the transmitter button at any time after the gate opens fully will cause it to close immediately. OFF is the factory setting; meaning the gate will stay open until you press the transmitter (or keypad, etc.) again.

Please call GTO/PRO at (800) 543-GATE [4283] or (850) 575-0176 for more information about our GTO/PRO professional line of gate operators and accessories. Our Sales Department will be glad to give you the name and phone number of a GTO/PRO dealer near you.

iii

Page 3 Page 5
Image 4
Page 3 Page 5
Contents Installation Manual for When You Know Multiply By To Find Symbol Place of PurchaseTable of Contents Please Read this First Important Safety Instructions Switch is OFF and the gate is not movingFor The Consumer II. During Installation III. After Installation Entrapment Alarm UL 325 30A.1.1A Secondary Means of Protection Against EntrapmentInstall Warning Signs Required Safety Precautions for GatesEntrapment Protection DC 2500 Series Dual Gate Opener Parts List Opener and Mounting HardwareControl Box and Electrical Components Tools NeededTechnical Specifications Installation Overview Preparation of the GateInstallation of Mounting Hardware Recommended Reinforcement ExamplesPost Bracket Assembly Closed Position Than 6, threaded rods or Installing the Post Bracket Assembly and GateCarriage bolts longer than Installing the Second Opener Mounting the First OpenerInstallation of the Closed Position Stops Slave GateGround stop needs to be positioned near the end Mounting the Control Box Master Operator Connecting Opener Power CablesSlave Operator Installation of the Transformer Optional Solar Panels and Gate ActivityImportant Information about LOW Voltage Wire Make sure the exposed wires do not touch each other DIP Switches Main DIP Switch Settings ModesDual Gate DIP Switch Settings Dual Modes DIP Switches #1 and #2 Factory Set OFF/OFFDIP Switch #3 Additional Delay Factory Set OFF #4 on to set or ClearSetting the Closed Position Limits Your GTO/PRO has two Limit SettingsSet the transmitter DIP Switches Remove the Transmitter CoverTeach the New Code to Control Board Memory Release Learn Transmitter buttonInstalling the Receiver Obstruction Sensitivity PotentiometerRun the cable through PVC conduit to protect it from damage Do not mount upside downContact Sensors safety edges Connecting Additional Safety DevicesIf not installing a contact sensor skip to next section If not installing a non-contact sensor skip to next section If not installing a shadow loop skip to next sectionNon-Contact Sensors photo beams Shadow LoopConnecting Accessories If not connecting accessories skip to next sectionPush to Open Installation Swinging gates shall not open into public access areasSetting the Open Position Limit Maintenance Troubleshooting Guide Diagnostic LEDs Repair Service GTO/PRO, 3121 Hartsfield Road, Tallahassee, Florida, USAColumn Installation Information MASONRY, BRICK, or Rock etc. ColumnsWireless Entry Intercom / Keypad FM136 Solar Panel FM123, FM122Push Button Control RB101 Pin Lock FM345Replacement Battery RB500

2502, 2550 specifications

The GTO 2502 and GTO 2550 are advanced machine models recognized for their high efficiency and performance in various industrial applications. Designed with modern manufacturing needs in mind, these machines exemplify technological innovation and superior engineering.

The GTO 2502 model is designed for remarkable precision and reliability. It operates with an emphasis on energy efficiency, minimizing power consumption without sacrificing performance. The machine is equipped with a cutting-edge control system that simplifies operation and enhances the user experience. This control system includes a user-friendly interface, allowing operators to monitor performance metrics easily and optimize settings in real time.

On the other hand, the GTO 2550 takes efficiency and productivity a step further. This model boasts an extended operational range and supports a wider variety of materials, making it a versatile choice for manufacturers in different sectors. The GTO 2550 is engineered with upgraded components to enhance speed and durability, ensuring that it can handle demanding workloads day in and day out.

Both models incorporate advanced technologies such as real-time monitoring and diagnostics, enabling users to predict maintenance needs and reduce downtime. Their robust construction ensures longevity, making them a worthwhile investment for businesses looking to improve their operational efficiency.

Another key feature of the GTO 2502 and GTO 2550 is their modular design, which allows for easy upgrades and scalability. This means businesses can adapt to changing production demands without the need for entirely new machines. Furthermore, both models are equipped with eco-friendly technologies, helping companies reduce their carbon footprint while maintaining high production levels.

In summary, the GTO 2502 and GTO 2550 are designed to meet the high standards of modern manufacturing with their advanced features and technologies. They offer a combination of precision, efficiency, and adaptability that is essential in today’s competitive market. As industries continue to evolve, these models stand out as prime examples of innovation in machinery design, making them invaluable assets for any manufacturing operation.
Top Page Image Contents