GTO 2550, 2502 installation manual For The Consumer

Page 6

IMPORTANT SAFETY INSTRUCTIONS

For The Consumer

WARNING: To reduce the risk of injury or death:

1.READ AND FOLLOW ALL INSTRUCTIONS. Failure to meet the requirements set forth in the instruction manual could cause severe injury and/or death, for which the manufacturer cannot be held responsible.

2.When designing a system that will be entered from a highway or main thoroughfare, make sure the system is placed far enough from the road to prevent traffic congestion.

3.The gate must be installed in a location that provides adequate clearance between it and adjacent structures when opening and closing to reduce the risk of entrapment. Swinging gates must not open into public access areas.

4.The gate and gate opener installation must comply with any applicable local codes.

I. Before Installation

1.Verify this dual opener is proper for the type and size of gate, its frequency of use and the proper class rating.

2.Make sure the dual gate has been properly installed and swings freely in both directions. Repair or replace all worn or damaged gate hardware prior to installation. A freely moving gate will require less force to operate and will enhance the performance of the opener and safety devices used with the system.

3.Review the operation of the system to become familiar with its safety features. Understand how to disconnect the opener for manual gate operation (see page 1).

4.This gate opener is intended for vehicular gates ONLY. A separate entrance or gate must be installed for pedestrian use (see page 6).

5.Always keep people and objects away from the gate and its area of travel. NO ONE SHOULD CROSS THE

PATH OF A MOVING GATE.

6.Pay close attention to the diagram below and be aware of these areas at all times.

 

ZONE 1

 

ZONE 2

 

ZONE 2

ZONE 5

 

ZONE 5

ZONE 3

 

ZONE 3

ZONE 4

Driveway

ZONE 4

Gate in the 

Entrapment Zones for a

Gate in the 

Open Position

Open Position

Pull-To-Open Application

2

Page 5 Page 7
Image 6
Page 5 Page 7
Contents Installation Manual for When You Know Multiply By To Find Symbol Place of PurchaseTable of Contents Please Read this First Important Safety Instructions Switch is OFF and the gate is not movingFor The Consumer II. During Installation III. After Installation Entrapment Alarm UL 325 30A.1.1A Secondary Means of Protection Against EntrapmentRequired Safety Precautions for Gates Install Warning SignsEntrapment Protection DC 2500 Series Dual Gate Opener Parts List Opener and Mounting HardwareControl Box and Electrical Components Tools NeededTechnical Specifications Installation Overview Preparation of the GateInstallation of Mounting Hardware Recommended Reinforcement ExamplesPost Bracket Assembly Closed Position Installing the Post Bracket Assembly and Gate Than 6, threaded rods orCarriage bolts longer than Installing the Second Opener Mounting the First OpenerInstallation of the Closed Position Stops Slave GateGround stop needs to be positioned near the end Mounting the Control Box Connecting Opener Power Cables Master OperatorSlave Operator Installation of the Transformer Optional Solar Panels and Gate ActivityImportant Information about LOW Voltage Wire Make sure the exposed wires do not touch each other DIP Switches Main DIP Switch Settings ModesDIP Switch #3 Additional Delay Factory Set OFF Dual Gate DIP Switch Settings Dual ModesDIP Switches #1 and #2 Factory Set OFF/OFF #4 on to set or ClearSetting the Closed Position Limits Your GTO/PRO has two Limit SettingsTeach the New Code to Control Board Memory Set the transmitter DIP SwitchesRemove the Transmitter Cover Release Learn Transmitter buttonRun the cable through PVC conduit to protect it from damage Installing the ReceiverObstruction Sensitivity Potentiometer Do not mount upside downConnecting Additional Safety Devices Contact Sensors safety edgesIf not installing a contact sensor skip to next section Non-Contact Sensors photo beams If not installing a non-contact sensor skip to next sectionIf not installing a shadow loop skip to next section Shadow LoopConnecting Accessories If not connecting accessories skip to next sectionPush to Open Installation Swinging gates shall not open into public access areasSetting the Open Position Limit Maintenance Troubleshooting Guide Diagnostic LEDs Repair Service GTO/PRO, 3121 Hartsfield Road, Tallahassee, Florida, USAColumn Installation Information MASONRY, BRICK, or Rock etc. ColumnsPush Button Control RB101 Wireless Entry Intercom / Keypad FM136Solar Panel FM123, FM122 Pin Lock FM345Replacement Battery RB500

2502, 2550 specifications

The GTO 2502 and GTO 2550 are advanced machine models recognized for their high efficiency and performance in various industrial applications. Designed with modern manufacturing needs in mind, these machines exemplify technological innovation and superior engineering.

The GTO 2502 model is designed for remarkable precision and reliability. It operates with an emphasis on energy efficiency, minimizing power consumption without sacrificing performance. The machine is equipped with a cutting-edge control system that simplifies operation and enhances the user experience. This control system includes a user-friendly interface, allowing operators to monitor performance metrics easily and optimize settings in real time.

On the other hand, the GTO 2550 takes efficiency and productivity a step further. This model boasts an extended operational range and supports a wider variety of materials, making it a versatile choice for manufacturers in different sectors. The GTO 2550 is engineered with upgraded components to enhance speed and durability, ensuring that it can handle demanding workloads day in and day out.

Both models incorporate advanced technologies such as real-time monitoring and diagnostics, enabling users to predict maintenance needs and reduce downtime. Their robust construction ensures longevity, making them a worthwhile investment for businesses looking to improve their operational efficiency.

Another key feature of the GTO 2502 and GTO 2550 is their modular design, which allows for easy upgrades and scalability. This means businesses can adapt to changing production demands without the need for entirely new machines. Furthermore, both models are equipped with eco-friendly technologies, helping companies reduce their carbon footprint while maintaining high production levels.

In summary, the GTO 2502 and GTO 2550 are designed to meet the high standards of modern manufacturing with their advanced features and technologies. They offer a combination of precision, efficiency, and adaptability that is essential in today’s competitive market. As industries continue to evolve, these models stand out as prime examples of innovation in machinery design, making them invaluable assets for any manufacturing operation.
Top Page Image Contents