Fujitsu P42VHA20E, P-TE1000E, P-TE1010E, P42HHA10E Installation, Connecting the signal input cable

Page 43

INSTALLATION

1. Turn the power supply switch to OFF.

2.Remove the power plug from outlet.

3.Remove the plate attached to the bottom rear of the main unit from

the Video board unit mounting bracket (3 mm screw w/spring X 3).

4. Insert the Video board unit into the main unit slot using the guides on the sides.

5.Completely insert the Video board until the plate touches the main unit box.

6. Mount the plate using the 3 screws with spring removed earlier.

7. Affix the enclosed connector label to the marking position on the rear cover.

Connecting the signal input cable

For details, see “Connecting to External Equipment” in the main unit instructions manual.

CAUTION: Follow the items given below, to prevent accidental injuries and possible electrical shock.

Turn off the power supply and disconnect the power plug from outlet before installing the Video board unit. Do not remove the cabinet when installing the Video board unit.

Do not remove screws expect for the specified user service screw marked “ ”.

Do not use screws other than that specified in this manual for the installation of this Video board unit.

English

Downloaded From TV-Manual.com Manuals

E-43

Image 43

Contents USER’S Manual Important Safety Instructions Safety PrecautionsImportant Information Power cord Power supply voltage Features Information AccessoriesChecking Accessories Handy TipsReference InstallationDisplay Section Front Part Names and FunctionsControl Panel Right side of display Videoboard Display Section Lower PartPin No Signal Pin No Input signalDescription of Input Terminals Remote Control Putting Batteries in the Remote Control Using the Remote ControlPrecautions Display side Effective Range for the Remote ControlDisplay front Two big ferrite cores Connecting the Display to External EquipmentReceptacle Ferrite coresVCR E-15 Satellite tuner E-17 Speaker Display Speaker optional Remote controlExample of Connection to External Components VCR or other external components See PTo Scart output To Scart input VCRDVD Player Connecting the Display to External EquipmentAn example of the underside of the display Satellite TunerConnecting the Display to External Equipment Adjusting the Volume Turning the Power on and OFFBasic Operations Press the buttons to select the input mode Selecting Input ModeVideo Input Mode RGB Input ModeOn-screen information Display Picture Mode Picture ModeOther Basic Operations Convenient FunctionsWatching Pictures on the Wide Screen Switching Between Screen SizesPress to select a desired picture mode Normal mode Wide1 modeAspect Ratio Screen SizeAdjustment Menu Adjustment MenuAdjusting Pictures Picture Menu Precision Setting for more advanced adjustment Setting Picture Mode Picture ModeCase of Save Setting Noise Reduction Noise ReductionStoring the setting of Picture Picture Memory Case of LoadPOSITION/SIZE selected from the main menu screen Position adjustment screenPress To select Press Change position valuesVideo, S-video mode Comp.video mode Adjusting Screen Position PositionAdjusting Screen Size Size Setting RangePress or to select Balance Adjusting Audio Audio MenuPress To adjust Balance Press or to select AudioSetting Loudness Loudness Adjusting Treble TrebleAdjusting Bass Bass Adjusting Volume Balance BalancePress or to select Language Other Adjustments Features MenuPress or to select Features Press or to select On Screen MenuFeatures setup screen has the following 5 options AdjustmentOn Screen Menu FunctionMask Setting the Input TerminalsVideo Input when the P-TE1000E is installed Function Video FormatBNC Input Video Input when the P-TE1010E is installedBNC-Input selection screen SUB Input selection screen SUB InputDVI Input RGB-PC DecoderBlack White Other SettingsDPMSfor other than RGB1 Audio InputMinimizing phosphor burn-in Screen Orbiter For RGB Screen Orbiter setting screenDisplaying System Status Information Specifying RGB Input Signal Code Setting For RGB2, RGB3Setting Exhibition Mode Exhibition Mode Displaying white over entire screen White ScreenDisplays the message of having completed the initialization Press or to select Factory DefaultFactory Default selected in the main menu screen Press or to select the YesOptions Connecting the signal input cable InstallationDVI-D Factory SettingsModel SpecificationSpecification Problem Action Cleaning and MaintenanceHandy Tips