Fujitsu P-TE1010E Using the Remote Control, Putting Batteries in the Remote Control, Precautions

Page 11

USING THE REMOTE CONTROL

PUTTING BATTERIES IN THE REMOTE CONTROL

English

1To remove the cover, slide it outwards while pressing it down.

2Place two AA batteries in the remote control. Make sure that the batteries are properly oriented.

3Close the cover until it snaps into place.

PRECAUTIONS

To prevent malfunction, be sure not to apply any form of severe shock to the remote control.

To prevent malfunction or deformation, be sure not to allow the remote control to become wet; also, keep it away from hot locations or heating equipment.

Be sure not to clean the remote control using a cloth dampened in any volatile solvent, such as benzene or thinner.

CAUTION: Be sure to use replacement batteries of the same type as the original ones.

When disposing of used batteries, please comply with governmental regulations or environmental public institution’s rules that apply in your country/area.

Note

The remote control will not function properly if the batteries are dead. Be sure to replace them as needed.

Do not use rechargeable batteries (Ni-Cd).

Downloaded From TV-Manual.com Manuals

E-11

Image 11

Contents USER’S Manual Important Information Safety PrecautionsImportant Safety Instructions Power cord Power supply voltage Features Information AccessoriesChecking Accessories Handy TipsReference InstallationControl Panel Right side of display Part Names and FunctionsDisplay Section Front Videoboard Display Section Lower PartDescription of Input Terminals Pin No Input signalPin No Signal Remote Control Precautions Using the Remote ControlPutting Batteries in the Remote Control Display front Effective Range for the Remote ControlDisplay side Two big ferrite cores Connecting the Display to External EquipmentReceptacle Ferrite coresVCR E-15 Satellite tuner E-17 Speaker Display Speaker optional Remote controlExample of Connection to External Components VCR or other external components See PTo Scart output To Scart input VCRDVD Player Connecting the Display to External EquipmentAn example of the underside of the display Satellite TunerConnecting the Display to External Equipment Basic Operations Turning the Power on and OFFAdjusting the Volume Press the buttons to select the input mode Selecting Input ModeVideo Input Mode RGB Input ModeOn-screen information Display Picture Mode Picture ModeOther Basic Operations Convenient FunctionsWatching Pictures on the Wide Screen Switching Between Screen SizesPress to select a desired picture mode Normal mode Wide1 modeAspect Ratio Screen SizeAdjustment Menu Adjustment MenuAdjusting Pictures Picture Menu Precision Setting for more advanced adjustment Setting Picture Mode Picture ModeCase of Save Setting Noise Reduction Noise ReductionStoring the setting of Picture Picture Memory Case of LoadPOSITION/SIZE selected from the main menu screen Position adjustment screenPress To select Press Change position valuesVideo, S-video mode Comp.video mode Adjusting Screen Position PositionAdjusting Screen Size Size Setting RangePress or to select Balance Adjusting Audio Audio MenuPress To adjust Balance Press or to select AudioSetting Loudness Loudness Adjusting Treble TrebleAdjusting Bass Bass Adjusting Volume Balance BalancePress or to select Language Other Adjustments Features MenuPress or to select Features Press or to select On Screen MenuFeatures setup screen has the following 5 options AdjustmentOn Screen Menu FunctionMask Setting the Input TerminalsVideo Input when the P-TE1000E is installed Function Video FormatBNC-Input selection screen Video Input when the P-TE1010E is installedBNC Input SUB Input selection screen SUB InputDVI Input RGB-PC DecoderBlack White Other SettingsDPMSfor other than RGB1 Audio InputMinimizing phosphor burn-in Screen Orbiter For RGB Screen Orbiter setting screenDisplaying System Status Information Specifying RGB Input Signal Code Setting For RGB2, RGB3Setting Exhibition Mode Exhibition Mode Displaying white over entire screen White ScreenDisplays the message of having completed the initialization Press or to select Factory DefaultFactory Default selected in the main menu screen Press or to select the YesOptions Connecting the signal input cable InstallationDVI-D Factory SettingsModel SpecificationSpecification Handy Tips Cleaning and MaintenanceProblem Action