Teledyne HPM-2002-OBE instruction manual Manual Print History

Page 2

Manual Print History

The print history shown below lists the printing dates of all revisions and addenda created for this manual. The revision level letter increases alphabetically as the manual undergoes subsequent updates. Addenda, which are released between revisions, contain important change information that the user should incorporate immediately into the manual. Addenda are numbered sequentially. When a new revision is created, all addenda associated with the previous revision of the manual are incorporated into the new revision of the manual. Each new revision includes a revised copy of this print history page.

Revision D (Document Number 155-022002)

......................................................................... February 2002

Revision E (Document Number 155-072002)

July 2002

Revision F (Document Number 155-082002)

August 2002

Revision G (Document Number 155-062004)

.................................................................................June 2004

Revision H (Document Number 155-082005)

............................................................................ August 2005

Revision J (Document Number 155-092007)

September 2007

Revision K (Document Number 155-062008)

June 2008

Revision L (Document Number 155-112008)

November 2008

Revision M (Document Number 155-122008)

...................................................................... December 2008

Revision N (Document Number 155-082010)

............................................................................ August 2010

Revision P (Document Number 155-102011)

October 2011

Visit www.teledyne-hi.com for WEEE disposal guidance.

CAUTION:

CAUTION:

CAUTION:

The instruments described in this manual are available with multiple pin-outs. Ensure that all electrical connections are correct.

The instruments described in this manual are designed for INDOOR use only.

The instruments described in this manual are designed for Class 2 installations in accordance with IPC standards

Hastings Instruments reserves the right to change or modify the design of its equipment without

any obligation to provide notification of change or intent to change.

HPM-2002-OBEVacuum Gauge

Page 2 of 39

Image 2
Contents Teledyne Hastings Manual Print History Table of Contents Troubleshooting HPM-2002-OBE Analog Output Module FeaturesModel 2002 Sensors HPM-2002-OBE Analog Output 4-20mA ModuleHPM-2002-OBE DeviceNet Module SpecificationsHPM-2002-OBE RS232/485 Output Module Receiving Inspection Transducer InstallationOBE Module Installation Quick StartInitial Operation Pin Volt 20 mA RS232/485High and Low Set Point Modes Analog OutputOverall Functional Description Run Mode Cal ModeAnalog Output GAS ModeGas Selection Table HPM-2002-OBEVacuum Gauge Analog Output 4-20mA Cal Mode Analog Output 4-20mA HPM-2002-OBEVacuum Gauge Command Syntax RS232/485 With DisplayInterrogation Commands Paramater Modification CommandsCalibration Adjustment Commands Reset / Restore CommandsDefault RS232/485 Specifications Device StatusModular Connector Pinout R2-232 RJ-11 connector on left side Modular Connector Pinout RS-485Run Mode DeviceNet TM DeviceNet descriptionAtmosphere Coefficient Adjustment Zero Coefficient AdjustmentMidrange Coefficient Adjustment Calibration of the HPM-2002-OBETheory of Operation Piezoresistive Sensor Vo = SPV+V1HPM-2002-OBEVacuum Gauge Es = K ∆T Am/L Pirani SensorEt = Es + Er + Eg Er = σεTh4-Ta4AsHPM-2002-OBEVacuum Gauge Dual Sensor Operation Eg = Kg ∆T As/∆xEg = arLt273/Th1/2Th-TaAgP HPM-2002-OBEVacuum Gauge Advanced Setup Guide RS485 AddressBaud Rate Turnaround DelayRestore Eeprom Data Bits/Parity Bits/Stop BitsSoftware Reset Restore CalibrationRestore Factory Defaults Frequently Asked Questions Why does my display read, Err1?Why does my display read, . U? Why does my display read, U.U?Why does my display read, U .? What are Err3, Err5, Err6 and Err7?Warranty Repair Policy Non-Warranty Repair PolicyDiagrams and Drawings HPM-2002-OBEVacuum Gauge HPM-2002-OBEVacuum Gauge