Vidikron Vision 90t, Vision 100t manual Using This Manual, If you need Turn to

Page 12

Introduction

Graphic Conventions: These symbols appear in numerous places throughout the manual, to emphasize points that you must keep in mind to avoid problems with your equipment or injury:

TIPS highlight time-saving short cuts and helpful guidelines for using

Tip

certain features.

 

NOTES emphasize text with unusual importance or special significance.

Note

They also provide supplemental information.

 

Caution

CAUTIONS alert users that a given action or omitted action can degrade

performance or cause a malfunction.

 

WARNINGS appear when a given action or omitted action can result in

WARNING damage to the equipment, or possible non-fatal injury to the user.

DANGER appears when a given action can cause severe injury or death.

DANGER!

1.2

Using This Manual

Use the following table to locate the specific information you need in this manual.

If you need...

... Turn to page:

 

 

Information about obtaining service

iv

 

 

General information about the Vision 90t/100t DLP

3

Projector

 

 

 

Installation instructions

13

 

 

First-time configuration instructions

27

 

 

Advanced configuration instructions

38

 

 

Troubleshooting tips

48

 

 

Vision 90t/100t DLP Projector specifications

55

 

 

2 Vidikron Vision Model 90t and Model 100t Owner’s Operating Manual

Image 12
Contents 90t/100t Page TWO Year Limited Warranty For Projectors, Video Processors and ControllersEffective Warranty Date Vidikron Safety Precautions 1Table of Contents Maintenance and Troubleshooting SpecificationsAppendix A. Vision 90t/100t Color Gamut Adjustment Operation1List of Figures Page 1Introduction About This ManualThis Manual Using This Manual If you need Turn toDescription, Features and Benefits Optional Accessories 2Controls and Functions Vision 90t/100t at a GlanceComponent Video RCA connectors Vision 90t/100t Rear PanelHD1 / HD2 Analog BNCs Volt 750 mA Trigger Outputs Video 1 / S-VIDEOPower Input 100 to 240 VAC Menu ButtonVision 90t/100t Remote Control On / OFFMemory Preset Buttons ISF NT Night Cursor KeysCust Video Comp ComponentHD 1 4 / HD 2 DVI 1 6 / DVI 2Page 3Installation Remote ControlQuick Setup Installation OverviewStep Procedure For Details Refer to Installation Considerations Projector Installation OptionsInstallation Type Advantages ConsiderationsVision 90t/100t Lens Options and Throw Ratios Throw RatioWith 126.9x54-inch ScreenPerfectly-centered image that completely fills the screen PositionShift ExamplesFolded Optics Installing the Optional CineWide LensMounting the Vision 90t/100tConnections to the Vision 90t/100t DVI Connections See FigureDigital DTV RGB Connections See Figure Digital DTV RGB ConnectionsAnalog Computer RGB Connections See Figure Analog RGB ConnectionsComposite/S-Video/Component Video Connections See Figure Composite, S-Video and Component Video ConnectionsConnection 10. RS-232 Control System Connection12. Connecting a 12-Volt Trigger Output to Other Equipment Power sourceTurning on the Power Adjusting the Picture Orientation4Operation Lens Adjustments Using the On-ScreenMenus FocusISF Presets ServiceInput Source Aspect RatioMain Menu Input SourceAspect Ratio Input Source Composite Video 1 S-Video Component SDAspect Ratio Settings DescriptionPicture RemotePicture Brightness Contrast Color Tint Sharpness Perform the adjustments in the order listed here Typical Pluge Pattern for Adjusting BrightnessGray Yellow Cyan Green Magenta Red Blue Gray Yellow Cyan Green Magenta Red Blue Input Position Input Position Left/Right Up/Down Width Height OverscanISF Presets ISF Presets ISF Night ISF Day Custom Save Factory DefaultInformation Information Serial Number Hardware Firmware Date May 31Calibration Should be used by ISF-certified technicians onlyGain/Offset Refer to ISF Night Display Color, above Service Input Names Restore Composite Video Component SDDo not change the Type setting in this menu ADC Bandwidth Auto YPbPr Input Resolution HD/RGB 1 and HD/RGB 2 Color Space Select Auto, RGB or YUVAuto Operation Page 5Maintenance and Troubleshooting Lamp ReplacementLens Replacement Only trained, authorized Vidikron dealers should attempt toMaintenance and Troubleshooting Troubleshooting Tips Troubleshooting ChartSymptom Possible Causes Solution Serial Command Syntax RS-232 Connection and Port ConfigurationSerial Commands 6Serial CommunicationsCommand Value Description Min/max Stored?Command Parameter Value Description Min/max Stored? PRESET?Iheight Bkgnd Page 7Specifications Vision 90t/100t SpecificationsVision 90t/100t Specifications Home Theater Calibration Specifications Industry-Standard SpecificationsLamp Estimated Lamp LifePower Requirements DimensionsWeight without lens Limited WarrantyVision 90t/100t Dimensions Vision 90t/100t DimensionsAVision 90t/100t Color Gamut Adjustment Figure A-1. CIE 1931 Chromaticity DiagramSerial Connections Equipment Setup Required Hardware SoftwareTable A-1. Serial Commands for Gamut Adjustment Command Parameter Value Description Min/maxAdjusting the Gamut For blue on the command lineVision 90t/100t Color Gamut Adjustment Page Page RUMA-011085