Vidikron Vision 90t, Vision 100t manual Menu Button, Power Input 100 to 240 VAC

Page 18

Controls and Functions

15.MENU BUTTON

Pressing the MENU button will bring up the main menu. Also, if you are in an adjustment mode or function, pressing MENU will bring the menu back one level.

16.IR SENSOR

Receives the IR commands from the remote.

17.POWER BUTTON

Press once to turn on the Vision 90t/100t. Press it again to put it into Standby mode. For a discrete on or off command, you can use the direct access buttons on the remote control.

18.POWER INPUT (100 to 240 VAC)

Connect the Vision 90t/100t to power here.

19.MAIN POWER SWITCH

Disconnects or applies power to the Vision 90t/100t.

20.POWER/STANDBY LED

8 Vidikron Vision Model 90t and Model 100t Owner’s Operating Manual

Image 18

Contents 90t/100t Page TWO Year Limited Warranty For Projectors, Video Processors and ControllersEffective Warranty Date Vidikron Safety Precautions 1Table of Contents Appendix A. Vision 90t/100t Color Gamut Adjustment Maintenance and TroubleshootingSpecifications Operation1List of Figures Page 1Introduction About This ManualThis Manual Using This Manual If you need Turn toDescription, Features and Benefits Optional Accessories 2Controls and Functions Vision 90t/100t at a GlanceComponent Video RCA connectors Vision 90t/100t Rear PanelHD1 / HD2 Analog BNCs Volt 750 mA Trigger Outputs Video 1 / S-VIDEOPower Input 100 to 240 VAC Menu ButtonVision 90t/100t Remote Control On / OFFMemory Preset Buttons ISF NT Night Cursor KeysCust HD 1 4 / HD 2 VideoComp Component DVI 1 6 / DVI 2Page 3Installation Remote ControlQuick Setup Installation OverviewStep Procedure For Details Refer to Installation Type Installation ConsiderationsProjector Installation Options Advantages ConsiderationsWith 126.9x54-inch Vision 90t/100t Lens Options and Throw RatiosThrow Ratio ScreenPerfectly-centered image that completely fills the screen PositionShift ExamplesFolded Optics Mounting the Vision Installing the OptionalCineWide Lens 90t/100tConnections to the Vision 90t/100t DVI Connections See FigureDigital DTV RGB Connections See Figure Digital DTV RGB ConnectionsAnalog Computer RGB Connections See Figure Analog RGB ConnectionsComposite/S-Video/Component Video Connections See Figure Composite, S-Video and Component Video ConnectionsConnection 10. RS-232 Control System Connection12. Connecting a 12-Volt Trigger Output to Other Equipment Power sourceTurning on the Power Adjusting the Picture Orientation4Operation Menus Lens AdjustmentsUsing the On-Screen FocusInput Source ISF PresetsService Aspect RatioAspect Ratio Main MenuInput Source Input Source Composite Video 1 S-Video Component SDAspect Ratio Settings DescriptionPicture RemotePicture Brightness Contrast Color Tint Sharpness Perform the adjustments in the order listed here Typical Pluge Pattern for Adjusting BrightnessGray Yellow Cyan Green Magenta Red Blue Gray Yellow Cyan Green Magenta Red Blue Input Position Input Position Left/Right Up/Down Width Height OverscanInformation ISF PresetsISF Presets ISF Night ISF Day Custom Save Factory Default Information Serial Number Hardware Firmware Date May 31Calibration Should be used by ISF-certified technicians onlyGain/Offset Refer to ISF Night Display Color, above Service Input Names Restore Composite Video Component SDDo not change the Type setting in this menu ADC Bandwidth Auto YPbPr Input Resolution HD/RGB 1 and HD/RGB 2 Color Space Select Auto, RGB or YUVAuto Operation Page 5Maintenance and Troubleshooting Lamp ReplacementLens Replacement Only trained, authorized Vidikron dealers should attempt toMaintenance and Troubleshooting Troubleshooting Tips Troubleshooting ChartSymptom Possible Causes Solution Serial Commands Serial Command SyntaxRS-232 Connection and Port Configuration 6Serial CommunicationsCommand Value Description Min/max Stored?Command Parameter Value Description Min/max Stored? PRESET?Iheight Bkgnd Page 7Specifications Vision 90t/100t SpecificationsVision 90t/100t Specifications Lamp Home Theater Calibration SpecificationsIndustry-Standard Specifications Estimated Lamp LifeWeight without lens Power RequirementsDimensions Limited WarrantyVision 90t/100t Dimensions Vision 90t/100t DimensionsAVision 90t/100t Color Gamut Adjustment Figure A-1. CIE 1931 Chromaticity DiagramSerial Connections Equipment Setup Required Hardware SoftwareTable A-1. Serial Commands for Gamut Adjustment Command Parameter Value Description Min/maxAdjusting the Gamut For blue on the command lineVision 90t/100t Color Gamut Adjustment Page Page RUMA-011085