Vidikron Vision 100t, Vision 90t manual Table A-1. Serial Commands for Gamut Adjustment

Page 71

Vision 90t/100t Color Gamut Adjustment

Figure A-3. Vision 90t/100t Secondary RS-232 Port

4.Connect the color sensor to any available COM or USB port.

5.Launch HyperTerminal. Open a connection using these parameters: 19200 baud, 8 data bits, no parity,1 stop bit and no flow control.

6.Press <Enter>. The Vision 90t/100t responds with “+>” to indicate that it is ready to accept commands.

7.Start your color analyzer. Position the sensor approximately 6 to 12 inches from the screen, facing it at a slight angle (upward or to one side) so that the color of the screen is included in the calibration.

Table A-1lists the serial command set for color gamut adjustments. The “Parameter (min/max)” column shows the valid parameter ranges, or “NA” for commands that take no parameters.

When you enter a valid command, the Vision 90t/100t executes it and acknowledges it with a plus sign on the command line (+ >). When you enter an invalid command – one that is misspelled or followed by values outside the valid range for that command – the Vision 90t/100t ignores it and returns a minus sign (- >).

Table A-1. Serial Commands for Gamut Adjustment

Command

Parameter

Value

Description

(min/max)

Stored?

 

 

 

 

 

 

GAMUT WHITE

NA

NA

Displays white field on screen for

 

 

 

measuring x and y coordinates;

 

 

 

shows current x and y coordinates

 

 

 

for white on the command line.

 

 

 

 

GAMUT RED

NA

NA

Displays red field on screen for

 

 

 

measuring x and y coordinates;

 

 

 

shows current x and y coordinates

 

 

 

for red on the command line.

 

 

 

 

A.3

Serial Command Syntax

Vidikron Vision Model 90t and Model 100t Owner’s Operating Manual

A-3

Image 71
Contents 90t/100t Page For Projectors, Video Processors and Controllers TWO Year Limited WarrantyEffective Warranty Date Vidikron Safety Precautions 1Table of Contents Operation Maintenance and TroubleshootingSpecifications Appendix A. Vision 90t/100t Color Gamut Adjustment1List of Figures Page This Manual 1IntroductionAbout This Manual If you need Turn to Using This ManualDescription, Features and Benefits Optional Accessories Vision 90t/100t at a Glance 2Controls and FunctionsHD1 / HD2 Analog BNCs Component Video RCA connectorsVision 90t/100t Rear Panel Video 1 / S-VIDEO Volt 750 mA Trigger OutputsMenu Button Power Input 100 to 240 VACOn / OFF Vision 90t/100t Remote ControlCust Memory Preset Buttons ISF NT NightCursor Keys DVI 1 6 / DVI 2 VideoComp Component HD 1 4 / HD 2Page Remote Control 3InstallationStep Procedure For Details Refer to Quick SetupInstallation Overview Advantages Considerations Installation ConsiderationsProjector Installation Options Installation TypeScreen Vision 90t/100t Lens Options and Throw RatiosThrow Ratio With 126.9x54-inchPosition Perfectly-centered image that completely fills the screenExamples ShiftFolded Optics 90t/100t Installing the OptionalCineWide Lens Mounting the VisionDVI Connections See Figure Connections to the Vision 90t/100tDigital DTV RGB Connections Digital DTV RGB Connections See FigureAnalog RGB Connections Analog Computer RGB Connections See FigureComposite, S-Video and Component Video Connections Composite/S-Video/Component Video Connections See Figure10. RS-232 Control System Connection ConnectionPower source 12. Connecting a 12-Volt Trigger Output to Other Equipment4Operation Turning on the PowerAdjusting the Picture Orientation Focus Lens AdjustmentsUsing the On-Screen MenusAspect Ratio ISF PresetsService Input SourceInput Source Composite Video 1 S-Video Component SD Main MenuInput Source Aspect RatioDescription Aspect Ratio SettingsPicture Brightness Contrast Color Tint Sharpness PictureRemote Typical Pluge Pattern for Adjusting Brightness Perform the adjustments in the order listed hereGray Yellow Cyan Green Magenta Red Blue Gray Yellow Cyan Green Magenta Red Blue Input Position Left/Right Up/Down Width Height Overscan Input PositionInformation Serial Number Hardware Firmware Date May 31 ISF PresetsISF Presets ISF Night ISF Day Custom Save Factory Default InformationShould be used by ISF-certified technicians only CalibrationGain/Offset Refer to ISF Night Display Color, above Input Names Restore Composite Video Component SD ServiceDo not change the Type setting in this menu Auto ADC Bandwidth Auto YPbPr Input ResolutionHD/RGB 1 and HD/RGB 2 Color Space Select Auto, RGB or YUV Operation Page Lamp Replacement 5Maintenance and TroubleshootingOnly trained, authorized Vidikron dealers should attempt to Lens ReplacementMaintenance and Troubleshooting Symptom Possible Causes Solution Troubleshooting TipsTroubleshooting Chart 6Serial Communications Serial Command SyntaxRS-232 Connection and Port Configuration Serial CommandsValue Description Min/max Stored? CommandPRESET? Command Parameter Value Description Min/max Stored?Iheight Bkgnd Page Vision 90t/100t Specifications 7SpecificationsVision 90t/100t Specifications Estimated Lamp Life Home Theater Calibration SpecificationsIndustry-Standard Specifications LampLimited Warranty Power RequirementsDimensions Weight without lensVision 90t/100t Dimensions Vision 90t/100t DimensionsFigure A-1. CIE 1931 Chromaticity Diagram AVision 90t/100t Color Gamut AdjustmentRequired Hardware Software Serial Connections Equipment SetupCommand Parameter Value Description Min/max Table A-1. Serial Commands for Gamut AdjustmentFor blue on the command line Adjusting the GamutVision 90t/100t Color Gamut Adjustment Page Page RUMA-011085