Vidikron Vision 50 manual With AutoScope

Page 32

Installation

Installing the AutoScope Lens ➤ Figure 3-5shows the Vision 50/CineWide with AutoScope motor assembly.

Motor (Vision 50/CineWide
with AutoScope)	CineWide with
3	CineWide with
	AutoScope
Screw, Phillips 2	Ceiling Mount
Pan-Head,	Adapter/
10-32 x 1/2”	Projector Stand,
(10x)	Right

AutoScope 1

Lens Motor

4CineWide with AutoScope Ceiling Mount Adapter/ Projector Stand, Left

5 Nylon Spacer, 5/8” diameter x 3/16” high (10x)

Figure 3-5. Vision 50/CineWide with AutoScope Motor Assembly – Exploded View

Remove Projector Front Height Adjusters:

Place the projector upside down on a blanket or other soft surface. Then, remove the two height adjusters at the front of the projector by turning them counterclockwise until they come out.

20	Vidikron Vision 50 Series Owner’s Operating Manual

Image 32

Contents Series DLP Projectors Page TWO Year Limited Warranty For Projectors, Video Processors and ControllersEffective Warranty Date Vidikron Safety Precautions 1Table of Contents Maintenance and Troubleshooting OperationSerial Communications Table of Contents 1List of Figures List of Figures Xii 1Introduction About This ManualUsing This Manual They also provide supplemental informationPerformance or cause a malfunction If you need Turn toDescription, Features and Benefits Optional Accessories POWER/STANDBY LED Indicates power status as follows Vision 50 at a GlanceTemp LED Cable Access Door Open to access connectors Vision 50 Connector PanelRefer to Vision 50 Connector Panel, below Comp 1 RCA connectors Built-In KeypadHdmi Digital Volt 250 mA Trigger Output 3.5-mm, mini phono jackVision 50 Remote Control Vision 50 Remote ControlOn / OFF Source Selection Buttons Comp 1 SD ComponentVID S-Video Comp 2 HD ComponentMemory Preset Buttons Cursor KeysPicture-In-Picture PIP / Picture-By-Picture PBP Controls VAC V2 Aperture ControlRemote Control/Built-In Keypad Functional Comparison Motorized Lens ControlsOperation 3InstallationRemote Control Quick Setup Installation OverviewStep Procedure For Details, Refer to If installing a Vision 50/CineWide or Vision 50/CineWideInstallation Considerations Projector Installation OptionsInstallation Type Advantages ConsiderationsThrow Ratios for the Vision 50 Series Throw Range Throw RatioProjector Model VisionCeiling Installation Floor InstallationVertical and Horizontal PositionFolded Optics Installing the Optional CineWide Lens Mount With AutoScope Vision 50 with Ceiling Mount Adapters/Projector Stands AutoScope Lens Motor Installation Installing the Fixed CineWide Base Plate Vision 50/CineWide Vision 50/CineWide with Lens Base PlateAdjusting the Projector Mounting the VisionFloor Mounting Upright Ceiling Mounting InvertedConnector Panel Access Connecting SourceConnections to the Vision Hdmi or DVI Source10. RGB Connections DVD Player or HD Set Top Box Personal Computer11. Progressive Component Video Connections DTV or Progressive Component YPbPr Source12. Composite, S-Video and Component Video Connections DTV Source DVD Player, VCR Satellite Receiver Etc13. RS-232 Control System Connection 15. Connecting the 12-volt Trigger Output to Other Equipment EquipmentPower source Turning on the PowerConnecting to AC Power Focus Zoom Vertical Lens Shift Primary lens is perfectly centered on the screen Installing and Adjusting the CineWide Anamorphic LensAnamorphic Lens Installation Adjustment Vision 50/CineWide Adjusting the Lens Height Y Anamorphic Lens Top View AutoScope AdjustmentVision 50/CineWide with Attach Lens Mounting Assembly to Lens Motor Carriage Plate 18. Attaching the Anamorphic Lens to the Lens Adapter RingAdjusting the Horizontal X Lens Position Installation Anamorphic Lens Top View Adjusting the Geometry Installation Using Picture-In-Picture/ Picture-By-Picture PIP/PBP 4OperationSelecting Video Memory Selecting an Aspect Ratio Selecting An Input SourceUsing the On-Screen Menus Adjust InstallationService PicturePicture Adjust Main MenuPerform the adjustments in the order listed here Typical Pluge Pattern for Adjusting BrightnessGray Yellow Cyan Green Magenta Red Blue Gray Yellow Cyan Green Magenta Red Blue Typical Test Pattern for Adjusting Sharpness Image Option Image OptionAspect Ratio Settings DescriptionRemote Projector Status Installation Exit to return to the previous menu or Menu to exitService ServiceOperation Operation Remote Control ISF Calibration ISF CalibrationOperation Operation Lamp assembly for replacement 5Maintenance and TroubleshootingLamp Replacement Symptom Possible Causes Solution Troubleshooting TipsTroubleshooting Chart Temp and Lamp LEDs are both Maintenance and Troubleshooting Serial Command Syntax RS-232 Connection and Port ConfigurationSerial Commands 6Serial CommunicationsSerial Communications Serial Commands Serial Commands 7Specifications Vision 50 SpecificationsHome Theater Calibration Specifications Industry-Standard SpecificationsPower Requirements DimensionsRegulatory Approvals Limited WarrantySpecifications are subject to change without notice Vision 50 Dimensions Vision 50 Dimensions with Optional Fixed Anamorphic LensVidikron Vision 50 Series Owner’s Operating Manual Power-cycle the projector to see the change Page Vidikron