Vidikron Vision 50 manual Adjusting the Lens Height Y

Page 46

Installation

1.Use the Pitch/Y-Adjustment Screws and Washers (item #6) to attach the Vertical Mounting Brackets (item #5) to the Anamorphic Lens (item #1).

2.Place the lens with the brackets installed on top of (or under, if the projector is inverted) the Base Plate (item #2), so that the two threaded posts at the bottom of the brackets pass through the corresponding slots on the base plate.

3.Secure the lens assembly to the base plate with the Yaw/Z-Adjustment Levers and Fiber Washers (item #4).

To avoid clipping the corners of the image, position the anamorphic lens

Tip

as close as possible to the primary lens.

 

 

 

Ceiling Mount

 

 

Bracket

 

 

 

 

Adjusting the Lens Height (Y):

1.Project a white field on the screen.

2.Ensure that the two Pitch/Y-Adjustment Screws are loose enough to allow vertical movement of the lens assembly.

3.Slowly move the anamorphic lens into place so that there are no shadows on the top or bottom of the screen:

Too Low

Correct position

Too High

4.When the height is properly set, tighten the Pitch/Y-Adjustment Screws to secure the lens in place.

Adjusting the Pitch (Angle): Next, angle the lens to even out any top-to-bottom pincushion distortion. To do this, loosen the Pitch/Y-Adjustment Screws on either side of the lens to allow it to pivot freely. Then, adjust the anamorphic lens angle so that the projected image is rectangular:

34

Vidikron Vision 50 Series Owner’s Operating Manual

Image 46
Contents Series DLP Projectors Page TWO Year Limited Warranty For Projectors, Video Processors and ControllersEffective Warranty Date Vidikron Safety Precautions 1Table of Contents Maintenance and Troubleshooting OperationSerial Communications Table of Contents 1List of Figures List of Figures Xii 1Introduction About This ManualPerformance or cause a malfunction Using This ManualThey also provide supplemental information If you need Turn toDescription, Features and Benefits Optional Accessories POWER/STANDBY LED Indicates power status as follows Vision 50 at a GlanceTemp LED Refer to Vision 50 Connector Panel, below Vision 50 Connector PanelCable Access Door Open to access connectors Hdmi Digital Comp 1 RCA connectorsBuilt-In Keypad Volt 250 mA Trigger Output 3.5-mm, mini phono jackVision 50 Remote Control Vision 50 Remote ControlVID S-Video On / OFFSource Selection Buttons Comp 1 SD Component Comp 2 HD ComponentPicture-In-Picture PIP / Picture-By-Picture PBP Controls Memory Preset ButtonsCursor Keys VAC V2 Aperture ControlRemote Control/Built-In Keypad Functional Comparison Motorized Lens ControlsRemote Control 3InstallationOperation Step Procedure For Details, Refer to Quick SetupInstallation Overview If installing a Vision 50/CineWide or Vision 50/CineWideInstallation Type Installation ConsiderationsProjector Installation Options Advantages ConsiderationsProjector Model Throw Ratios for the Vision 50 SeriesThrow Range Throw Ratio VisionVertical and Horizontal Ceiling InstallationFloor Installation PositionFolded Optics Installing the Optional CineWide Lens Mount With AutoScope Vision 50 with Ceiling Mount Adapters/Projector Stands AutoScope Lens Motor Installation Installing the Fixed CineWide Base Plate Vision 50/CineWide Vision 50/CineWide with Lens Base PlateFloor Mounting Upright Adjusting the ProjectorMounting the Vision Ceiling Mounting InvertedConnections to the Vision Connector Panel AccessConnecting Source Hdmi or DVI Source10. RGB Connections DVD Player or HD Set Top Box Personal Computer11. Progressive Component Video Connections DTV or Progressive Component YPbPr Source12. Composite, S-Video and Component Video Connections DTV Source DVD Player, VCR Satellite Receiver Etc13. RS-232 Control System Connection 15. Connecting the 12-volt Trigger Output to Other Equipment EquipmentConnecting to AC Power Turning on the PowerPower source Focus Zoom Vertical Lens Shift Anamorphic Lens Installation Adjustment Vision 50/CineWide Installing and Adjusting the CineWide Anamorphic LensPrimary lens is perfectly centered on the screen Adjusting the Lens Height Y Anamorphic Lens Top View Vision 50/CineWide with AdjustmentAutoScope Attach Lens Mounting Assembly to Lens Motor Carriage Plate 18. Attaching the Anamorphic Lens to the Lens Adapter RingAdjusting the Horizontal X Lens Position Installation Anamorphic Lens Top View Adjusting the Geometry Installation Selecting Video Memory Using Picture-In-Picture/ Picture-By-Picture PIP/PBP4Operation Selecting an Aspect Ratio Selecting An Input SourceUsing the On-Screen Menus Service AdjustInstallation PicturePicture Adjust Main MenuPerform the adjustments in the order listed here Typical Pluge Pattern for Adjusting BrightnessGray Yellow Cyan Green Magenta Red Blue Gray Yellow Cyan Green Magenta Red Blue Typical Test Pattern for Adjusting Sharpness Image Option Image OptionAspect Ratio Settings DescriptionRemote Projector Status Installation Exit to return to the previous menu or Menu to exitService ServiceOperation Operation Remote Control ISF Calibration ISF CalibrationOperation Operation Lamp Replacement 5Maintenance and TroubleshootingLamp assembly for replacement Troubleshooting Chart Troubleshooting TipsSymptom Possible Causes Solution Temp and Lamp LEDs are both Maintenance and Troubleshooting Serial Commands Serial Command SyntaxRS-232 Connection and Port Configuration 6Serial CommunicationsSerial Communications Serial Commands Serial Commands 7Specifications Vision 50 SpecificationsPower Requirements Home Theater Calibration SpecificationsIndustry-Standard Specifications DimensionsSpecifications are subject to change without notice Limited WarrantyRegulatory Approvals Vision 50 Dimensions Vision 50 Dimensions with Optional Fixed Anamorphic LensVidikron Vision 50 Series Owner’s Operating Manual Power-cycle the projector to see the change Page Vidikron