Vidikron Vision 50 manual Using This Manual, They also provide supplemental information

Page 14

Introduction

Graphic Conventions: These symbols appear in numerous places throughout the manual, to emphasize points that you must keep in mind to avoid problems with your equipment or injury:

TIPS highlight time-saving short cuts and helpful guidelines for using

Tip

certain features.

 

NOTES emphasize text with unusual importance or special significance.

Note

They also provide supplemental information.

 

Caution

CAUTIONS alert users that a given action or omitted action can degrade

performance or cause a malfunction.

 

WARNINGS appear when a given action or omitted action can result in

WARNING damage to the equipment, or possible non-fatal injury to the user.

DANGER appears when a given action can cause severe injury or death.

DANGER!

1.2

Using This Manual

Use the following table to locate the specific information you need in this manual.

If you need...

... Turn to page:

 

 

Information about obtaining service

iv

 

 

General information about the Vision 50 Series DLP Projectors

3

 

 

Installation instructions

13

 

 

First-time configuration instructions

32

 

 

Advanced configuration instructions

56

 

 

Troubleshooting tips

64

 

 

Specifications for the Vision 50 Series DLP Projectors

71

 

 

2

Vidikron Vision 50 Series Owner’s Operating Manual

Image 14
Contents Series DLP Projectors Page TWO Year Limited Warranty For Projectors, Video Processors and ControllersEffective Warranty Date Vidikron Safety Precautions 1Table of Contents Maintenance and Troubleshooting OperationSerial Communications Table of Contents 1List of Figures List of Figures Xii 1Introduction About This ManualPerformance or cause a malfunction Using This ManualThey also provide supplemental information If you need Turn toDescription, Features and Benefits Optional Accessories POWER/STANDBY LED Indicates power status as follows Vision 50 at a GlanceTemp LED Cable Access Door Open to access connectors Vision 50 Connector PanelRefer to Vision 50 Connector Panel, below Hdmi Digital Comp 1 RCA connectorsBuilt-In Keypad Volt 250 mA Trigger Output 3.5-mm, mini phono jackVision 50 Remote Control Vision 50 Remote ControlVID S-Video On / OFFSource Selection Buttons Comp 1 SD Component Comp 2 HD ComponentPicture-In-Picture PIP / Picture-By-Picture PBP Controls Memory Preset ButtonsCursor Keys VAC V2 Aperture ControlRemote Control/Built-In Keypad Functional Comparison Motorized Lens ControlsOperation 3InstallationRemote Control Step Procedure For Details, Refer to Quick SetupInstallation Overview If installing a Vision 50/CineWide or Vision 50/CineWideInstallation Type Installation ConsiderationsProjector Installation Options Advantages ConsiderationsProjector Model Throw Ratios for the Vision 50 SeriesThrow Range Throw Ratio VisionVertical and Horizontal Ceiling InstallationFloor Installation PositionFolded Optics Installing the Optional CineWide Lens Mount With AutoScope Vision 50 with Ceiling Mount Adapters/Projector Stands AutoScope Lens Motor Installation Installing the Fixed CineWide Base Plate Vision 50/CineWide Vision 50/CineWide with Lens Base PlateFloor Mounting Upright Adjusting the ProjectorMounting the Vision Ceiling Mounting InvertedConnections to the Vision Connector Panel AccessConnecting Source Hdmi or DVI Source10. RGB Connections DVD Player or HD Set Top Box Personal Computer11. Progressive Component Video Connections DTV or Progressive Component YPbPr Source12. Composite, S-Video and Component Video Connections DTV Source DVD Player, VCR Satellite Receiver Etc13. RS-232 Control System Connection 15. Connecting the 12-volt Trigger Output to Other Equipment EquipmentPower source Turning on the PowerConnecting to AC Power Focus Zoom Vertical Lens Shift Primary lens is perfectly centered on the screen Installing and Adjusting the CineWide Anamorphic LensAnamorphic Lens Installation Adjustment Vision 50/CineWide Adjusting the Lens Height Y Anamorphic Lens Top View AutoScope AdjustmentVision 50/CineWide with Attach Lens Mounting Assembly to Lens Motor Carriage Plate 18. Attaching the Anamorphic Lens to the Lens Adapter RingAdjusting the Horizontal X Lens Position Installation Anamorphic Lens Top View Adjusting the Geometry Installation Selecting Video Memory Using Picture-In-Picture/ Picture-By-Picture PIP/PBP4Operation Selecting an Aspect Ratio Selecting An Input SourceUsing the On-Screen Menus Service AdjustInstallation PicturePicture Adjust Main MenuPerform the adjustments in the order listed here Typical Pluge Pattern for Adjusting BrightnessGray Yellow Cyan Green Magenta Red Blue Gray Yellow Cyan Green Magenta Red Blue Typical Test Pattern for Adjusting Sharpness Image Option Image OptionAspect Ratio Settings DescriptionRemote Projector Status Installation Exit to return to the previous menu or Menu to exitService ServiceOperation Operation Remote Control ISF Calibration ISF CalibrationOperation Operation Lamp assembly for replacement 5Maintenance and TroubleshootingLamp Replacement Symptom Possible Causes Solution Troubleshooting TipsTroubleshooting Chart Temp and Lamp LEDs are both Maintenance and Troubleshooting Serial Commands Serial Command SyntaxRS-232 Connection and Port Configuration 6Serial CommunicationsSerial Communications Serial Commands Serial Commands 7Specifications Vision 50 SpecificationsPower Requirements Home Theater Calibration SpecificationsIndustry-Standard Specifications DimensionsRegulatory Approvals Limited WarrantySpecifications are subject to change without notice Vision 50 Dimensions Vision 50 Dimensions with Optional Fixed Anamorphic LensVidikron Vision 50 Series Owner’s Operating Manual Power-cycle the projector to see the change Page Vidikron