Vidikron Vision 50 manual Picture, Adjust, Image, Option, Projector, Status, Installation, Service

Operation

	Brightness	0 ... 60
	Contrast	0 ... 32
	Color	0 ... 64
Picture
	Tint	0 ... 30
Adjust	Sharpness	-14 ... 0 ... +25
	Color Temp.	0, 1 (5400 K), 2 (6500K), 3
		(8500 K), 4 or 5 (Custom)
	Color Select	Standard, NTSC, HDTV or
		PAL
		Video, S-Video,
	Input Select	Component 1,
		Component 2, RGB-HD or
		HDMI
		Anamorphic (16:9)
		Standard (4:3)
		Letterbox
	Aspect Ratio	IntelliWide
		Cinema
		Cinema Fill
		(Vision 50/CineWide and
		Vision 50/CineWide with
		AutoScope only)
		H Enhance
Image		V Enhance	0, 1, 2, 3 ... 127
	SD Enhance	C (Chroma) Enhance
Option
		H Threshold
		V Threshold	10, 11, 12, 13 ... 127
		C (Chroma) Threshold
	Video Filter	0, 1, 2 or 3
		Auto Adj.
		Frequency	0, +1, +2, +3 ... +17
	HD/RGB Adjust	Phase	0, +1, +2, +3 ... +31
	(480p and higher-res.
		H. Position	-30, -29 ... 0 ... +29,
	signals only)
			+30
		V. Position	-28, -27 ... 0 ... +29,
			+30
	Blue Enable	On / Off
	Save Settings	Custom 1
	Load Saved Settings	Custom 1, ISF Night or
		ISF Day
Projector	Default
	Sleep Timer	0, 10, 20, 30 ... 180 minutes
Status
	Lamp Power	250W or 200W
	Lamp Hours	(read-only)
	Language	English, Français, Español,
		Deutsch or Italiano
	Picture Configuration	Floor Front, Floor Rear,
		Ceiling Front or Ceiling Rear
	Keystone	-14, -13 ... 0 ... +13, +14
	OSD Position	Horizontal/Vertical	0/0 (lower left) ...
			20/20 (upper right)
Installation	OSD Timer	0, 3, 6, 9 ... 60 seconds
		PIP/PBP Enable	On / Off
			PIP Off
		PIP Set Up	Graphic in Video
	PIP/PBP Setup		Video in Graphic
			PBP Off
		PBP Set Up	Graphic by Video
			Video by Graphic
	Background Color	Grey, Blue or White

		Gain
		Offset	Red / Green / Blue
	White Balance	Gamma
		Save Color Temp. 4
		Save Color Temp. 5
	Gamma Selection	2.8, 2.5, 2.2, 1.0, 2.1, 2.15 or
		2.7
	ICC Adjust	NTSC / HDTV / PAL	R / G / B / Y / C / M
			Intensity / Sat. / Hue
		Total	0, +1, +2, +3 ... +15
	Image Over Scan	Horizontal
		Vertical
	Video Black Level	0 IRE or 7.5 IRE
	Aperture Control	0, 1, 2 ... 19
	Image Shift	Horizontal	-30, -29, ... 0 ... +29,
		Vertical	+30
Service	Amplitude	Horizontal	-60, -59 ... 0 ... +59,
		Vertical	+60
			(Vision 50/CineWide
	Horizontal Masking	0, +1, +2, +3 ... +100	and Vision
			50/CineWide with
			AutoScope only)
			Auto Normal,
	Fan Control	Mode	Auto Hi. Altitude or
			Manual
		Fan Speed (Manual Mode)
	Lamp Reset Timer	Yes / No
	RS-232 Baud Rate	9600, 38400 or 115200
	Remote Control	Primary
		Secondary
			(Vision 50/CineWide
	Screen Trigger Mode	Normal or Trigger	and Vision
			50/CineWide with
			AutoScope only)
	Return to User OSD
	Picture Adjust	Brightness, Contrast, Color	(see above)
		etc.
	White Balance	Gamma, Gain, Offset etc.	(see above)
	Gamma Selection	2.8, 2.5, 2.2, 1.0, 2.1, 2.15
ISF		or 2.7
	Aperture Control	0, 1, 2 ... 19
Calibration
	Blue Enable	On / Off
	Save ISF Settings	ISF Night or ISF Day
	Splash Screen Timer	5, 6, 7 ... 60 seconds
	ISF Enable	On / Off
	Return to User OSD

Figure 4-1. Vision 50 OSD Menu Structure

Vidikron Vision 50 Series Owner’s Operating Manual 45