Vidikron manual Vidikron Vision 50 Series Owner’s Operating Manual

Page 87

Appendix A. Personalizing the ISF Splash Screen on the Vision 50

This Appendix describes how to personalize the ISF splash screen on the Vidikron Vision 50

Series DLP Projectors.

Only ISF-trained and -certified technicians should attempt this

Note procedure!

1.Connect a PC to the Vision 50 RS-232 port and establish a serial connection; refer to RS-232 Connection and Port Configuration on page 67 if you need instructions.

2.Press MENU on the projector remote control. Use the up- or down-arrow keys to highlight ISF Calibration and press ENTER. Use the number buttons on the remote control to enter the ISF Calibration menu passcode, then press ENTER again.

3.Press MENU on the projector remote control. Then, select Splash Screen Timer from the ISF Calibration menu.

4.Use the left- or right-arrow buttons to set the Splash Screen Timer. This timer controls how long the startup (Vidikron/ISF logo) image stays on-screen after you turn on the projector. The range is from 5 to 60 seconds in 1-second increments. For this procedure, set it to 30 seconds and press EXIT.

5.In the HyperTerminal window, at the command prompt (>), type U1 followed by the customer name, four or five spaces and the ISF calibrator name:

6.Press <Enter>.

7.Press MENU on the projector remote control. Then, select ISF Calibration from the Main menu.

8.Select ISF Enable from the ISF Calibration menu and set it to On.

Vidikron Vision 50 Series Owner’s Operating Manual

A-1

Image 87
Contents Series DLP Projectors Page For Projectors, Video Processors and Controllers TWO Year Limited WarrantyEffective Warranty Date Vidikron Safety Precautions 1Table of Contents Operation Maintenance and TroubleshootingSerial Communications Table of Contents 1List of Figures List of Figures Xii About This Manual 1IntroductionIf you need Turn to Using This ManualThey also provide supplemental information Performance or cause a malfunctionDescription, Features and Benefits Optional Accessories Vision 50 at a Glance POWER/STANDBY LED Indicates power status as followsTemp LED Vision 50 Connector Panel Refer to Vision 50 Connector Panel, belowCable Access Door Open to access connectors Volt 250 mA Trigger Output 3.5-mm, mini phono jack Comp 1 RCA connectorsBuilt-In Keypad Hdmi DigitalVision 50 Remote Control Vision 50 Remote ControlComp 2 HD Component On / OFFSource Selection Buttons Comp 1 SD Component VID S-VideoVAC V2 Aperture Control Memory Preset ButtonsCursor Keys Picture-In-Picture PIP / Picture-By-Picture PBP ControlsMotorized Lens Controls Remote Control/Built-In Keypad Functional Comparison3Installation Remote ControlOperation If installing a Vision 50/CineWide or Vision 50/CineWide Quick SetupInstallation Overview Step Procedure For Details, Refer toAdvantages Considerations Installation ConsiderationsProjector Installation Options Installation TypeVision Throw Ratios for the Vision 50 SeriesThrow Range Throw Ratio Projector ModelPosition Ceiling InstallationFloor Installation Vertical and HorizontalFolded Optics Installing the Optional CineWide Lens Mount With AutoScope Vision 50 with Ceiling Mount Adapters/Projector Stands AutoScope Lens Motor Installation Vision 50/CineWide with Lens Base Plate Installing the Fixed CineWide Base Plate Vision 50/CineWideCeiling Mounting Inverted Adjusting the ProjectorMounting the Vision Floor Mounting UprightHdmi or DVI Source Connector Panel AccessConnecting Source Connections to the VisionDVD Player or HD Set Top Box Personal Computer 10. RGB ConnectionsDTV or Progressive Component YPbPr Source 11. Progressive Component Video ConnectionsDTV Source DVD Player, VCR Satellite Receiver Etc 12. Composite, S-Video and Component Video Connections13. RS-232 Control System Connection Equipment 15. Connecting the 12-volt Trigger Output to Other EquipmentTurning on the Power Connecting to AC PowerPower source Focus Zoom Vertical Lens Shift Installing and Adjusting the CineWide Anamorphic Lens Anamorphic Lens Installation Adjustment Vision 50/CineWidePrimary lens is perfectly centered on the screen Adjusting the Lens Height Y Anamorphic Lens Top View Adjustment Vision 50/CineWide withAutoScope 18. Attaching the Anamorphic Lens to the Lens Adapter Ring Attach Lens Mounting Assembly to Lens Motor Carriage PlateAdjusting the Horizontal X Lens Position Installation Anamorphic Lens Top View Adjusting the Geometry Installation Selecting an Aspect Ratio Selecting An Input Source Using Picture-In-Picture/ Picture-By-Picture PIP/PBP4Operation Selecting Video MemoryUsing the On-Screen Menus Picture AdjustInstallation ServiceMain Menu Picture AdjustTypical Pluge Pattern for Adjusting Brightness Perform the adjustments in the order listed hereGray Yellow Cyan Green Magenta Red Blue Gray Yellow Cyan Green Magenta Red Blue Typical Test Pattern for Adjusting Sharpness Image Option Image OptionDescription Aspect Ratio SettingsRemote Projector Status Exit to return to the previous menu or Menu to exit InstallationService ServiceOperation Operation Remote Control ISF Calibration ISF CalibrationOperation Operation 5Maintenance and Troubleshooting Lamp ReplacementLamp assembly for replacement Troubleshooting Tips Troubleshooting ChartSymptom Possible Causes Solution Temp and Lamp LEDs are both Maintenance and Troubleshooting 6Serial Communications Serial Command SyntaxRS-232 Connection and Port Configuration Serial CommandsSerial Communications Serial Commands Serial Commands Vision 50 Specifications 7SpecificationsDimensions Home Theater Calibration SpecificationsIndustry-Standard Specifications Power RequirementsLimited Warranty Specifications are subject to change without noticeRegulatory Approvals Vision 50 Dimensions with Optional Fixed Anamorphic Lens Vision 50 DimensionsVidikron Vision 50 Series Owner’s Operating Manual Power-cycle the projector to see the change Page Vidikron