B&B Electronics MES1B manual Connecting to the MES1A/B, Press Enter to go into Setup Mode

Page 26

Getting Started

Connecting to the MES1A/B

Before configuration can occur you must set up a telnet connection with the MES1A/B to access the Configuration Menu. You can access the Configuration Menu using a standard telnet window, or use the telnet implementation within the Device Installer software. The Device Installer option provides an all-in-one user interface for working with the MES1A/B

To connect:

3.Select the Telnet Configuration tab. The tab shows the IP Address of the MES1A/B and the Port Number used to communicate with it via telnet. The rest of the window is blank.

4.Click Connect to connect to the MES1A/B. When a connection is established the following window appears, which contains information on the MAC address and Software version of the MES1A/B.

Figure 12. Press Enter to go into Setup Mode

The background color of the window remains white for five seconds, then changes to gray when it times out.

5.Press the Enter key within five seconds to go into Setup Mode or it will time out (and you will have to click Clear and repeat the process).

The MES1A/B Configuration Menu appears.

Manual Documentation Number: MES1A/MES1B-2106m

PN7138-rev001

B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104 – www.bb-elec.comB&B Electronics Ltd – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445 – www.bb-europe.com

16

Image 26

Contents Modbus TCP Modbus Ascii / RTU Converters Models MES1A, MES1BManual Documentation Number MES1A/MES1B-2106m International Headquarters Page Manual Documentation Number MES1A/MES1B-2106m PN7138-rev001 Page Table of Contents Configuring the MES1A/B Modbus Basics Manual Documentation Number MES1A/MES1B-2106m Support About Your MES1A/B Converter IntroductionAbout this Manual Features Power LED Package ChecklistIndicators, Switches and Connectors Hardware OverviewActivity LED Reset SwitchLink LED DB-9M Serial Port Connector MES1A only RS-422/485 Switch MES1B onlyEthernet Port Connector RS-422/485 Connector MES1B onlyRS-422/485 Four-Wire Mode RS-485 Two-Wire ModeConnecting the Hardware Power ConnectorMES1A Connections MES1B Connections Hardware Overview Getting Started QuickStartDiscover the MES1A/B on the Network System Requirements Using the Device Installer SoftwareInstalling the Device Installer Starting the Device Installer Discovering DevicesDevice Installer Main Window Getting Device DetailsConnecting to the MES1A/B Press Enter to go into Setup ModeTelnet Configuration Tab with Settings Getting Started Configuring the MES1A/B Telnet Configuration TabNavigating the Configuration Menu Unit ID to IP Address TableTo Reconfigure the MES1A to Factory Settings Saving Configuration SettingsReconfiguring to Factory Settings To Reconfigure the MES1B, to Factory SettingsNetwork/IP Settings IP AddressStatic IP Address Default GatewayAuto-IP Netmask Serial and Mode SettingsTelnet Configuration Password Serial Protocol ProtocolAttached Device MES1B Serial Interface Serial InterfaceMES1A Serial Interface Modem/Configurable Pin Settings Serial ParametersAdvanced Modbus Protocol Settings Advanced Modbus Protocol Settings Menu…255 Slave Address / Unit ID SourceFor Auto = No Allow Modbus BroadcastsUse MB/TCP 00BH/00AH Exception Responses = YesMessage Timeout Disable Modbus/TCP PipelineCharacter Timeout Swap 4x/0H to Get 3x/1x Unit ID to IP Address Lookup Table SettingsSerial TX Delay after RX Close Idle TCP Sockets AfterModbus Address From/To Redundant Entry Retries AfterAdd, Delete, Exit Select Function Slave IP Address Creating a New Device List Using Other Device Installer FeaturesManaging Device Lists Opening Device Lists Display Devices Using IconsSaving Device Lists Device List Display OptionsDisplay the Device Name Adding a Device ManuallyDisplay the Hardware MAC Address Assigning an IP Address using Device Installer Using Device Installer to Assign an IP AddressUsing the Devices Details Tab Upgrading Firmware Adding Info to the Device Details TabInstalling Pre-Saved Configuration Files Saving Setup RecordsInstalling Setup Records Save Setup Records Dialog BoxLogging Search and Upgrade Data Options Window, Customization Tab Using Ping Using HelpUsing Other Device Installer Features Modbus Basics Modbus ASCII/RTUModbus/TCP Hints and Tips Modbus Basics Appendix a Default Configuration Settings Swap 4x/0H to get 3x/1xDefault Configuration Settings Appendix B Product Specifications Manual CD-ROM discProduct Specifications Appendix C Dimensional Diagrams Dimensional Diagram of the MES1ADimensional Diagram of the MES1B Appendix D Serial Connections DTEMES1B Terminal Block Pin-out for RS-485 Two-Wire Operation RJ-45 Pin Signal Wire Color Appendix E Network ConnectionsNetwork Connections Declaration of Conformity