B&B Electronics MES1A, MES1B manual Modem/Configurable Pin Settings, Serial Parameters

Page 37

Configuring the MES1A/B

30. To accept changes, press Enter

When RS-422/485 four-wire operation is selected:

When RS-422/485four-wire operation is selected the RS-422/485 switch on the MES1B must be in the left position.

When RS-485 two-wire operation is selected:

CP1 (configured in the next section under Modem/Configurable Pin Settings) must be enabled to ensure Send Data control is implemented.

The RS-422/485 switch on the MES1B must be in the right position.

The multidrop bus is connected to Terminals 3 [DataB(+) to TDB(+) terminal] and 4 [DataA(-) to TDA(-) terminal].

No jumpers are required to bridge transmit and receive lines on the terminal block

Serial Parameters

MES1A/B Serial Parameters must be set up to match the parameters of the Modbus device connected to its serial interface. MES1A/B Serial Parameter options include:

Data rates from 300 bps to 115200 bps

7 or 8 data bits

No, Even or Odd parity

1 or 2 stop bits.

To configure Serial Parameters:

31.At the Enter serial parameters (9600,8,N,1)prompt

o To keep the current setting, press Enter

o To change the serial parameters, type in new parameters in the format 9600,8,N,1

32.To accept changes, press Enter

3)Modem/Configurable Pin Settings

There is only one configurable setting required in the Modem/Configurable Pin Settings section of the Configuration Menu. When configuring an

Manual Documentation Number: MES1A/MES1B-2106m

PN7138-rev001

B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104www.bb-elec.com

B&B Electronics Ltd – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445www.bb-europe.com

27

Image 37
Contents Models MES1A, MES1B Modbus TCP Modbus Ascii / RTU ConvertersManual Documentation Number MES1A/MES1B-2106m International Headquarters Page Manual Documentation Number MES1A/MES1B-2106m PN7138-rev001 Page Table of Contents Configuring the MES1A/B Modbus Basics Manual Documentation Number MES1A/MES1B-2106m About this Manual IntroductionSupport About Your MES1A/B Converter Features Indicators, Switches and Connectors Package ChecklistPower LED Hardware OverviewLink LED Reset SwitchActivity LED Ethernet Port Connector RS-422/485 Switch MES1B onlyDB-9M Serial Port Connector MES1A only RS-422/485 Connector MES1B onlyRS-485 Two-Wire Mode RS-422/485 Four-Wire ModePower Connector Connecting the HardwareMES1A Connections MES1B Connections Hardware Overview QuickStart Getting StartedDiscover the MES1A/B on the Network Installing the Device Installer Using the Device Installer SoftwareSystem Requirements Discovering Devices Starting the Device InstallerGetting Device Details Device Installer Main WindowPress Enter to go into Setup Mode Connecting to the MES1A/BTelnet Configuration Tab with Settings Getting Started Telnet Configuration Tab Configuring the MES1A/BUnit ID to IP Address Table Navigating the Configuration MenuReconfiguring to Factory Settings Saving Configuration SettingsTo Reconfigure the MES1A to Factory Settings To Reconfigure the MES1B, to Factory SettingsIP Address Network/IP SettingsAuto-IP Default GatewayStatic IP Address Telnet Configuration Password Serial and Mode SettingsNetmask Attached Device ProtocolSerial Protocol MES1A Serial Interface Serial InterfaceMES1B Serial Interface Serial Parameters Modem/Configurable Pin SettingsAdvanced Modbus Protocol Settings Menu Advanced Modbus Protocol SettingsFor Auto Slave Address / Unit ID Source…255 Use MB/TCP 00BH/00AH Exception Responses Allow Modbus Broadcasts= No = YesCharacter Timeout Disable Modbus/TCP PipelineMessage Timeout Serial TX Delay after RX Unit ID to IP Address Lookup Table SettingsSwap 4x/0H to Get 3x/1x Close Idle TCP Sockets AfterAdd, Delete, Exit Select Function Redundant Entry Retries AfterModbus Address From/To Slave IP Address Managing Device Lists Using Other Device Installer FeaturesCreating a New Device List Saving Device Lists Display Devices Using IconsOpening Device Lists Device List Display OptionsDisplay the Hardware MAC Address Adding a Device ManuallyDisplay the Device Name Using Device Installer to Assign an IP Address Assigning an IP Address using Device InstallerUsing the Devices Details Tab Adding Info to the Device Details Tab Upgrading FirmwareSaving Setup Records Installing Pre-Saved Configuration FilesSave Setup Records Dialog Box Installing Setup RecordsLogging Search and Upgrade Data Options Window, Customization Tab Using Help Using PingUsing Other Device Installer Features Modbus ASCII/RTU Modbus BasicsModbus/TCP Hints and Tips Modbus Basics Swap 4x/0H to get 3x/1x Appendix a Default Configuration SettingsDefault Configuration Settings Manual CD-ROM disc Appendix B Product SpecificationsProduct Specifications Dimensional Diagram of the MES1A Appendix C Dimensional DiagramsDimensional Diagram of the MES1B DTE Appendix D Serial ConnectionsMES1B Terminal Block Pin-out for RS-485 Two-Wire Operation Appendix E Network Connections RJ-45 Pin Signal Wire ColorNetwork Connections Declaration of Conformity