B&B Electronics MES1B, MES1A manual Network/IP Settings, IP Address

Page 32

Configuring the MES1A/B

16.Type 3 to enter the Modem/Configurable Pin Settings section and set CP1 to RS-485 Enable Wire (see the next section for details)..

See the following sections for details on how to set Serial & Mode Settings and

Modem/Configurable Pin Settings.

1) Network/IP Settings

In the Network/IP Settings section of the Configuration Menu you can configure:

•IP Address of the MES1A/B

•Default Gateway

•Netmask

•Telnet Configuration Password

IP Address

Every device connected to a TCP/IP network must have a unique IP Address. This includes every MES1A/B. However, there is more than one way to set up an IP address for the MES1A/B

DHCP

The MES1A/B is shipped with a default IP address of 0.0.0.0. This configures the converter to obtain an IP address via DHCP (Dynamic Host Configuration Protocol) from a DHCP server on the network when the MES1A/B boots up.

If a DHCP server is available to respond to the DHCP request, the MES1A/B will receive an IP address, gateway address and subnet mask from the server.

A DHCP-generated IP address will appear in the Device Tree, Device List and at the top of the Telnet Configuration tab, but it will not be displayed in the IP Address field of the Network/IP Settings section of the Configuration Menu.

Figure 16. Network/IP Settings Menu

Manual Documentation Number: MES1A/MES1B-2106m

PN7138-rev001

B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104 – www.bb-elec.comB&B Electronics Ltd – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445 – www.bb-europe.com

22

Image 32

Contents Modbus TCP Modbus Ascii / RTU Converters Models MES1A, MES1BManual Documentation Number MES1A/MES1B-2106m International Headquarters Page Manual Documentation Number MES1A/MES1B-2106m PN7138-rev001 Page Table of Contents Configuring the MES1A/B Modbus Basics Manual Documentation Number MES1A/MES1B-2106m Support About Your MES1A/B Converter IntroductionAbout this Manual Features Package Checklist Indicators, Switches and ConnectorsPower LED Hardware OverviewActivity LED Reset SwitchLink LED RS-422/485 Switch MES1B only Ethernet Port ConnectorDB-9M Serial Port Connector MES1A only RS-422/485 Connector MES1B onlyRS-422/485 Four-Wire Mode RS-485 Two-Wire ModeConnecting the Hardware Power ConnectorMES1A Connections MES1B Connections Hardware Overview Getting Started QuickStartDiscover the MES1A/B on the Network System Requirements Using the Device Installer SoftwareInstalling the Device Installer Starting the Device Installer Discovering DevicesDevice Installer Main Window Getting Device DetailsConnecting to the MES1A/B Press Enter to go into Setup ModeTelnet Configuration Tab with Settings Getting Started Configuring the MES1A/B Telnet Configuration TabNavigating the Configuration Menu Unit ID to IP Address TableSaving Configuration Settings Reconfiguring to Factory SettingsTo Reconfigure the MES1A to Factory Settings To Reconfigure the MES1B, to Factory SettingsNetwork/IP Settings IP AddressStatic IP Address Default GatewayAuto-IP Netmask Serial and Mode SettingsTelnet Configuration Password Serial Protocol ProtocolAttached Device MES1B Serial Interface Serial InterfaceMES1A Serial Interface Modem/Configurable Pin Settings Serial ParametersAdvanced Modbus Protocol Settings Advanced Modbus Protocol Settings Menu…255 Slave Address / Unit ID SourceFor Auto Allow Modbus Broadcasts Use MB/TCP 00BH/00AH Exception Responses= No = YesMessage Timeout Disable Modbus/TCP PipelineCharacter Timeout Unit ID to IP Address Lookup Table Settings Serial TX Delay after RXSwap 4x/0H to Get 3x/1x Close Idle TCP Sockets AfterModbus Address From/To Redundant Entry Retries AfterAdd, Delete, Exit Select Function Slave IP Address Creating a New Device List Using Other Device Installer FeaturesManaging Device Lists Display Devices Using Icons Saving Device ListsOpening Device Lists Device List Display OptionsDisplay the Device Name Adding a Device ManuallyDisplay the Hardware MAC Address Assigning an IP Address using Device Installer Using Device Installer to Assign an IP AddressUsing the Devices Details Tab Upgrading Firmware Adding Info to the Device Details TabInstalling Pre-Saved Configuration Files Saving Setup RecordsInstalling Setup Records Save Setup Records Dialog BoxLogging Search and Upgrade Data Options Window, Customization Tab Using Ping Using HelpUsing Other Device Installer Features Modbus Basics Modbus ASCII/RTUModbus/TCP Hints and Tips Modbus Basics Appendix a Default Configuration Settings Swap 4x/0H to get 3x/1xDefault Configuration Settings Appendix B Product Specifications Manual CD-ROM discProduct Specifications Appendix C Dimensional Diagrams Dimensional Diagram of the MES1ADimensional Diagram of the MES1B Appendix D Serial Connections DTEMES1B Terminal Block Pin-out for RS-485 Two-Wire Operation RJ-45 Pin Signal Wire Color Appendix E Network ConnectionsNetwork Connections Declaration of Conformity