RAD Data comm AMC-101 operation manual Installation, Two Units

Page 27

AMC-101Installation & Operation Manual

Chapter 2 - Installation & Setup

 

 

Installation of

Rack adapter components for installing two units include two long side rails

Two Units

(one for each unit) which slide one into the other fastening the two units

 

together, and two short side brackets which hold the two units in the

19'' rack (see Figure 2-4).

Figure 2-4 Installation of Two Units (a)

To install two units follow these instructions:

1.Fasten one long side rail to each unit (right side to one unit, left side to the other unit) using the four screws and flat washers supplied. The side rails must be attached in opposing fashion, the narrow flange of the first rail opposite the wide flange of the second rail.

2.Attach one short bracket opposite the side rail on each unit using the four screws and flat washers supplied.

3.Slide the side rail of one unit into the side rail of the other unit, fastening the two units together (see Figure 2-5).

4.Secure the supplied plastic caps to the ends of the rails, to prevent the units moving and to protect the rail ends.

5.Place the assembled units in the rack and fasten the brackets to the side rails of the rack, by means of the four screws situated on each side (not included in the kit).

Site Requirements

2-3

Image 27
Contents AMC-101 Page Warranty Safety Warnings Regulatory Information Declaration of Conformity Contents Operation List of Figures List of Tables Retimed Modules Transparent GeneralSTP UTP FeaturesDissimilar Device Connectivity General ApplicationsWrap Dual Single Mode SM to Multimode MM Conversion Fddi and Fast Ethernet Operations Fast Ethernet Applications ProblemRepeater Half Duplex Connection over UTP 10 Point-to-Point Full Duplex Connection 12 Full Duplex Connection over UTP Specifications Optical Module Characteristics 0.25 dB/Km for 1550 nm modules Electrical Module Characteristics Introduction Specifications Site Requirements UnpackingInstallation of a Two Units InstallationAC Power Connection Cable ConnectionsGrounding MM/SC/13/R Module AMC-101 ModulesMM/SC/13/T Module Front Panel MM/SC/13/T ModuleMM/ST/13/R Module Front Panel MM/ST/13/R ModuleMM/ST/13/T Module Front Panel MM/ST/13/T Module10 SM/ST/13/R Module Front Panel SM/ST/13/R Module11 SM/ST/13/T Module Front Panel SM/ST/13/T Module12 SM/FC/13/T Module Front Panel SM/FC/13/T Module13 SM/ST/13L/R Module Front Panel SM/ST/13L/R Module14 SM/ST/13L/T Module Front Panel SM/ST/13L/T Module15 SM/SC/13L/R Module Front Panel SM/SC/13L/R Module16 SM/ST/13LH/R Module Front Panel SM/ST/13LH/R Module17 SM/FC/13LH/R Module Front Panel SM/FC/13LH/R Module18 SM/ST/15L/R Module Front Panel SM/ST/15L/R Module19 SM/ST/15LH/R Module Front Panel SM/ST/15LH/R Module20 SM/FC/15LH/R Module Front Panel SM/FC/15LH/R Module21 MM/ST/85/T Module Front Panel MM/ST/85/T Module22 SF1/ST/R Module Front Panel SF1/ST/R Module23 SF2/ST/R Module Front Panel SF2/ST/R Module24 SF1/FC/R Module Front Panel SF1/FC/R Module25 SF2/FC/R Module Front Panel SF2/FC/R ModuleBNC CX/BNC/155/R Module27 CX/DIN/155/R Module Front Panel CX/DIN/155/R Module28 STP/155/R Module Front Panel STP/155/R Module29 STP/155/T Module Front Panel STP/155/T Module30 UTP/155/R Module Front Panel UTP/155/R Module31 UTP/155/T Module Front Panel UTP/155/T Module32 UTP/100/R Module Front Panel UTP/100/R Module33 UTP/100/T Module Front Panel UTP/100/T Module34 100BT/B 100BT/B Module35 100BT/R Module Front Panel 100BT/R Module36 10BT/B Module Front Panel 10BT/B ModuleChapter Operation Controls and IndicatorsJumper Locations and Functions DC adapter Connection Dry Contact Circuit and Connector for AlarmsExample Turning on the AMC-101AMC-101 Block Diagram Troubleshooting Procedures Normal OperationTurning off the AMC-101