Motorola DCT1800 installation manual

Page 2

Graphical symbols and supplement warning marking locations on the bottom of the appliance.

This symbol indicates that dangerous voltage levels are present within the equipment. These voltages are not insulated and may be of sufficient strength to cause serious bodily injury when touched. The symbol may also appear on schematics.

This symbol calls attention to a critical procedure, or means refer to the instruction manual for opening or service information. Only qualified service personnel are to install or service the equipment. The symbol may also appear in text and on schematics.

WARNING:

TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.

CAUTION:

TO PREVENT ELECTRICAL SHOCK, DO NOT USE THIS PLUG WITH AN EXTENSION CORD, RECEPTACLE, OR OTHER OUTLET UNLESS THE BLADES CAN BE FULLY INSERTED TO PREVENT BLADE EXPOSURE.

FCC Compliance: Federal Communications Commission Radio and Television Interface Statement for a Class ‘B’ Device

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in the residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.

If the equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

!Reorient or relocate the receiver antenna

!Increase the separation between the equipment and the affected receiver

!Connect the equipment into an outlet or on a circuit different from that to which the receiver is connected

!Consult the dealer or experienced radio/TV technician for help

!Ensure that the cover plate for the security card is secured and tight

Changes or modification not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Declaration of Conformity: According to 47 CFR, Parts 2 and 15 for Class B Personal Computers and Peripherals; and/or CPU Boards and Power Supplies used with Class B Personal Computers, Motorola, Inc., 6450 Sequence Drive, San Diego, CA 92121, 1-800-225-9446, declares under sole responsibility that the product identifies with 47 CFR Part 2 and 15 of the FCC Rules as a Class B digital device. Each product marketed is identical to the representative unit tested and founded to be compliant with the standards. Records maintained continue to reflect the equipment being produced can be expected to be within the variation accepted, due to quantity production and testing on a statistical basis as required by 47 CFR 2.909. Operation is subject to the following condition: This device must accept any interference received, including interference that may cause undesired operation. The above named party is responsible for ensuring that the equipment complies with the standards of 47 CFR, Paragraphs 15.107 to 15.109

Page 1 Page 3
Image 2
Page 1 Page 3
Contents Installation Manual DCT1800 Page Page Contents Diagnostics TroubleshootingSpecifications Abbreviations and AcronymsFigures Tables Introduction DCT1800 advanced set-topDocument Conventions Using This ManualRelated Documentation If You Need Help Calling for RepairsDCT1800 front panel OverviewFront Panel Function Rear PanelKeyItem DCT1800 rear panelRemote Controls Motorola universal remote controlKeyItemDescription Installing Batteries in Remote Control Back view of remote controlBefore You Begin InstallationInstalling the DCT1800 Standard Cabling Diagram Standard cablingStandard VCR Cabling Diagram Standard VCR cablingComposite Baseband Cabling Diagrams Standard baseband cablingComposite VCR cabling Stereo Cabling Diagram Baseband Audio through the VCRAudio through VCR/audio output on TV Receiver Cabling Diagrams Audio through A/V ReceiverCold Initialization Feature Testing ProcedureOperational Check Possible Solution TroubleshootingProblem Specifications Ac voltage Power dissipationWeight Surge protectionDiagnostics Accessing DiagnosticsCursor UP Navigating the DiagnosticsCH/CUR + Cursor Down Cursor RightGeneral Status Figure B-2 DCT1800 StatusField Description Initialization Status Errors Code Flash Sequence EMM Out-of-Band OOB StatusYES FIXCUR Freq LKCEMM Data Indicator Table B-5 In-band Diagnostic FieldsData Activity Indicator In-band StatusFair SNRGood PoorAudio/Video Status Status DescriptionDCT1800 Unit Address Unit AddressTable B-7 Unit Address Fields Network AddressSeed Health Firmware VersionMulticast 16 Address Current Channel Status Figure B-8 Current Channel StatusTable B-8 Current Channel Status Fields AuthorizationService TypeOSD Variable State Table B-9 Current Channel Status VariablesTvpc Required / Not Required Renewable Security SystemTable B-10 Renewable Security Fields CryptoDisabled Upstream Modem Starvue II DiagnosticsEnabled IppvModule Application APP Code ModulesTable B-12 APP Code Modules Fields Memory Status UPM Interactive InfoTable B-14 Interactive Info Fields Upstream IDMAC Frequency Table Message Types Task Status In-band Program Association Table PATIn-band Program Map Table PMT In-band Multicast Address Filter Keyboard / LED Diagnostics Figure B-20 Keyboard / LED DiagnosticsMgbi
Top Page Image Contents