Motorola DCT1800 Operational Check, Cold Initialization, Feature Testing Procedure

Page 24

Installation3-9

Operational Check

The operational check tests the communication link between the remote control and the DCT1800. The procedures verify the DCT1800 response to remote control commands. Table 3-1 lists the operational check procedures:

Table 3-1

Operational check

Feature

Testing Procedure

Power on

! Press POWER to turn on the DCT1800.

 

! Turn on the TV and tune it to the output channel of the DCT1800 (channel 3

 

or 4).

Channel Selection

Tune to several channels by entering the channel number with the numeric keys on

 

the remote control.

If the DCT1800 does not operate properly, refer to Section 4, “Troubleshooting” .

Cold Initialization

The DCT1800 has no front panel buttons. To perform a cold initialization, or reset, use the remote control.

To execute a cold initialization:

1Hold down any key on the remote control while disconnecting and reconnecting AC power to the DCT1800.

After booting up, the POWER LED on the DCT1800 front panel will flash.

2Within 3 seconds, press the 3 key on the remote control.

The POWER LED on the DCT1800 front panel flashes at a decreased rate.

3Within 3 seconds, press the 2 key on the remote control.

The POWER LED on the DCT1800 front panel flashes at an increased rate.

4Within 3 seconds, press the 8 key on the remote control to initiate the cold reset.

During the cold initialization procedure, if the appropriate remote control key is not pressed within the three-second time period, the procedure terminates and the DCT1800 resumes normal operation.

DCT1800 Installation Manual

Image 24
Contents Installation Manual DCT1800 Page Page Contents Troubleshooting SpecificationsDiagnostics Abbreviations and AcronymsFigures Tables Introduction DCT1800 advanced set-topUsing This Manual Related DocumentationDocument Conventions If You Need Help Calling for RepairsOverview Front PanelDCT1800 front panel Rear Panel KeyItemFunction DCT1800 rear panelRemote Controls Motorola universal remote controlKeyItemDescription Installing Batteries in Remote Control Back view of remote controlInstallation Installing the DCT1800Before You Begin Standard Cabling Diagram Standard cablingStandard VCR Cabling Diagram Standard VCR cablingComposite Baseband Cabling Diagrams Standard baseband cablingComposite VCR cabling Stereo Cabling Diagram Baseband Audio through the VCRAudio through VCR/audio output on TV Receiver Cabling Diagrams Audio through A/V ReceiverFeature Testing Procedure Operational CheckCold Initialization Troubleshooting ProblemPossible Solution Specifications Power dissipation WeightAc voltage Surge protectionDiagnostics Accessing DiagnosticsNavigating the Diagnostics CH/CUR +Cursor UP Cursor Down Cursor RightGeneral Status Figure B-2 DCT1800 StatusField Description Initialization Status Errors Code Flash Sequence Out-of-Band OOB Status YESEMM FIXCUR Freq LKCTable B-5 In-band Diagnostic Fields Data Activity IndicatorEMM Data Indicator In-band StatusSNR GoodFair PoorAudio/Video Status Status DescriptionUnit Address Table B-7 Unit Address FieldsDCT1800 Unit Address Network AddressFirmware Version Multicast 16 AddressSeed Health Current Channel Status Figure B-8 Current Channel StatusAuthorization ServiceTable B-8 Current Channel Status Fields TypeOSD Variable State Table B-9 Current Channel Status VariablesRenewable Security System Table B-10 Renewable Security FieldsTvpc Required / Not Required CryptoUpstream Modem Starvue II Diagnostics EnabledDisabled IppvApplication APP Code Modules Table B-12 APP Code Modules FieldsModule Memory Status Interactive Info Table B-14 Interactive Info FieldsUPM Upstream IDMAC Frequency Table Message Types In-band Program Association Table PAT In-band Program Map Table PMTTask Status In-band Multicast Address Filter Keyboard / LED Diagnostics Figure B-20 Keyboard / LED DiagnosticsMgbi