Pioneer VSX-D711, VSX-D811S manual Connecting up AC outlet, Operating other Pioneer components

Page 25

Connecting up

03

AC outlet

 

 

 

 

 

 

 

 

 

 

 

 

[switched 100 W (0.8 A) max]

 

 

 

 

 

 

Power supplied through this outlet is turned on and off by the

 

 

 

 

 

 

receiver's POWER switch. Total electrical power consumption of

 

AC OUTLET

 

connected equipment should not exceed 100 W (0.8 A).

 

SWITCHED

 

 

 

100 W MAX

 

 

 

 

 

0.8 A MAX

 

DO NOT CONNECT A MONITOR, TV SET, HEATER, OR SIMILAR

 

 

 

 

 

 

APPLIANCE TO THIS UNIT'S AC OUTLET.

 

 

 

 

 

 

Do not connect appliances with high power consumption to the

 

 

 

 

 

 

AC OUTLET in order to avoid overheating and fire risk. This can

 

 

 

 

 

 

 

 

 

 

 

 

also cause the receiver to malfunction.

 

 

 

 

 

 

•Make sure no exposed speaker wire is touching the rear panel, this may cause the receiver to turn off automatically.

•This unit should be disconnected by removing the power plug from the wall socket when not in regular use (ex. when on vacation).

POWER-CORD CAUTION

Handle the power cord by the plug. Do not pull out the plug by tugging the cord and never touch the power cord when your hands are wet as this could cause a short circuit or an electric shock. Do not place the unit, a piece of furniture, etc., on the power cord, or pinch the cord. Never make a knot in the cord or tie it with other cords. The power cords should be routed such that they are not likely to be stepped on. A damaged power cord can cause a fire or give you an electrical shock. Check the power cord once in a while. When you find it damaged, ask your nearest Pioneer authorized service center or your dealer for a replacement.

Operating other Pioneer components

By connecting a control cord (optional), you can point the remote controls of other Pioneer components at the receiver’s remote sensor. The remote control signals are received by the remote sensor of this unit, and sent to the other devices via the

CONTROL

IN

OUT CONTROL

OUT

CONTROL OUT terminal.

Receiver

Remote control unit

Other Pioneer products with Î mark

Connect to CONTROL IN terminal of other Pioneer products with Î mark.

25

En

XRB3013A.13.25

25

01.12.12, 4:43 PM

Page 24 Page 26
Image 25
Page 24 Page 26
Contents VSX-D711 VSX-D811S Important Notice XRB3013A.01.06 01.12.12, 441 PM Contents Making a recording Operating range of remote control unit Installing the receiverBefore you start Checking what’s in the box Making cable connectionsMinute guide Introduction to home theater Hook up your DVD player 02 5 minute guide Listening to Surround SoundHook up your TV Connect your speakers Minute guideSBL SBR 02 5 minute guidePlay a DVD, and adjust the volume to your liking Press Quick Setup 02 5 minute guide Using the Quick Setup1ch 0chAudio/Video cords Connecting upVideo cables Component video cordsVSX-D711 Connecting up Connecting digital componentsVSX-D811S CD player Connecting up Connecting audio componentsVideo Connecting up Connecting DVD 5.1 channel componentsConnecting to the front panel video terminal Connecting up Connecting video componentsFM wire antenna Connecting up Connecting antennasAM loop antenna Connecting up Connecting the speakers VSX-D711 To 16 Ω Connecting up Connecting the speakers VSX-D811SBe sure to complete Speaker terminals Hints on speaker placementB speaker systems View of speaker set up VSX-D811S VSX-D811S only Connecting up Connecting additional amplifiersOperating other Pioneer components Connecting up AC outletAppliance to this Units AC Outlet Control OUT terminalControls and Displays Front panel Master VolumeSTANDBY/ON EnterDisplay Controls and DisplaysDTS AnalogPRO Logic ATTSource Controls and Displays Remote controlRCV DISPLAY/DISC EnterDTV ON/OFF DTV InfoDTV Menu TOP MenuMute TV Volume +TV Input LED DisplayPlaying sources Introduction to Sound Modes Standard modeStereo/Direct Advanced Surround modes Playing sourcesSources with stereo surround Analog 2-channel stereo sourceListening to multi-channel playback Playing sources Choosing the input signalUsing Advanced Surround Using Stereo/DirectNEO6 Start playback of the component you selected in stepUsing the tone controls Playing sources Using Loudness and Midnight listeningPlaying other sources TrebleDVD Playing sources Selecting the multi-channel analog inputsSetting up the receiver Choosing your receiver setup Speaker setting Setting up the receiverFL-C FS-CS-S FL-CS-SFL-CL-SL FL-CS-SS FL-CL-SS FL-CS-SL FL-CL-SChannel setting Surround back speaker settingSubwoofer setting Crossover frequency settingLFE attenuator setting Center speaker distance settingFront speaker distance setting Surround speaker distance set- tingDynamic range control setting Surround back speaker distance settingDual mono setting Component video input settingsCoaxial digital input settings Surround back channel input settingOptical digital input settings SB 2ch Use ’ or ‘ to select SB 2ch in or SB 1chUse Level +/- to adjust the speaker levels in turn Setting the relative volume level of each channelWhen you’re done, press Test Tone to turn off the test tone FL C FR SW SL SBTuning directly to a station Using the tuner Listening to the radioImproving FM stereo sound Saving station presets Using the tunerTune to a station you want to memo Rize Press T.EDIT Tuner EditListening to station presets Using the tuner Naming station presetsChoose the station preset you want to name Input the name you wantMonitoring your recording Making Recordings Making an audio or a video recordingSelecting preset codes directly Setting the remote to control other componentsProgramming signals from other remote controls Searching for preset codesSwitch on the component you want to control Press Remote Setup and hold for three secondsClearing all the remote control settings Erasing one of the remote control button settingsPrepare the remote to erase the button setting Press and hold the button to be erased for three secondsDirect function Confirming preset codesChannel Controlling the rest of your system Controls for TVsTV VOL SUB TitleControls for other components Controlling the rest of your systemMenu DisplayEnter Channel Manufacturer Code Controlling the rest of your system Preset Code List1013, 1019, 1026, 1027 1055, 1086, 10891032, 1063 1036, 1086 10961013, 1019 11141017, 1032, 1089 10141006, 1079 10591132 1055, 1073LD Player MD PlayerCD Player DVD Player Tape DeckMisc Audio AmplifierReceivers VCR 2015, 2042 2015, 2027, 20322017, 2018, 2053 2001, 2017, 2034, 2059 2062, 2085, 2087Satellite Tuner 4008 40154005 4034Cable TV Adjust the Master Volume Additional information TroubleshootingPlace the antenna farther away from the equipment causing ReceiverFront panel refer to Additional informationRemove the obstacle or operate from another position LightAmplifier Section Additional information SpecificationsVideo Section FM Tuner SectionFurnished Parts MiscellaneousWe Want You Listening For a Lifetime Additional information Additional information Additional information TNGZF/01L00001 Printed XRB3013-A 0 4 2 1 1 4 0
Top Page Image Contents