Pioneer VSX-D711 Setting the remote to control other components, Selecting preset codes directly

Page 49

Controlling the rest of your system

Setting the remote to control other components

There are several ways to set your remote to control the other components in your system. The easiest way to do this is to assign the component’s manufacturer preset code (listed on pages 56–67) to one of the MULTI CONTROL buttons on the remote control.

The buttons can be set to control the following components:

	Button	Controllable Components
	Button	Controllable Components

	DVD:	DVD or LD player
	TV:	TV or Satellite tuner
	VCR:	VCR or Digital Video Recorder
	CD:	CD player
	CD-R:	CD Recorder, Tape deck
		or MD player
	TVC:	TV or Cable TV tuner
	TUN:	FM/AM tuner

You can do this directly, or by searching through different preset codes until you find the right one. If you can’t find a preset code that matches the component you want to control, you can still teach the remote individual commands from another remote control (page 50).

You can cancel or exit any of the steps by pressing and holding MUTE for three seconds.

XRB3013A.49.67

49

09

Selecting preset codes directly

SOURCE			RECEIVER
DVD		TV	VCR		CD-R
		MULTI CONTROL
RCV		CD	TUN		TVC
1		2			3
TEST TONE		INPUT ATT		FL DIMMER
4		5			6
CH SELECT			LEVEL
7		8			9
+10			EFFECT		DISPLAY
		0			DISC
		0		ENTER
DTV INFO	MPX/RETURN		D.ACCESS		T.EDIT/GUIDE
¶		7	3		8
BAND		CLASS	DTV ON/OFF		DTV MENU
1		¡	4		¢
TOP MENU		AUDIO	SUB TITLE		ANGLE
REMOTE SETUP	STANDARD		ADV.SURR.		STEREO
INPUT SEL.	SIGNAL SEL		MIDNIGHT/		MUTE
INPUT SEL.	SIGNAL SEL		LOUDNESS		MUTE
		RECEIVER CONTROL
		TUNE
ST		SETUP			ST
ST					ST

ENTER

TUNE

CHANNEL

1Press and hold REMOTE SETUP for three seconds.

The LED lights steadily for two seconds.

2Press the MULTI CONTROL button for the component you want to control.

3Use the number buttons to enter the 4 digit preset code (see pages 56–67)

The LED blinks for half a second after you input each digit and shows a long, two second blink once you have entered a valid code. If the LED blinks three times it means an invalid code has been input or an error has occurred.

•If you assign a preset code for the TUNER button, you won’t be able to control the built-in tuner of this receiver using the remote. Reset the remote to the built-in tuner by entering the preset code 7008.

4Repeat steps 1 through 3 for the other components you want to control.

49

En

01.12.12, 4:48 PM

Image 49

Contents VSX-D711 VSX-D811S Important Notice XRB3013A.01.06 01.12.12, 441 PM Contents Making a recording Operating range of remote control unit Installing the receiverBefore you start Checking what’s in the box Making cable connectionsMinute guide Introduction to home theater Hook up your DVD player 02 5 minute guide Listening to Surround SoundHook up your TV Connect your speakers Minute guideSBL SBR 02 5 minute guidePlay a DVD, and adjust the volume to your liking Press Quick Setup 02 5 minute guide Using the Quick Setup1ch 0chAudio/Video cords Connecting upVideo cables Component video cordsVSX-D711 Connecting up Connecting digital componentsVSX-D811S CD player Connecting up Connecting audio componentsVideo Connecting up Connecting DVD 5.1 channel componentsConnecting to the front panel video terminal Connecting up Connecting video componentsFM wire antenna Connecting up Connecting antennasAM loop antenna Connecting up Connecting the speakers VSX-D711 To 16 Ω Connecting up Connecting the speakers VSX-D811SBe sure to complete Speaker terminals Hints on speaker placementB speaker systems View of speaker set up VSX-D811S VSX-D811S only Connecting up Connecting additional amplifiersOperating other Pioneer components Connecting up AC outletAppliance to this Units AC Outlet Control OUT terminalControls and Displays Front panel Master VolumeSTANDBY/ON EnterDisplay Controls and DisplaysDTS AnalogPRO Logic ATTSource Controls and Displays Remote controlRCV DISPLAY/DISC EnterDTV ON/OFF DTV InfoDTV Menu TOP MenuMute TV Volume +TV Input LED DisplayPlaying sources Introduction to Sound Modes Standard modeStereo/Direct Advanced Surround modes Playing sourcesSources with stereo surround Analog 2-channel stereo sourceListening to multi-channel playback Playing sources Choosing the input signalUsing Advanced Surround Using Stereo/DirectNEO6 Start playback of the component you selected in stepUsing the tone controls Playing sources Using Loudness and Midnight listeningPlaying other sources TrebleDVD Playing sources Selecting the multi-channel analog inputsSetting up the receiver Choosing your receiver setup Speaker setting Setting up the receiverFL-C FS-CS-S FL-CS-SFL-CL-SL FL-CS-SS FL-CL-SS FL-CS-SL FL-CL-SChannel setting Surround back speaker settingSubwoofer setting Crossover frequency settingLFE attenuator setting Center speaker distance settingFront speaker distance setting Surround speaker distance set- tingDynamic range control setting Surround back speaker distance settingDual mono setting Component video input settingsCoaxial digital input settings Surround back channel input settingOptical digital input settings SB 2ch Use ’ or ‘ to select SB 2ch in or SB 1chUse Level +/- to adjust the speaker levels in turn Setting the relative volume level of each channelWhen you’re done, press Test Tone to turn off the test tone FL C FR SW SL SBTuning directly to a station Using the tuner Listening to the radioImproving FM stereo sound Saving station presets Using the tunerTune to a station you want to memo Rize Press T.EDIT Tuner EditListening to station presets Using the tuner Naming station presetsChoose the station preset you want to name Input the name you wantMonitoring your recording Making Recordings Making an audio or a video recordingSelecting preset codes directly Setting the remote to control other componentsProgramming signals from other remote controls Searching for preset codesSwitch on the component you want to control Press Remote Setup and hold for three secondsClearing all the remote control settings Erasing one of the remote control button settingsPrepare the remote to erase the button setting Press and hold the button to be erased for three secondsDirect function Confirming preset codesChannel Controlling the rest of your system Controls for TVsTV VOL SUB TitleControls for other components Controlling the rest of your systemMenu DisplayEnter Channel Manufacturer Code Controlling the rest of your system Preset Code List1013, 1019, 1026, 1027 1055, 1086, 10891032, 1063 1036, 1086 10961013, 1019 11141017, 1032, 1089 10141006, 1079 10591132 1055, 1073LD Player MD PlayerCD Player DVD Player Tape DeckMisc Audio AmplifierReceivers VCR 2015, 2042 2015, 2027, 20322017, 2018, 2053 2001, 2017, 2034, 2059 2062, 2085, 2087Satellite Tuner 4008 40154005 4034Cable TV Adjust the Master Volume Additional information TroubleshootingPlace the antenna farther away from the equipment causing ReceiverFront panel refer to Additional informationRemove the obstacle or operate from another position LightAmplifier Section Additional information SpecificationsVideo Section FM Tuner SectionFurnished Parts MiscellaneousWe Want You Listening For a Lifetime Additional information Additional information Additional information TNGZF/01L00001 Printed XRB3013-A 0 4 2 1 1 4 0