Pioneer VSX-D711 Erasing one of the remote control button settings, Repeat to erase other buttons

Page 51

Controlling the rest of your system

4Point the two remote controls towards each other about 1-2 inches apart then press the button that will be doing the learning on this receiver’s remote control (for example 3, 7, etc.).

The LED flashes rapidly.

1 - 2 inches

3

6

9

8

¢

 

 

 

 

3

4

 

2

5

8

0

 

 

 

 

 

7

¡

 

1

4

7

 

1

 

 

 

 

5Press the corresponding button on the other remote control that is sending (teaching) the signal to this receiver’s remote control (for example 3, 7, etc.).

If the operation has been learned successfully, the LED on this receiver’s remote will go out and then light steadily.

If for some reason the operation hasn’t been learned the LED will blink for three seconds and then light steadily. If this happens, keep pressing the (teaching) button as you vary the distance between the two remotes, until you see the the LED light steadily.

To program additional operations for the current component repeat steps 4 and 5.

To program operations for another component exit and repeat steps 1 through 5.

6Press and hold the REMOTE SETUP button for three seconds to store the operation(s).

•Some commands from other remote controls cannot be learned, but in most cases the remotes just need to be moved closer together or farther apart.

•Certain buttons represent operations that cannot be learned from other remote

controls. These include: RECEIVER , REMOTE SETUP and the MULTI

CONTROL, RECEIVER CONTROL and MASTER VOLUME buttons.

09

•TV CONTROL buttons (TV , TV VOL +/-, and TV INPUT) can only be learned after selecting TV or TVC.

Erasing one of the remote control button settings

(VSX-D811S only)

This erases one of the buttons you have programmed and restores the button to the factory default.

1Press REMOTE SETUP and hold for three seconds.

The LED lights steadily for two seconds.

2Press the MULTI CONTROL button relating to the button setting to be erased.

3Prepare the remote to erase the button setting.

Press the RECEIVER button twice quickly.

The LED blinks to indicate the remote is ready to erase the button setting.

4Press and hold the button to be erased for three seconds.

The LED lights steadily for three seconds and then goes off.

5Repeat step 4 to erase other buttons.

6Press and hold the REMOTE SETUP button for two seconds to exit.

Clearing all the remote control settings

You can clear all presets and restore the factory default settings.

1Press REMOTE SETUP and hold for three seconds.

The LED lights steadily for two seconds.

51

En

XRB3013A.49.67

51

01.12.12, 4:49 PM

Page 50 Page 52
Image 51
Page 50 Page 52
Contents VSX-D711 VSX-D811S Important Notice XRB3013A.01.06 01.12.12, 441 PM Contents Making a recording Making cable connections Installing the receiverOperating range of remote control unit Before you start Checking what’s in the boxMinute guide Introduction to home theater 02 5 minute guide Listening to Surround Sound Hook up your DVD playerHook up your TV Connect your speakers Minute guideSBL SBR 02 5 minute guidePlay a DVD, and adjust the volume to your liking 0ch 02 5 minute guide Using the Quick SetupPress Quick Setup 1chComponent video cords Connecting upAudio/Video cords Video cablesVSX-D711 Connecting up Connecting digital componentsVSX-D811S CD player Connecting up Connecting audio componentsVideo Connecting up Connecting DVD 5.1 channel componentsConnecting to the front panel video terminal Connecting up Connecting video componentsConnecting up Connecting antennas FM wire antennaAM loop antenna Connecting up Connecting the speakers VSX-D711 Connecting up Connecting the speakers VSX-D811S To 16 ΩBe sure to complete Hints on speaker placement Speaker terminalsB speaker systems View of speaker set up VSX-D811S VSX-D811S only Connecting up Connecting additional amplifiersControl OUT terminal Connecting up AC outletOperating other Pioneer components Appliance to this Units AC OutletEnter Master VolumeControls and Displays Front panel STANDBY/ONDisplay Controls and DisplaysATT AnalogDTS PRO LogicDISPLAY/DISC Enter Controls and Displays Remote controlSource RCVTOP Menu DTV InfoDTV ON/OFF DTV MenuLED Display TV Volume +Mute TV InputStandard mode Playing sources Introduction to Sound ModesStereo/Direct Analog 2-channel stereo source Playing sourcesAdvanced Surround modes Sources with stereo surroundListening to multi-channel playback Playing sources Choosing the input signalStart playback of the component you selected in step Using Stereo/DirectUsing Advanced Surround NEO6Treble Playing sources Using Loudness and Midnight listeningUsing the tone controls Playing other sourcesDVD Playing sources Selecting the multi-channel analog inputsSetting up the receiver Choosing your receiver setup FL-CS-SFL-CL-SL FL-CS-SS FL-CL-SS FL-CS-SL FL-CL-S Setting up the receiverSpeaker setting FL-C FS-CS-SCrossover frequency setting Surround back speaker settingChannel setting Subwoofer settingSurround speaker distance set- ting Center speaker distance settingLFE attenuator setting Front speaker distance settingComponent video input settings Surround back speaker distance settingDynamic range control setting Dual mono settingSB 2ch Use ’ or ‘ to select SB 2ch in or SB 1ch Surround back channel input settingCoaxial digital input settings Optical digital input settingsFL C FR SW SL SB Setting the relative volume level of each channelUse Level +/- to adjust the speaker levels in turn When you’re done, press Test Tone to turn off the test toneUsing the tuner Listening to the radio Tuning directly to a stationImproving FM stereo sound Press T.EDIT Tuner Edit Using the tunerSaving station presets Tune to a station you want to memo RizeInput the name you want Using the tuner Naming station presetsListening to station presets Choose the station preset you want to name Monitoring your recording Making Recordings Making an audio or a video recordingSelecting preset codes directly Setting the remote to control other componentsPress Remote Setup and hold for three seconds Searching for preset codesProgramming signals from other remote controls Switch on the component you want to controlPress and hold the button to be erased for three seconds Erasing one of the remote control button settingsClearing all the remote control settings Prepare the remote to erase the button settingDirect function Confirming preset codesSUB Title Controlling the rest of your system Controls for TVsChannel TV VOLControls for other components Controlling the rest of your systemDisplay MenuEnter Channel Manufacturer Code Controlling the rest of your system Preset Code List1036, 1086 1096 1055, 1086, 10891013, 1019, 1026, 1027 1032, 10631014 11141013, 1019 1017, 1032, 10891055, 1073 10591006, 1079 1132MD Player LD PlayerCD Player DVD Player Tape DeckAmplifier Misc AudioReceivers VCR 2001, 2017, 2034, 2059 2062, 2085, 2087 2015, 2027, 20322015, 2042 2017, 2018, 2053Satellite Tuner 4034 40154008 4005Cable TV Receiver Additional information TroubleshootingAdjust the Master Volume Place the antenna farther away from the equipment causingLight Additional informationFront panel refer to Remove the obstacle or operate from another positionFM Tuner Section Additional information SpecificationsAmplifier Section Video SectionFurnished Parts MiscellaneousWe Want You Listening For a Lifetime Additional information Additional information Additional information TNGZF/01L00001 Printed XRB3013-A 0 4 2 1 1 4 0
Top Page Image Contents