Pioneer VSX-D711, VSX-D811S manual Center speaker distance setting, LFE attenuator setting

Page 41

Setting up the receiver

06

150 Hz

Sends bass frequencies below 150 Hz to the subwoofer (or L speakers).

200 Hz

Sends bass frequencies below 200 Hz to the subwoofer (or L speakers).

If all speakers (front, center, and surround) are set to L, the crossover frequency can’t be set because there are no S speakers

( appears in the display).

Center speaker distance setting

Default setting: 10 ft.

The center speaker is normally placed directly in the front of the listening room and closer to the listening position than the front speakers. This means that the sound from the center speaker will be heard before the front speakers. To prevent this, set the center speaker distance setting to delay the sound from the center speaker so that the sound from the front and center speakers will be heard at the same time.

Use or to set the distance of the center speaker from the main listening position (within a 30 foot range).

LFE attenuator setting

Default setting: 0 dB

Dolby Digital and DTS audio sources include ultra-low bass tones. Set the LFE attenuator as necessary to prevent the ultra-low bass tones from distorting the sound from the speakers.

Use or to set the attenuation level

(0 dB, 10 dB or

dB()).

 

 

0 dB

 

 

10 dB

 

 

 

(displays )

When is selected ( appears in the display), LFE is not available.

Front speaker distance setting

Default setting: 10 ft.

Sets the distance from the front speakers to the listening position.

Use or to set the distance of the front speakers from the main listening position (within a 30 foot range).

When C is selected in the speaker setting, the center speaker distance can’t be set.

Surround speaker distance set- ting

Default setting: 10 ft.

Like the center speaker, you should set the distance of the surround speakers accurately to hear sounds coming from both front and surround speakers at the same time.

Use or to set the distance of the surround speakers from the main listening position (within a 30 foot range).

When S is selected in the speaker setting, the surround speaker distance can’t be set.

41

En

XRB3013A.38.44

41

01.12.12, 4:46 PM

Image 41
Contents VSX-D711 VSX-D811S Important Notice XRB3013A.01.06 01.12.12, 441 PM Contents Making a recording Operating range of remote control unit Installing the receiverBefore you start Checking what’s in the box Making cable connectionsMinute guide Introduction to home theater Hook up your TV 02 5 minute guide Listening to Surround SoundHook up your DVD player Connect your speakers Minute guideSBL SBR 02 5 minute guidePlay a DVD, and adjust the volume to your liking Press Quick Setup 02 5 minute guide Using the Quick Setup1ch 0chAudio/Video cords Connecting upVideo cables Component video cordsVSX-D711 Connecting up Connecting digital componentsVSX-D811S CD player Connecting up Connecting audio componentsVideo Connecting up Connecting DVD 5.1 channel componentsConnecting to the front panel video terminal Connecting up Connecting video componentsAM loop antenna Connecting up Connecting antennasFM wire antenna Connecting up Connecting the speakers VSX-D711 Be sure to complete Connecting up Connecting the speakers VSX-D811STo 16 Ω B speaker systems Hints on speaker placementSpeaker terminals View of speaker set up VSX-D811S VSX-D811S only Connecting up Connecting additional amplifiersOperating other Pioneer components Connecting up AC outletAppliance to this Units AC Outlet Control OUT terminalControls and Displays Front panel Master VolumeSTANDBY/ON EnterDisplay Controls and DisplaysDTS AnalogPRO Logic ATTSource Controls and Displays Remote controlRCV DISPLAY/DISC EnterDTV ON/OFF DTV InfoDTV Menu TOP MenuMute TV Volume +TV Input LED DisplayStereo/Direct Standard modePlaying sources Introduction to Sound Modes Advanced Surround modes Playing sourcesSources with stereo surround Analog 2-channel stereo sourceListening to multi-channel playback Playing sources Choosing the input signalUsing Advanced Surround Using Stereo/DirectNEO6 Start playback of the component you selected in stepUsing the tone controls Playing sources Using Loudness and Midnight listeningPlaying other sources TrebleDVD Playing sources Selecting the multi-channel analog inputsSetting up the receiver Choosing your receiver setup Speaker setting Setting up the receiverFL-C FS-CS-S FL-CS-SFL-CL-SL FL-CS-SS FL-CL-SS FL-CS-SL FL-CL-SChannel setting Surround back speaker settingSubwoofer setting Crossover frequency settingLFE attenuator setting Center speaker distance settingFront speaker distance setting Surround speaker distance set- tingDynamic range control setting Surround back speaker distance settingDual mono setting Component video input settingsCoaxial digital input settings Surround back channel input settingOptical digital input settings SB 2ch Use ’ or ‘ to select SB 2ch in or SB 1chUse Level +/- to adjust the speaker levels in turn Setting the relative volume level of each channelWhen you’re done, press Test Tone to turn off the test tone FL C FR SW SL SBImproving FM stereo sound Using the tuner Listening to the radioTuning directly to a station Saving station presets Using the tunerTune to a station you want to memo Rize Press T.EDIT Tuner EditListening to station presets Using the tuner Naming station presetsChoose the station preset you want to name Input the name you wantMonitoring your recording Making Recordings Making an audio or a video recordingSelecting preset codes directly Setting the remote to control other componentsProgramming signals from other remote controls Searching for preset codesSwitch on the component you want to control Press Remote Setup and hold for three secondsClearing all the remote control settings Erasing one of the remote control button settingsPrepare the remote to erase the button setting Press and hold the button to be erased for three secondsDirect function Confirming preset codesChannel Controlling the rest of your system Controls for TVsTV VOL SUB TitleControls for other components Controlling the rest of your systemEnter Channel DisplayMenu Manufacturer Code Controlling the rest of your system Preset Code List1013, 1019, 1026, 1027 1055, 1086, 10891032, 1063 1036, 1086 10961013, 1019 11141017, 1032, 1089 10141006, 1079 10591132 1055, 1073CD Player MD PlayerLD Player DVD Player Tape DeckReceivers AmplifierMisc Audio VCR 2015, 2042 2015, 2027, 20322017, 2018, 2053 2001, 2017, 2034, 2059 2062, 2085, 2087Satellite Tuner 4008 40154005 4034Cable TV Adjust the Master Volume Additional information TroubleshootingPlace the antenna farther away from the equipment causing ReceiverFront panel refer to Additional informationRemove the obstacle or operate from another position LightAmplifier Section Additional information SpecificationsVideo Section FM Tuner SectionFurnished Parts MiscellaneousWe Want You Listening For a Lifetime Additional information Additional information Additional information TNGZF/01L00001 Printed XRB3013-A 0 4 2 1 1 4 0