Panasonic TH-C50FD18 quick start Side Bar, Scrolling bar, Input signal that can be displayed

Side Bar

Do not display a picture in 4:3 mode for an extended period, as this can cause							Side Bar			Image retention
“Image retention” to remain on either or both sides of the display field.
To reduce the risk of such “Image retention”, change the brightness of the side							4:3
bars.							Screen
See pages 26-27 for more information							Display
	The side bar may flash (alternate black/white) depending on the picture. Using
	Cinema mode will reduce such flashing (See below).
					Scrolling bar
Scrolling bar: To prevent “Image retention”, scrolls white vertical bar from left to right on a black screen.										[Scrolling bar]
	Press any key except the POWER key to return to previous screen.
	You will return to previous screen if no key operation has not been performed for 15 minutes.
	See pages 26-27 for more information
					Input signal that can be displayed
* Mark: Applicable input signal for Component (Y, PB, PR), HDMI and PC
				horizontal frequency (kHz)		vertical frequency (Hz)		COMPONENT	HDMI		PC
525		(480) / 60i			15.73	59.94		*	*
	525	(480) /60p			31.47	59.94		*	*
	750	(720) /60p			45.00	59.94		*	*
	1,125		(1,080) /60i		33.75	59.94		*	*
	1,125		(1,080) /60p		67.43	59.94			*
	1,125		(1,080) /60p		67.50	60.00			*
	1,125		(1,080) /24p		26.97	23.98			*
	1,125		(1,080) /24p		27.00	24.00			*
	640	× 400 @70			31.47	70.08					*
	640	× 480 @60			31.47	59.94					*
	Macintosh13” (640 × 480)				35.00	66.67					*
	640	× 480 @75			37.50	75.00					*
	852	× 480 @60			31.47	59.94					*
	800	× 600 @60			37.88	60.32					*
	800	× 600 @75			46.88	75.00					*
	800	× 600 @85			53.67	85.08					*
	Macintosh16” (832 × 624)				49.73	74.55					*
	1,024		× 768 @60		48.36	60.00					*
	1,024		× 768 @70		56.48	70.07					*
	1,024		× 768 @75		60.02	75.03					*
	1,024		× 768 @85		68.68	85.00					*
	Macintosh 21” (1,152 × 870)				68.68	75.06					*
	1,280		× 1,024 @60		63.98	60.02					*
	1,366		× 768 @60		48.36	60.00					*

Note

Signals other than above may not be displayed properly.

The above signals are reformatted for optimal viewing on your display.

PC Input Terminals Connection

Computer signals which can be input are those with a horizontal scanning frequency of 15 to 110 kHz and vertical scanning frequency of 48 to 120 Hz. (However, the image will not be displayed properly if the signals exceed 1,200 lines.)

Some PC models cannot be connected to the set.

There is no need to use an adapter for computers with IBM PC/AT compatible D-sub 15P terminal.

The maximum resolution: 1,280 × 1,024

If the display resolution exceeds these maximums, it may not be possible to show fine detail with sufficient clarity. Signal Names for D-sub 15P Connector

				Pin No.	Signal Name	Pin No.	Signal Name	Pin No.	Signal Name
11	12	13	14	15	R		GND (Ground)		NC (not connected)
6	7	8	9 10		G		GND (Ground)		NC
1	2	3	4	5	B		GND (Ground)		HD/SYNC
					NC (not connected)		NC (not connected)		VD
Pin Layout for PC Input Terminal					GND (Ground)		GND (Ground)		NC

Technical Information FAQs, etc.

45