Network settings
These settings are used if you will connect this unit to the Internet.
≥The connection to the Internet may take time or the Internet may not be connected depending on the connection environment. (> 28) It is required that you use a broadband connection.
Preparation
≥Connect to the network. (> 9)
Testing the connection
Always test the connection when a LAN cable is connected or when new “IP Address/DNS Settings” have been made.
1Press [SETUP].
2Press [3, 4] to select “Network” and press [OK].
3Press [3, 4] to select “IP Address/DNS Settings” and press [OK].
4Press [3, 4] to select “Connection Test” and press [OK].
IP Address/DNS Settings |
|
Connection Test | |
IP Address Auto Configuration (DHCP) | On |
IP Address | 㪄 㪄 㪄 㪅 㩷 㪄 㪄 㪄 㪅 㩷 㪄 㪄 㪄 㪅 㩷 㪄 㪄 㪄 㩷 |
Subnet Mask | 㪄 㪄 㪄 㪅 㩷 㪄 㪄 㪄 㪅 㩷 㪄 㪄 㪄 㪅 㩷 㪄 㪄 㪄 㩷 |
Default Gateway | 㪄 㪄 㪄 㪅 㩷 㪄 㪄 㪄 㪅 㩷 㪄 㪄 㪄 㪅 㩷 㪄 㪄 㪄 㩷 |
DNS Auto Configuration (DHCP) | On |
Primary DNS | 㪄 㪄 㪄 㪅 㩷 㪄 㪄 㪄 㪅 㩷 㪄 㪄 㪄 㪅 㩷 㪄 㪄 㪄 㩷 |
Secondary DNS | 㪄 㪄 㪄 㪅 㩷 㪄 㪄 㪄 㪅 㩷 㪄 㪄 㪄 㪅 㩷 㪄 㪄 㪄 㩷 |
Auto Detect Connection Speed | On |
Connection Speed Setting | |
OK |
|
RETURN |
|
“Testing”: | The test is in progress. |
“Pass”: | The connection is completed. |
“Fail”: | Please check the connection and settings. |
≥If the connection test fails, it may be necessary to change your router’s MAC address settings.The MAC address can be displayed by pressing [SETUP] and selecting “Network”.
Network
IP Address/DNS Settings
Proxy Server Settings
MAC Address:
OK
RETURN
Setting the IP address
In most cases, default settings can normally be used without making any changes.
Set the IP address only when the router has no DHCP server functions or when the router’s DHCP server function is disabled.
After performing steps
4Press [3, 4] to select “IP Address Auto Configuration (DHCP)” and press [2, 1] to select “Off”.
5Press [3, 4] to select “IP Address”, “Subnet Mask” or “Default Gateway” and press [OK].
6Enter numbers with the numbered buttons and press [OK].
≥After checking the specifications for your broadband router, enter each number.
If the number is unknown, then check the number of other devices such as personal computers connected via a LAN cable. Assign a different number from those of other devices for the “IP Address” and the same number for others.
≥If a wrong number is entered, then press [CANCEL].
[Note]
RQT9184 ≥The numeric input range is between 0 and 255. (ENG)
Setting the DNS-IP
In most cases, default settings can normally be used without making any changes.
When setting an assigned DNS server from your Internet service provider, perform the following settings.
After performing steps
4Press [3, 4] to select “DNS Auto
Configuration (DHCP)” and press [2, 1] to select “Off”.
5Press [3, 4] to select “Primary DNS” or “Secondary DNS”and press [OK].
6Enter numbers with the numbered buttons and press [OK].
≥Follow the instructions given by your Internet service provider and enter the numbers.
If the number is unknown, then check the number of other devices such as personal computers connected via a LAN
cable and assign the same number.
≥If a wrong number is entered, then press [CANCEL].
Primary DNS
Please input Primary DNS and press
[OK]. Press [CANCEL] to delete the selected character. To clear setting, delete all characters, then press [OK].
192 | . |
| 1 |
| . |
| . | ||
|
|
|
|
|
|
|
|
|
|
|
| - 9 |
| Number |
|
|
| ||
0 |
|
|
|
| |||||
[Note]
≥The numeric input range is between 0 and 255.
Setting the connection speed
When the connection test results in “Fail” after the IP and
After performing steps
4Press [3, 4] to select “Auto Detect
Connection Speed” and press [2, 1] to select “Off”.
5Press [3, 4] to select “Connection Speed Setting” and press [2, 1] to select a
connection speed.
≥Select a connection speed in accordance with the environment
of the network connected.
≥When the settings are changed, the network connection may be disabled depending on the device.
12