Panasonic DMP-BD50 warranty Messages, On the television, On the unit’s display

Messages

The following messages or service numbers appear on the television or unit’s display when something unusual is detected during startup and

use.
On the television		Page
Authorization Error	≥You are trying to play the DivX VOD content that was purchased with a different	20
This unit is not authorized to	registration code. You cannot play the content on this unit.
play this title.
Cannot play.	≥You inserted an incompatible disc (Discs recorded in PAL video, etc.).	4, 5
Cannot display on this unit.	≥You tried to play a non-compatible image.	5, 22
	≥Confirm “SD” on the unit’s display is not blinking and re-insert the card.	—
No disc is inserted.	≥The disc may be upside down.	—
Rental Expired.	≥The DivX VOD content has zero remaining plays. You cannot play it.	20
$ This operation is currently	≥The operation is prohibited by the unit or disc.	—
disabled.
Cannot connect.	≥When a hub is used but its Link lamp does not light up, check the cable connection, LAN
Please check the connection of	terminal connection, cable itself (a cross cable may be used by mistake), etc.	9
the LAN cable.
IP address is not set.	≥The “IP Address” in “IP Address/DNS Settings” is “---. ---. ---. ---“. Set the “IP Address”,	12
	“Subnet Mask”, and “Default Gateway“. (Select the automatic address acquisition if
	necessary.)
Cannot obtain IP address using	≥If you use a hub, then check the connection between the hub and the router.
DHCP.	– Use the UPLINK port of the hub to connect to a router.
Please check the connection or	– Check whether or not the hub’s Link lamp lights up. If it does not light up, then check the	9
router settings.	cable connection, LAN terminal connection, cable itself (a cross cable may be used by
	mistake), etc.
	≥If the above conditions are OK, then the router may not operate in DHCP mode. Check the
	router settings and operation. You may reset the router to restore it to normal.
This IP address is already in	≥This unit’s IP address is used by another device. Check the IP addresses of this unit,
use.	personal computers, and routers, etc. If necessary, reconfigure them to avoid IP addresses	—
Please check the IP address	from being duplicated.
setting.
Unable to perform Connection	≥Turn the unit off. Remove the power cord and reconnect it and try again. If the same
Test.	symptom persists, then consult your dealer.	—
Please try again.
IP address not set correctly.
Connection Test was	≥If you use a hub, then check the connection between the hub and the router.	9
unsuccessful. No reply	– Use the UPLINK port of the hub to connect to a router.
from host.	– If the hub’s Link lamp does not light up, then check the cable connection, LAN terminal
Please check the connection or	connection, cable itself (a cross cable may be used by mistake), etc.	12
router settings.	≥Check the “IP Address”, “Subnet Mask”, and “Default Gateway” in the “IP Address/DNS
	Settings”.	12
	≥If the MAC address information is required, then press [SETUP] to display the “Network”
	menu.
Network connection refused.	≥When you set “BD-Live Internet Access” to “Allow (Limited)” and play BD-Live contents
Please confirm Setup “BD-Live	which do not have a content owner certificate, the Internet access of the content is not	26
Internet Access”	allowed. If you allow the content to connect to Internet, set “BD-Live Internet Access” to
	“Allow (ALL)”.

RQT9184

(ENG)

On the unit’s display

F99	≥The unit fails to operate properly. Press [POWER Í/I] on the main unit to switch the unit to			—
		standby for 3 seconds. Now press [POWER Í/I] on the main unit again to turn the unit on.
HDMI ONLY	≥Some BD-Video discs can only be output with HDMI.			—
No PLAY	≥There is a viewing restriction on a BD-Video or DVD-Video.			26
No READ	≥The disc is dirty or badly scratched. The unit cannot play.			—
PLEASE WAIT	≥Displayed when the unit is started and turned off. This is not a malfunction.			—
	≥The unit is carrying out its recovery process. You cannot operate the unit while “PLEASE			—
		WAIT” is displayed.
SET 	≥The remote control and main unit are using different codes. Change the code on the			33
(“  ” stands for a number.)		remote control.
			Press and hold [OK] and the indicated number button at the same
			time for more than 5 seconds.
UNFORMAT	≥You inserted an unformatted DVD-RAM, DVD-RW, +RW, an unused +R, +R DL or			—
		DVD-RW (DVD-Video format).
UNSUPPORT	≥You have inserted a disc the unit cannot play.			4, 5
U59	≥The unit is hot.			—
		The unit switches to standby for safety reasons. Wait for about 30 minutes until the
		message disappears.
		Select a position with good ventilation when installing the unit. Do not block the cooling fan
		on the rear of the unit.
U72	≥The HDMI connection acts unusually.			—
U73		– The connected equipment is not HDMI compatible.
		– Please use HDMI cables that have the HDMI logo (as shown on the cover).
		– The HDMI cable is damaged.

34