Panasonic DMP-BD50 warranty Sound, Hdmi connections

TV screen and video (continued)		Page
The 4:3 aspect ratio picture	≥Use the television to change the aspect. Refer to your television’s operating instructions.	—
expands left and right.	≥When using a component video cable, set “Progressive” to “Video”. If the situation is not	25, 28
Screen size is wrong.	restored after that, set “TV Aspect” to “4:3 Pan & Scan”.
There is a lot of after-image	≥Turn “3D NR” or “Integrated NR” off if it is on.	25
when playing video.
There is no apparent change in	≥The effect is less perceivable with some types of video.	—
picture quality when adjusted
with the “Video” menu in the
on-screen menu.
The masked-off area is masked	≥If the “Screen Saver Function” in the Setup menu is set to “Off”, the masked-off area is	27
in gray.	displayed in black.
Sound
No sound.	≥Check the connections and the “Digital Audio Output” settings. Check the input mode on the	6–7, 27
Low volume.	amplifier/receiver if you have connected one.	15
Distorted sound.	≥Press [AUDIO] to select the audio.
Cannot hear the desired audio	≥Turn off “V. Surround” in the following cases.	25
type.	– When using discs that do not have surround sound effects such as Karaoke discs.
	– When playing bilingual broadcast programs.	28
	≥Match the speaker settings with the connected equipment. Change multi channel speaker
	settings by selecting “Multi Channel” in “Speaker”.	—
	≥The sound effects (Re-master, V. Surround, etc.) will not work when the bitstream signal is
	output from the HDMI AV OUT terminal or the DIGITAL AUDIO OUT terminal.	17, 27
	≥When “BD-Video Secondary Audio” is set to “Off”, Dolby Digital Plus, Dolby TrueHD and
	DTS-HD are output from the DIGITAL AUDIO OUT terminal as Dolby Digital or DTS Digital
	Surround bitstream.	—
	≥[DivX] Audio may not be output depending on how files were created.
Cannot switch audio.	≥There are discs for which audio cannot be changed because of how the disc was created.	—
	≥When connecting an amplifier/receiver using a coaxial cable, optical digital audio cable or an	7, 8, 27
	HDMI cable, you cannot switch the audio if “Digital Audio Output” is set to “Bitstream”. Set
	“Digital Audio Output” to “PCM” or connect using audio cables.
HDMI connections
The images from this unit do	≥Press [∫] and [1] (PLAY) simultaneously on the unit for more than 5 seconds to shift to more	29
not appear on the television.	compatible mode with HDMI equipment. However, Dolby Digital Plus, Dolby TrueHD, and
	DTS-HD audio are not output in bitstream. To output the bitstream, select “Restore Default
Picture is distorted.	Settings” to restore the factory presets and make proper settings.	28
	≥To output video from a device connected with an HDMI cable, set “HDMI Video Mode” to “On”
Jittering occurs.	in the Setup menu.	—
	≥Picture may not be seen when more than 4 devices are connected with HDMI cables.
	Reduce the number of connected devices.	28
	≥When “24p Output” is set to “On”, HDMI authentication takes place where 24p images switch
	to other images, and a black screen is displayed.	28
	≥When “24p Output” is set to “On”, jittering may occur while playing DVD-Video. In this case,
	turn “24p Output” to “Off”.
The 4:3 aspect ratio picture	≥Change “TV Aspect” type to “16:9”.	28
expands left and right.
Screen size is wrong.
When playing DVD-Video using	≥When you use the HDMI AV OUT terminal for video output, follow the steps below for setting.	28
progressive output, one part of	1 Connect this unit to the TV with any cable except the HDMI cable.
the picture momentarily	2 When you connect with the Component Video cable, set “HDMI Video Mode” to “Off” and
appears to be doubled up.	“Component Video Resolution” to “480i” in the Setup menu.
No sound.	≥Audio may not be heard when more than 4 devices are connected with HDMI cables.	—
Low volume.	Reduce the number of connected devices.	—
Distorted sound.	≥The sound effects will not work when the bitstream signal is output from the HDMI AV OUT
Cannot hear the desired audio	terminal or the DIGITAL AUDIO OUT terminal.	28
type.	≥To output audio from a device connected with an HDMI cable, set “HDMI Audio Output” to
	“On” in the Setup menu.	28
	≥If the sound is distorted when the unit is connected to an amplifier/receiver with an HDMI
	cable, adjust the settings in “Speaker” in the Setup menu to match the connection.	—
	≥Depending on the connected equipment, the sound may be distorted if this unit is connected
	with an HDMI cable.	27
	≥When “BD-Video Secondary Audio” is set to “On”, Dolby Digital Plus, Dolby TrueHD, and
	DTS-HD are converted to 48 kHz Dolby Digital and output. LPCM 7.1 channel audio is
	converted to 5.1 channel audio. In this case, set the “BD-Video Secondary Audio” to “Off”.

RQT9184

(ENG)

32