Panasonic TH-42PG9W Initial selections, Selecting the input signal, Swing up the door at Pull

Page 13

Initial selections

Selecting the input signal

Select the input signals to be connected by installing the optional Terminal Boards.

Press to select the input signal to be played back from the equipment which has been connected to the Plasma Display.

Input signals will change as follow:

INPUT1 INPUT2 INPUT3 PC IN

Notes:

•Selecting is also possible by pressing the INPUT button on the unit.

•Input terminal will not be selected if the terminal board is not installed into the SLOT.

•Select to match the signals from the source connected to the component/RGB input terminals. (see page 32)

•In 2 screen display, the same input mode cannot be selected for the main picture and sub picture.

INPUT MENU VOL ENTER/

Swing up the door at “PULL”.

Selecting the On-Screen Menu Language

Press to display the Setup menu.

Press to select the OSD Language.

Press to select your preferred language.

Selectable languages

English(UK)

Deutsch

Français

Italiano

Español

ENGLISH(US)

.......(Chinese)

.......(Japanese)

Русский .......(Russian)


		Setup			1/2


		Signal

		Component/RGB-in select
						RGB

		Input label				PC

		Power save				Off

		Standby save				Off

		Power management				Off

		Auto power off				Off

		OSD Language			English (UK)

13

Image 13

Contents English Operating InstructionsModel No. TH-37PG9W Table of Contents Trademark Credits Important Safety NoticeSetup Safety PrecautionsDo not place any objects on top of the Plasma Display If problems occur during use When using the Plasma DisplayElectric shocks can result if this is not done Clean the power cable regularly to prevent it becoming dustyAccessories Supply AccessoriesCheck that you have the accessories and items shown AC cord fixing ConnectionsAC cord connection see PC Input Terminals connection Signal Names for Mini D-sub 15P ConnectorSerial Terminals connection CommandRS-232C Straight cable Communication parametersExample of input signal source RGB signal R, G, BComponent / RGB in connection Digital TV Set-Top-BoxConnecting the AC cord plug to the Plasma Display Power On / OffConnecting the plug to the Wall Outlet Initial selections Selecting the input signalSelecting the On-Screen Menu Language Swing up the door at PullBasic Controls OFF Timer button Channel AdjustmentDigital Zoom see Press to access Standby on / OFF buttonOn-Screen Menu Displays To Signal screen for Digital see page 33 Press to access From the unit Each adjust ScreenTo Set up Timer selection screen see page 26 To Present Time Setup seeAspect Controls Mode Picture ExplanationNormalisation Adjusting Pos. / SizePress to swap main picture and sub picture Is pressed except button Press to change input signalSub screen Main screen Advanced PIPNormal Picture AdjustmentsDynamic CinemaAdvanced settings Mute Sound AdjustmentDisplay the Operation Guide Digital ZoomSelect the area of the image to be enlarged Select the magnification required for the enlarged displayPresent Time Setup Present Time Setup / Set up TimerDisplay the Set up Timer screen Press to select Set up TimerPower on Time / Power OFF Time Press to setupStart setting Mode selectionScreensaver For preventing after-images Reversal / Scroll selectionReduces screen after-image Setup of Screensaver TimeThis function may be applicable to the non-picture area Side Panel AdjustmentAddition sign Selected Input Reduces power consumptionComposite PB, PR signals Component B, HD, VD signals Setup for Input SignalsComponent / RGB-in select 3D Y/C Filter For Ntsc AV imagesCinema reality / P-NR Colour system / Panasonic AutoSync Setting RGB sync signalFreq. kHz / V-Freq. Hz Displays the H Horizontal / V Vertical frequenciesEffect Adjustments Options AdjustmentsOptions Adjustments Menu & Enter NormalizationShipping condition Plasma Display panel TroubleshootingHorizontal Vertical Component COMPONENT/RGB/PC input signalsFrequency kHz Frequency Hz Component TH-37PG9W TH-42PG9W SpecificationsMemo Memo Customer’s Record