Panasonic TH-37PG9W, TH-42PG9W manual Connections, AC cord fixing, AC cord connection see

Page 8

Connections

– AC cord fixing

AC cord connection (see page 12)

1

Connect power plug to

How to fix:

How to release:

the socket of the main

Fix by pushing in until a

Pull up while drawing in

body.

1

clicking sound is heard.

the knob.

2

Fix the clamper.

2

– Cable fixing bands Secure any excess cables with bands as required.

Pass the attached cable fixing band through the clip as shown in the figure.

To secure cables connected to Terminals, wrap the cable fixing band around them then pass the pointed end through the locking block, as shown in the figure.

While ensuring there is sufficient slack in cables to minimize stress (especially in the power cord), firmly bind all cables with the supplied fixing band.

1

	To tighten:		To loosen:
			Push the catch
	Pull
	2		Pull
R AUDIO L PR/CR/R PB/CB/B	Y/G		AUDIO
COMPONENT/RGB IN	SLOT 1 2 3		AUDIO
COMPONENT/RGB IN	SLOT 1 2 3
SLOT1	SLOT2	SLOT3	PC IN	SERIAL
SLOT1	SLOT2	SLOT3

COMPONENT/RGB IN and Audio IN Terminals (see page 11)

Optional Terminal Board Insert Slot (covered)

From EXTERNAL monitor terminal on Computer (see page 9)

From SERIAL Terminal on Computer

(see page 10)

Note:

At factory shipment, Terminal board is installed in SLOT 1 only.

8

Image 8

Contents Model No. TH-37PG9W Operating InstructionsEnglish Table of Contents Important Safety Notice Trademark CreditsDo not place any objects on top of the Plasma Display Safety PrecautionsSetup When using the Plasma Display If problems occur during useClean the power cable regularly to prevent it becoming dusty Electric shocks can result if this is not doneCheck that you have the accessories and items shown AccessoriesAccessories Supply AC cord connection see ConnectionsAC cord fixing Signal Names for Mini D-sub 15P Connector PC Input Terminals connectionCommand Serial Terminals connectionRS-232C Straight cable Communication parametersRGB signal R, G, B Example of input signal sourceComponent / RGB in connection Digital TV Set-Top-BoxConnecting the plug to the Wall Outlet Power On / OffConnecting the AC cord plug to the Plasma Display Selecting the input signal Initial selectionsSelecting the On-Screen Menu Language Swing up the door at PullBasic Controls Channel Adjustment OFF Timer buttonDigital Zoom see Press to access Standby on / OFF buttonOn-Screen Menu Displays Press to access From the unit Each adjust Screen To Signal screen for Digital see page 33To Set up Timer selection screen see page 26 To Present Time Setup seeMode Picture Explanation Aspect ControlsAdjusting Pos. / Size NormalisationIs pressed except button Press to change input signal Press to swap main picture and sub pictureAdvanced PIP Sub screen Main screenPicture Adjustments NormalDynamic CinemaAdvanced settings Sound Adjustment MuteDigital Zoom Display the Operation GuideSelect the area of the image to be enlarged Select the magnification required for the enlarged displayPresent Time Setup / Set up Timer Present Time SetupSet up Timer Display the Set up Timer screen Press to selectPower on Time / Power OFF Time Press to setupMode selection Start settingScreensaver For preventing after-images Reversal / Scroll selectionSetup of Screensaver Time Reduces screen after-imageSide Panel Adjustment This function may be applicable to the non-picture areaComposite Reduces power consumptionAddition sign Selected Input Setup for Input Signals PB, PR signals Component B, HD, VD signalsComponent / RGB-in select 3D Y/C Filter For Ntsc AV imagesColour system / Panasonic Auto Cinema reality / P-NRSetting RGB sync signal SyncFreq. kHz / V-Freq. Hz Displays the H Horizontal / V Vertical frequenciesOptions Adjustments Effect AdjustmentsOptions Adjustments Normalization Menu & EnterShipping condition Troubleshooting Plasma Display panelFrequency kHz Frequency Hz Component COMPONENT/RGB/PC input signalsHorizontal Vertical Component Specifications TH-37PG9W TH-42PG9WMemo Memo Customer’s Record