Panasonic TH-42PG9W PC Input Terminals connection, Signal Names for Mini D-sub 15P Connector

Page 9

Connections

PC Input Terminals connection

COMPUTER

Conversion adapter (if necessary)

AUDIO

PC IN

Mini D-sub 15p

RGB

PC cable

Audio

Stereo plug

 

Connect a cable which matches

the audio output terminal on the computer.

Notes:

Due to space limitations, occasionally you may have trouble connecting Mini D-sub 15P cable with ferrite core to PC input Terminal.

Computer signals which can be input are those with a horizontal scanning frequency of 15 to 110 kHz and vertical scanning frequency of 48 to 120 Hz. (However, the image will not be displayed properly if the signals exceed 1,200 lines.)

The display resolution is a maximum of 640 × 480 dots (TH-37PG9W, TH-42PG9W) when the aspect mode is set to “4:3”, and 852 × 480 dots (TH-37PG9W, TH-42PG9W) when the aspect mode is set to “16:9”. If the display resolution exceeds these maximums, it may not be possible to show fine detail with sufficient clarity.

The PC input terminals are DDC1/2B-compatible. If the computer being connected is not DDC1/2B-compatible, you will need to make setting changes to the computer at the time of connection.

Some PC models cannot be connected to the set.

There is no need to use an adapter for computers with DOS/V compatible Mini D-sub 15P terminal.

The computer shown in the illustration is for example purposes only.

Additional equipment and cables shown are not supplied with this set.

Do not set the horizontal and vertical scanning frequencies for PC signals which are above or below the specified frequency range.

Signal Names for Mini D-sub 15P Connector

11 12 13 14 15

6 7 8 9 10

1 2 3 4 5

Pin Layout for PC Input Terminal

Pin No.

Signal Name

Pin No.

Signal Name

Pin No.

Signal Name

1

R (PR/CR)

6

GND (Ground)

11

NC (not connected)

2

G (Y)

7

GND (Ground)

12

SDA

3

B (PB/CB)

8

GND (Ground)

13

HD/SYNC

4

NC (not connected)

9

NC (not connected)

14

VD

5

GND (Ground)

10

GND (Ground)

15

SCL

9

Image 9
Contents Operating Instructions EnglishModel No. TH-37PG9W Table of Contents Trademark Credits Important Safety NoticeSafety Precautions SetupDo not place any objects on top of the Plasma Display If problems occur during use When using the Plasma DisplayElectric shocks can result if this is not done Clean the power cable regularly to prevent it becoming dustyAccessories Accessories SupplyCheck that you have the accessories and items shown Connections AC cord fixingAC cord connection see PC Input Terminals connection Signal Names for Mini D-sub 15P ConnectorSerial Terminals connection CommandRS-232C Straight cable Communication parametersExample of input signal source RGB signal R, G, BComponent / RGB in connection Digital TV Set-Top-BoxPower On / Off Connecting the AC cord plug to the Plasma DisplayConnecting the plug to the Wall Outlet Initial selections Selecting the input signalSelecting the On-Screen Menu Language Swing up the door at PullBasic Controls OFF Timer button Channel AdjustmentDigital Zoom see Press to access Standby on / OFF buttonOn-Screen Menu Displays To Signal screen for Digital see page 33 Press to access From the unit Each adjust ScreenTo Set up Timer selection screen see page 26 To Present Time Setup seeAspect Controls Mode Picture ExplanationNormalisation Adjusting Pos. / SizePress to swap main picture and sub picture Is pressed except button Press to change input signalSub screen Main screen Advanced PIPNormal Picture AdjustmentsDynamic CinemaAdvanced settings Mute Sound AdjustmentDisplay the Operation Guide Digital ZoomSelect the area of the image to be enlarged Select the magnification required for the enlarged displayPresent Time Setup Present Time Setup / Set up TimerDisplay the Set up Timer screen Press to select Set up TimerPower on Time / Power OFF Time Press to setupStart setting Mode selectionScreensaver For preventing after-images Reversal / Scroll selectionReduces screen after-image Setup of Screensaver TimeThis function may be applicable to the non-picture area Side Panel AdjustmentReduces power consumption Addition sign Selected InputComposite PB, PR signals Component B, HD, VD signals Setup for Input SignalsComponent / RGB-in select 3D Y/C Filter For Ntsc AV imagesCinema reality / P-NR Colour system / Panasonic AutoSync Setting RGB sync signalFreq. kHz / V-Freq. Hz Displays the H Horizontal / V Vertical frequenciesEffect Adjustments Options AdjustmentsOptions Adjustments Menu & Enter NormalizationShipping condition Plasma Display panel TroubleshootingCOMPONENT/RGB/PC input signals Horizontal Vertical ComponentFrequency kHz Frequency Hz Component TH-37PG9W TH-42PG9W SpecificationsMemo Memo Customer’s Record