Sony HT-4850DP, HT-5800DP Listening to FM/AM radio, Automatic tuning, Amplifier Operation 19US

Page 19

The last received station is tuned in.

Tip

You can also use TUNER FM/AM on the receiver.

2 Press D.TUNING.

3 Press the numeric buttons to enter the frequency.

Example 1: FM 102.50 MHz Press 1 b 0 b 2 b 5 b 0 Example 2: AM 1,350 kHz

(You do not have to enter the last “0” when the tuning scale is set to 10 kHz.)

Press 1 b 3 b 5 b 0

If you have tuned in an AM station, adjust the direction of the AM loop antenna for optimum reception.

If you cannot tune in a station and the entered numbers flash

Make sure you have entered the right frequency. If not, repeat steps 2 and 3. If the entered numbers still flash, the frequency is not used in your area.

Press TUNER repeatedly to select the FM or AM band.

1

Direct tuning

You can enter the frequency of the station you want directly. Use the remote for the operation.

Listening to FM/AM radio

You can listen to FM and AM broadcasts through the built-in tuner. Before operation, make sure you have connected the FM and AM antennas to the receiver (see page 11).

Tip

The tuning scale differs depending on the area code as shown in the following table. For details on area codes, see page 3.

Area code	FM	AM
U, CA	100 kHz	10 kHz*

* The AM tuning scale can be changed (see page 43).

Automatic tuning

If you do not know the frequency of the station you want, you can let the receiver scan all available stations in your area.

1 Press TUNER FM/AM repeatedly to select the FM or AM band.

The last received station is tuned in.

2 Press TUNING + or TUNING –.

Press TUNING + to scan from low to high; press TUNING – to scan from high to low. The receiver stops scanning whenever a station is received.

Tip

If “STEREO” flashes in the display and the FM stereo reception is poor, press FM MODE to change to monaural (MONO). You will not be able to enjoy the stereo effect, but the sound will be less distorted. To return to stereo mode, press FM MODE again.

Amplifier Operation

19US

Image 19

Contents Home Theatre System For customers in the United States SS-MSP68 SS-CNP68 SA-WMSP68 DVP-NC675P About This ManualSS-MSP68 SS-CNP68 SA-WMSP76 DVP-NC675P Table of Contents VCR Check how to hookup your componentsConnectable components Getting StartedAudio/video cord Required cordsAudio cord Video cord Optical digital cordConnect the audio jacks Hooking up a DVD player or satellite tunerFor details on the required cords A-E, see Satellite tuner TV monitor Connect the video jacksHooking up audio components 1b Connecting components with only analog audio jacks10US Hooking up video componentsStarted Connecting the antennasConnect the supplied AM loop antenna and FM wire antenna Getting12US Connecting speakersExample of 5.1 channel speaker system configuration Attaching foot padsMonaural audio cord supplied Required cords13US Speaker cords suppliedPress Enter Connecting the AC power cordPerforming initial setup operations 14USGetting Started 15US Speaker setup parameters16US Setting up the sub wooferSL SR PL Surround speaker placement Listening to the sub wooferGetting Started 17US Adjusting the levelTurn Level to adjust the volume Press Test Tone again after adjustmentTo mute the sound When Multi Channel Decoding indicator lights upTo use the headphones Selecting the componentAmplifier Operation 19US Automatic tuningPress Tuning + or Tuning Listening to FM/AM radioPresetting radio stations Presetting radio stationsTuning to preset stations Amplifier Operation 21US Adjusting the brightness of the displayChanging the display Changing the information in the displayAbout the indications in the display DTS Lights up when DTS signals are input22US Press 2CH Decoding the input audio signal automaticallyEnjoying higher fidelity sound Enjoying Surround Sound 23US24US Selecting a sound fieldSelecting a sound field for movies About DCS Digital Cinema SoundEnjoying Surround Sound 25US Selecting a sound field for musicAbout Cinema Studio EX modes To turn off the surround effectAdjusting the Level menu Switching the audio input mode for digital componentsCustomizing sound fields EFCT. XXX Effect level Resetting sound fields to the initial settingsAdvanced Adjustments and Settings 27US Range COMP. XXX Dynamic range compressorAdvanced settings Adjusting the toneUsing the Customize menu to adjust the receiver Name Naming preset stations and inputs Advanced Adjustments and Settings 29USDual Digital broadcast language selection To index an input Naming preset stations and inputsUsing the Sleep Timer To index a preset stationOther Operations 31US RecordingRecording on an audio tape or MiniDisc Recording on a video tapeInserting batteries into the remote Before you use your remote32US Operations Using the Remote RM-PP760 33US 34US Operations Using the Remote RM-PP760 35US Selecting the command modeTo check the command mode of the remote To reset the remote to factory settingsProgramming the remote To control a tape deck To control a CD playerTo control a DAT deck To control an MD deckTo control a satellite tuner or cable box To control a VCRTo control a DVD player To control a TVAdditional Information 39US Precautions40US TroubleshootingIf there is a malfunction, the display shows a message Remote controlError message Additional Information 41US42US SpecificationsIf the problem persist Reference sections for clearing the receiver’s memory43US SA-WMSP76 Supplied accessories44US SA-WMSP68Page 46US How to use pages 46List of button locations and reference pages Main unitAdditional Information 47US Index