Sony HT-5800DP Selecting the component, When Multi Channel Decoding indicator lights up, 18US

Page 18

Amplifier Operation

Selecting the component

1 Press input buttons to select the input.

To select the	Press
VCR	VIDEO 1
	or VIDEO 2

Satellite tuner	VIDEO 2

DVD player	DVD

MD or tape deck	MD/TAPE

CD player	CD

Built-in tuner (FM/AM)	TUNER FM/AM

The selected input appears in the display.

2 Turn on the component and start playback.

Note

If you select the VCR or DVD player, set the TV’s video input to match the component you selected.

3 Turn MASTER VOLUME –/+ to adjust the volume.

Note

To avoid damaging your speakers, make sure that you turn down the volume before you turn off the receiver.

To mute the sound

Press MUTING on the remote.

The muting function will be canceled when you do the following.

•Press MUTING on the remote again.

•Turn the power off.

•Increase the volume.

To use the headphones

Connect the headphones to the PHONES jack. When the headphones are connected, speaker output is automatically canceled and “SP” does not light up in the display.

When MULTI CHANNEL DECODING indicator lights up

The MULTI CHANNEL DECODING indicator lights up when the receiver is decoding multi channel sources.

However, this indicator does not light up if you select 2CH STEREO mode.

18US

Image 18

Contents Home Theatre System For customers in the United States About This Manual SS-MSP68 SS-CNP68 SA-WMSP68 DVP-NC675PSS-MSP68 SS-CNP68 SA-WMSP76 DVP-NC675P Table of Contents Getting Started Check how to hookup your componentsConnectable components VCROptical digital cord Required cordsAudio cord Video cord Audio/video cordHooking up a DVD player or satellite tuner Connect the audio jacksFor details on the required cords A-E, see Connect the video jacks Satellite tuner TV monitor1b Connecting components with only analog audio jacks Hooking up audio componentsHooking up video components 10USGetting Connecting the antennasConnect the supplied AM loop antenna and FM wire antenna StartedAttaching foot pads Connecting speakersExample of 5.1 channel speaker system configuration 12USSpeaker cords supplied Required cords13US Monaural audio cord supplied14US Connecting the AC power cordPerforming initial setup operations Press EnterSpeaker setup parameters Getting Started 15USListening to the sub woofer Setting up the sub wooferSL SR PL Surround speaker placement 16USPress Test Tone again after adjustment Adjusting the levelTurn Level to adjust the volume Getting Started 17USSelecting the component When Multi Channel Decoding indicator lights upTo use the headphones To mute the soundListening to FM/AM radio Automatic tuningPress Tuning + or Tuning Amplifier Operation 19USPresetting radio stations Presetting radio stationsTuning to preset stations Changing the information in the display Adjusting the brightness of the displayChanging the display Amplifier Operation 21USDTS Lights up when DTS signals are input About the indications in the display22US Enjoying Surround Sound 23US Decoding the input audio signal automaticallyEnjoying higher fidelity sound Press 2CHAbout DCS Digital Cinema Sound Selecting a sound fieldSelecting a sound field for movies 24USTo turn off the surround effect Selecting a sound field for musicAbout Cinema Studio EX modes Enjoying Surround Sound 25USSwitching the audio input mode for digital components Adjusting the Level menuCustomizing sound fields Range COMP. XXX Dynamic range compressor Resetting sound fields to the initial settingsAdvanced Adjustments and Settings 27US EFCT. XXX Effect levelAdjusting the tone Advanced settingsUsing the Customize menu to adjust the receiver Advanced Adjustments and Settings 29US Name Naming preset stations and inputsDual Digital broadcast language selection To index a preset station Naming preset stations and inputsUsing the Sleep Timer To index an inputRecording on a video tape RecordingRecording on an audio tape or MiniDisc Other Operations 31USBefore you use your remote Inserting batteries into the remote32US Operations Using the Remote RM-PP760 33US 34US To reset the remote to factory settings Selecting the command modeTo check the command mode of the remote Operations Using the Remote RM-PP760 35USProgramming the remote To control an MD deck To control a CD playerTo control a DAT deck To control a tape deckTo control a TV To control a VCRTo control a DVD player To control a satellite tuner or cable boxPrecautions Additional Information 39USTroubleshooting 40USAdditional Information 41US Remote controlError message If there is a malfunction, the display shows a messageReference sections for clearing the receiver’s memory SpecificationsIf the problem persist 42US43US SA-WMSP68 Supplied accessories44US SA-WMSP76Page Main unit How to use pages 46List of button locations and reference pages 46USAdditional Information 47US Index