Sansui SLED1953W owner manual TV operation, To select the video input source

Automatic Search

Start

E-POP Demo

Signal Type

Off Cable

TV Location

Store

Starting setup

The Auto Setup menu appears the first time you turn on the TV, and assists you to specify the Air/Cable setting, and program your channels automatically.

IMPORTANT: Make sure that the antenna or cable TV system connection is made!

1 To turn on the TV, press (POWER) (POWER indicator on the front of the unit changes green. It may take approx. 10 seconds for a picture to appear on screen.). The Auto Setup function begins.

Auto Setup

	Press		or	to select “TV Location”, then
2 press			or	to select “Home” or “Store”. This
	product qualifies for ENERGY STAR In Home
	mode default setting.
	NOTE:
	•	This unit has been preset to STORE brightness.
		This setting does not qualify under ENERGY
		STAR. To reduce brightness and energy
		consumption, change setting to ‘HOME’. This
		setting does qualify under ENERGY STAR.
	• The device may not conform to the ENERGY
		STAR standard after Reset is performed or the
		Backlight is adjusted.
	Press		or	to select “E-POP Demo”, then
3 press			or	to select “On” or “Off”.
	On: A TV feature introduction will pop up at the
		bottom of the screen.
4	Off: Turn off the E-POP Demo feature.
	Press		or	to select “Signal Type”, then press
		or	to select “Air” or “Cable”.
	Press		or	to select “Automatic Search”,
5 then press				or ENTER.

		“Auto Setup” will begin. After the Auto Setup
6 is completed, the TV channel appears on the
		screen.
		• Depending on the reception condition, it may
		take up to 30 minutes to complete memorizing
		digital cable channels. Please allow the
		process to complete without interruption.
NOTE:
•	If you press EXIT in the process of “Auto Setup”,
	the Auto Setup stops and changes to the normal
	screen.
•	When you make a menu selection, your changes
	occur immediately.You do not have to press EXIT to
	see your changes.
TV operation
1		To turn on the TV, press	(POWER).
		(POWER indicator on the front of the unit
		changes green. It may take approx. 10 seconds
2		for a picture to appear on screen.)
		Adjust the volume level by pressing VOL + or – .
		The volume level will be indicated on the screen
		by green bars. As the volume level increases, so
		do the number of bars. If the volume decreases,
		the number of green bars also decreases.

3 Set the Signal Type option to the appropriate position (see “Air/Cable selection” on page 18).

4 Press the Direct Channel Selection (0-9, –) buttons to select the channel.

(If you press only channel number, channel selection will be delayed for a few seconds.)

TO SELECT ANALOG CHANNELS

1-9: Press 1-9 as needed. Example, to select channel 2, press 2, then press

ENTER.

10-99: Press the 2 digits in order. Example, to select channel 12, press 1, 2, then press ENTER.

100-135: Press the 3 digits in order. Example, to select channel 120, press 1, 2, 0, then press ENTER.

TO SELECT DIGITAL CHANNELS

Press the first 1-3 digits, then press the – button, followed by the remaining number.

Example, to select channel 15-1, press 1, 5, –, 1, then press ENTER.

• If a channel is selected with only audio content, “Audio only” will be displayed on the screen.

• If a channel is selected with a weak digital signal, “Digital channel signal strength is low” will be displayed on the screen.

The same program may be available on either an analog channel or a digital channel.You may choose to watch either format.

• If a channel is selected to which you have not subscribed, “Digital channel is encrypted” will be displayed on the screen.

VHF/UHF/CABLE CHANNELS

Air		Cable
VHF		VHF
2-13		2-13
UHF	STD/HRC/IRC
14-69	14-36	(A) (W)
	37-59	(AA) (WW)
	60-85	(AAA) (ZZZ)
	86-94	(86) (94)
	95-99	(A-5) (A-1)
	100-135 (100) (135)
	01	(4A)

NOTE:

• If a channel with no broadcast is selected, the sound will automatically be muted.

• It may take a few seconds for a digital channel picture to appear on screen after being selected.

To select the video input source

To view a signal from another device connected to your LCD TV, such as a VCR player, press INPUT SELECT, then press or or corresponding Number buttons (0-4), then press ENTER.You can select TV, Video, Component, HDMI or PC depending on which input jacks you used to connect your devices.

Input Select

0.TV

1.Video

2.Component

3.HDMI

4.PC

[0-4]:Select

ENGLISH

15