Sony SLV-X827MN manual Specifications, System, Inputs and outputs, General, Supplied accessories

Page 52

Specifications

System

Channel coverage

VHF R1 to R12, E2 to E12, NZ1 to NZ9 UHF E21 to E69, R21 to R69

CATV S01 to S05, S1 to S41 RF output signal

UHF channels 21 to 69 Aerial out

75-ohm asymmetrical aerial socket

Inputs and outputs

LINE-1 IN and LINE-2 IN VIDEO IN, phono jack (1 each)

Input signal: 1 Vp-p, 75 ohms, unbalanced, sync negative

AUDIO IN, phono jack (2 each) Input level: 327 mVrms

Input impedance: more than 47 kilohms

LINE OUT

VIDEO OUT, phono jack (1)

Output signal: 1 Vp-p, 75 ohms, unbalanced, sync negative

AUDIO OUT, phono jack (2) Standard output: 327 mVrms Load impedance: 47 kilohms

Output impedance: less than 10 kilohms

52Additional Information

General

Power requirements

110 – 240 V AC, 50/60 Hz Power consumption

22 W Operating temperature

5°C to 40°C

Storage temperature –20°C to 60°C

Dimensions

Approx. 430 × 109 × 308 mm (w/h/d) including projecting parts and controls

Mass

Approx. 4.5 kg

Supplied accessories

Remote commander (1)

R6 (size AA) batteries (2) Aerial cable (1)

Audio/video cable (3-phono to 3-phono) (1)

Design and specifications are subject to change without notice.

SLV-X827MN 3-858-297-11 (1)

Image 52

Contents Video Cassette Recorder SLV-X827MN 3-858-297-11Precautions SafetyInstalling SLV-X827MNTable of contents Unpacking Getting StartedSetting up the remote commander Using the remote commanderInserting the batteries To operate SetControlling other TVs with the remote commander Setting up the remote commanderCode numbers of controllable TVs TipTEAC67 Mains lead To mains Signal flow Aerial cable Connecting the VCRSupplied Additional connections To a TV that has audio/video input jacksTo a stereo system Audio/video cableTuning your TV to the VCR To check to see if the TV tuning is correct To obtain a clear picture from the VCRSelecting a language Before you start…Presetting channels Presetting all receivable channels automaticallyPresetting channels ExecutePresetting channels manually PROG+Press Prog +/- to select the programme position Channel coverage System D/K System B/GDisabling unwanted programme positions If the picture is not clearSetting up CodePress Cursor / twice to highlight Setting up G-CODE for satellite broadcasts Setting up G-CODEChanging/ disabling programme positions Changing programme positionsChanging/disabling programme positions To disable Setting the clock Press Execute to start the clock Basic Operations Playing a tape# Search · P L AY Stop E W Additional tasks Replaying a recently watched sceneTo set the colour system To play an NTSC-recorded tapePlaying a tape To use the time counterHow to connect to use this function OperationRecording TV programmes Prog + RECTo stop recording To check the remaining tape lengthTo watch another TV programme while recording To save a recordingTo record Ntsc colour system programmes Recording TV programmesTips Recording TV Programmes Using G-CODE OperationsRecording TV programmes using G-CODE To record SelectTo use the VCR after setting the timer To record satellite broadcastsSetting the timer manually Daily/weekly recording Playing/searching at various speeds To resume normal playbackAdditional Operations E W · P L a Y Playback options OperationSlow motion Reverse High speed Using the Click Shuttle ringReverse Tip Recording TV programmes using the quick timer To extend the durationChecking Changing/ cancelling timer settings When the timer settings overlap Checking/changing/cancelling timer settingsProgramme Will be Cut off Seconds will be cut off Recording stereo and bilingual programmes Zweiton German stereo systemNicam system To select bilingual sound while recordingSelecting the sound during playback How sound is recorded on a video tapeRecording stereo and bilingual programmes Stereo Bilingual Usually mixed left Right channelsTo stop searching Searching using the index function= / + Adjusting the tracking Adjusting the pictureAbout Adaptive Picture Control APC Menu choices Changing menu optionsMenu option Set this option to How to connect to record on this VCR How to connect to a stereo systemVMC-810MS audio/video cable Not supplied Signal flow Editing with another VCRBefore you start editing Operation when recording on this VCRTo stop editing Troubleshooting Symptoms caused by contaminated video headsRecording Timer recording Others Symptom Remedy Specifications Supplied accessoriesSystem Inputs and outputsIndex to parts and controls Front panelRear panel Index to parts and controlsDisplay window Remote commander SLV-X827MN 3-858-297-11 Index V, W, X, Y