Sylvania LC320SL8 owner manual External Device Connection, Hdmi Connection, HDMI-DVI Connection

Page 9

Cables not included.

Please purchase the necessary cables at your local store.

INTRODUCTION

5External Device Connection

[HDMI Connection]

HDMI (High Definition Multimedia Interface) transports high definition video and multi-channel digital audio through a single cable. It ensures that the content sent from the source to TV is of the highest possible resolution.

rear of this unit

CONNECTION

e.g.)	To HDMI - IN jack
	To HDMI - IN jack
	HDMI cable

HDMI OUT

DVD player with the HDMI output jack

Note:

•This unit accepts 480i / 480p / 720p / 1080i video signals, and 32kHz / 44.1kHz / 48kHz audio signals.

•This unit accepts only 2 channel audio signal (LPCM).

•You need to select “PCM” for the digital audio output of the device connected or the HDMI audio setting. There may be no audio output if you select “Bitstream”, etc.

•This TV only accepts signals compliant with EIA861.

[HDMI-DVI Connection]

If your video device has a DVI output jack, connect using a HDMI-DVI conversion cable.

INITIAL SETTING WATCHING TV OPTIONAL SETTING

e.g.)

Cable box or satellite box with the DVI output jack

rear of this unit

HDMI-DVI	To HDMI - IN jack
conversion cable

DVI OUT

AUDIO OUT

L R

To AUDIO IN jacks

TROUBLESHOOTING INFORMATION

RCA audio cable

Note:

•This unit accepts 480i / 480p / 720p / 1080i video signals.

•An HDMI-DVI conversion cable requires a separate audio cable connection as well.

•Audio signals are converted from digital to analog for this connection.

•DVI does not display 480i image that is not compliant with EIA/CEA-861/861B.

9

EN

Image 9

Contents LC320SL8 To Receive DIGITAL/ANALOG SIGNAL, YOU Must Connect AntennaImportant note is located on the rear of the cabinet IntroductionRADIO-TV Interference PrecautionsSymbols Used in this Manual Supplied AccessoriesRemote control LocationFeatures ContentsDTV/TV/CATV Installing the Batteries Remote Control FunctionRear Panel Control PanelBasic Connection ConnectionAntenna Cable Connection Connection to Cable Box or Satellite BoxExternal Device Connection Hdmi ConnectionHDMI-DVI Connection Video Cable Connection Component Video Cable ConnectionVideo Connection Audio Output Connection DigitalAnalog Initial Setup Initial SettingMake sure if the unit is connected to antenna or cable Scanning and memorizing of channels start automaticallyAuto Channel Scan Main MenuPress Setup to exit Language SelectionLanguage 5Volume Adjustment Watching TVChannel Selection Switching Each Mode Still ModeYou can freeze the image shown on the TV screen To use the Hdmi in jack on the unit, select HdmiStereo Switching Audio ModeSAP MonoPress Info Screen InformationBroadcasting Information Day of MemoriesiTV Screen Display Mode Sleep Timer Press Sleep to set the sleep timerTo Cancel the Sleep Timer Optional Setting Channel List5Manual Register Antenna Antenna ConfirmationPicture Adjustment Closed Caption DTV Closed Caption DTV CCUse Cursor K/L to select DTV CC, then press CC Style Font StyleFont Size Font Opacity Font ColorBack Color Back OpacityChipip Enter password See the following description for setting each itemChip Use Cursor K/L to select V-chip, then pressUse Cursor K/L to select Mpaa Rating, then press Enter Press Setup to exitView and Block To Set the Sub RatingsChipip Enter password Confirm password Use Cursor K/L to select New Password, then press EnterHdmi Audio You can set the method of sound input for the Hdmi in jackUse Cursor K/L to select Hdmi Audio, then press Troubleshooting Guide TroubleshootingRefer to IR Signal Check on Check the batteries of the remote controlInterrupt the remote control signal of this unit Delayed behind the dialogueInformation MaintenanceGlossary AtscElectrical Specification General SpecificationsOther Specifications Cable Channel DesignationsLimited Warranty