Sylvania LC320SL8 owner manual Watching TV, Channel Selection, 5Volume Adjustment

Page 15

WATCHING TV

5Channel Selection

Select channels by pressing [CH K/L] or [the Number buttons].

To select the memorized channels, use [CH K/L] or [the Number buttons].

To select the non-memorized channels use [the Number buttons].

To Use [the Number buttons]

TV

- When selecting analog channel 12

DTV

-When selecting digital channel 12-1

Be sure to press [–]before entering the minor channel number.

Press [CH RETURN] to return to the previously viewed channel.

About digital TV broadcasting:

With its high definition broadcast, digital broadcasting far surpasses analog broadcasting in both its picture and sound quality.

What is the minor channel?

By using high compression technology, digital broadcasting offers a service that enables multiple signals to send simultaneously.

Therefore, you can select more than one program per major channel since digital broadcasting technology distinguishes between multiple channels broadcast by a single network.

NTSC (analog mode) [Air Time] ATSC (digital mode)

 

18:00

 

 

 

CH4

No signal

No signal

 

18:30

CH4

 

 

 

 

CH4

(high definition TV)

19:00

 

 

 

CH4

CH4-1

No signal

 

19:30

 

 

 

CH4

No signal

CH4-2

 

20:00

 

 

 

CH4

CH4-1

CH4-2

 

20:30

 

 

 

major channel

minor channel

: change automatically

: change manually by using [CH K/ L]

Note:

“No Signal” will appear on the TV screen after the minor channel broadcast is over.

5Volume Adjustment

INTRODUCTION

 

This section describes how to adjust the volume. The mute function, which

 

turns the sound off and on, is also described.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

CONNECTION

Use [VOL. X/Y] to adjust the audio volume.

 

 

Volume 20

 

 

 

 

 

 

 

 

 

• The volume bar will be displayed at the bottom of

 

 

the TV screen when adjusting the volume.

INITIAL

• The volume bar display will automatically disappear

 

in a few seconds.

SETTING

Press [MUTE] to turn off and on the sound.

 

 

 

 

 

 

 

 

 

 

Mute

 

 

 

 

 

 

 

 

 

WATCHINGTV

• “Mute” is displayed on the TV screen for a few

 

seconds.

 

Press [MUTE] again or [VOL. X/Y] to recover the

 

original volume.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

OPTIONAL SETTING

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

TROUBLESHOOTING

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

INFORMATION

 

 

 

 

 

 

 

 

15

EN

Image 15
Contents LC320SL8 To Receive DIGITAL/ANALOG SIGNAL, YOU Must Connect AntennaImportant note is located on the rear of the cabinet IntroductionRADIO-TV Interference PrecautionsLocation Supplied AccessoriesSymbols Used in this Manual Remote controlFeatures ContentsDTV/TV/CATV Installing the Batteries Remote Control FunctionRear Panel Control PanelConnection to Cable Box or Satellite Box ConnectionBasic Connection Antenna Cable ConnectionExternal Device Connection Hdmi ConnectionHDMI-DVI Connection Video Cable Connection Component Video Cable ConnectionVideo Connection Audio Output Connection DigitalAnalog Scanning and memorizing of channels start automatically Initial SettingInitial Setup Make sure if the unit is connected to antenna or cableAuto Channel Scan Main MenuPress Setup to exit Language SelectionLanguage 5Volume Adjustment Watching TVChannel Selection To use the Hdmi in jack on the unit, select Hdmi Still ModeSwitching Each Mode You can freeze the image shown on the TV screenMono Switching Audio ModeStereo SAPDay of Memoriesi Screen InformationPress Info Broadcasting InformationTV Screen Display Mode Sleep Timer Press Sleep to set the sleep timerTo Cancel the Sleep Timer Optional Setting Channel List5Manual Register Antenna Antenna ConfirmationPicture Adjustment Closed Caption DTV Closed Caption DTV CCUse Cursor K/L to select DTV CC, then press CC Style Font StyleFont Size Back Opacity Font ColorFont Opacity Back ColorUse Cursor K/L to select V-chip, then press See the following description for setting each itemChipip Enter password ChipTo Set the Sub Ratings Press Setup to exitUse Cursor K/L to select Mpaa Rating, then press Enter View and BlockChipip Enter password Confirm password Use Cursor K/L to select New Password, then press EnterHdmi Audio You can set the method of sound input for the Hdmi in jackUse Cursor K/L to select Hdmi Audio, then press Troubleshooting Guide TroubleshootingDelayed behind the dialogue Check the batteries of the remote controlRefer to IR Signal Check on Interrupt the remote control signal of this unitAtsc MaintenanceInformation GlossaryCable Channel Designations General SpecificationsElectrical Specification Other SpecificationsLimited Warranty