Canon LV-X4 owner manual Installation, Positioning the Projector, Adjustable Feet

Page 15

Installation

Positioning the Projector

This projector is designed to project on a flat projection surface and can be focused from 3.3’(1.0m) - 25.3’(7.7m). Refer to the figure and the table below for the screen size and the distance between the projector and the screen.

A : B = 9 : 1

25.3’ (7,7m)

300”

16,1’ (4,9m)

12.5’ (3.8m)

Max. Zoom

(Inch Diagonal)

8,2’ (2,5m)

3.3’ (1.0m)

100”

40”62”

150”

95”

190”

122”

190”

Min. Zoom

A

(Center)

B

Installation

Screen Size

 

40”

 

100”

150”

190”

300”

(W x H) mm

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

813 x 610

 

2032 x 1524

3048 x 2286

3861 x 2896

6096 x 4572

4 : 3 aspect ratio

 

 

 

 

 

 

 

 

 

 

Zoom (min)

 

5.2' (1.6m)

 

13.1' (4.0m)

19.7' (6.0m)

25.3' (7.7m)

–––––

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Zoom (max)

 

3.3' (1.0m)

 

8.2' (2.5m)

12.5' (3.8m)

16.1' (4.9m)

25.3' (7.7m)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Note:

The brightness in a room has a great influence on picture quality. It is recommended to limit ambient lighting in order to obtain the best image.

The values shown above are approximate and may vary from the actual size.

Adjustable Feet

Projection angle can be adjusted up to 11.9 degrees with the adjustable feet.

1

Lift the front of the projector and pull upward the feet lock

 

latches on both sides of the projector.

2

Release the feet lock latches to lock the adjustable feet and

 

rotate the adjustable feet to adjust the position and tilt.

3

To retract the adjustable feet, lift the front of the projector

 

and pull and undo the feet lock latches.

Keystone distortion of the projected image can be adjusted by menu operation. (p24, 41)

Feet Lock Latches

Adjustable Feet

15

Image 15
Contents LV-X4 Wide Zoom Lens User’s Logo Features and DesignTable of Contents Risk of Electric Shock Do not Open To the OwnerSafety Instructions Installing the Projector in Proper Position Air CirculationMoving the Projector Federal Communication Commission Notice ComplianceBottom Part Names and FunctionsVideo Service PortRGB IN-1/ Component AudioLV-X4 Top ControlSignal Emission indicator Remote Control UnitPointer Function Wireless Mouse OperationOperating Range Remote Control CodeRemote Control Battery Installation Installation Adjustable FeetPositioning the Projector Connecting the AC Power Cord For the U.S.A. and Canada For Continental Europe200 240 V AC Cables used for connection Connecting to a ComputerCable Connecting to Video EquipmentConnecting to Component Video Equipment Enter a PIN code What is PIN code?Basic Operation Turning On the ProjectorTurning Off the Projector Top Control How to Operate the On-Screen MenuRemote Control Unit On-Screen MenuImage Select Menu Menu BarZoom and Focus Adjustment Keystone AdjustmentPicture Freeze Function No Show Function Timer FunctionSound Adjustment VolumeInput Source Selection Computer InputPC System Menu Computer System SelectionAuto ModeAuto PC Adj Auto PC AdjustmentPC Adjust Menu To store adjustment parametersManual PC Adjustment Display area H ResetMode free Display areaBlackboardGreen Image Level SelectionStandard High contrastImage Level Adjustment Screen Size Adjustment Video Input Input Source Selection Video, S-VideoInput button Video Computer Video button Input button Computer Video Computer button Input Source Selection Component, RGB Scart 21-PinAV System Menu Component Video System SelectionAuto AV System Menu Video or S-VideoImage button Standard Cinema BlackboardGreen Custom CinemaTint ColorFilm ProgressiveProvides image at a normal video aspect ratio of 4 Setting SettingCapture Enter a Logo PIN codeChange the Logo PIN code LogoTerminal Power managementCeiling RearLamp mode Remote controlPointer PIN code lock Key lockPIN code lock Key lockTo Change the PIN code To Change the PIN code lock settingLamp counter reset Factory defaultMaintenance and Cleaning Projector is shut down and the Warning indicator lights redThen check the matters below Attaching the Lens Cover Cleaning the Air FiltersCleaning the Projector Cabinet Cleaning the Projection LensReset the Lamp replace counter Lamp ReplacementLamp Replace Counter When the lamp replace counter is reset, the LampAppendix TroubleshootingAppendix Remote Control unit does not work. Check the batteriesProjector Condition Indicators and Projector ConditionMenu Tree Image Adjust System SettingResolution Compatible Computer SpecificationsTechnical Specifications Accessories This cable is used for RGB Scart 21-Pin Configurations of TerminalsUSB Connector Series B Optional PartsWhile the projector is locked with the PIN code Page Page Canon U.S.A., INC