Canon LV-X4 owner manual Ceiling, Rear, Terminal, Power management, On start

Page 43

Setting

Ceiling

When this function is “On,” the picture is top/bottom and left/right reversed. This function is used to project the image from a ceiling mounting the projector.

Rear

When this function is “On,” the picture is left/right reversed. This function is used to project the image to a rear projection screen.

Terminal

The RGB IN-2/RGB OUT terminal on the back of the projector is switchable for computer input or monitor output. (See page 9) Select Computer 2 or Monitor Out with the Point Left/Right button.

RGB IN-2 . . . . . . .computer input

RGB Out . . . . . . . .monitor out

Terminal item is not available when selecting Computer 2 to the input source. Change the input source to the others (Computer1 or Video) so that the Terminal item will be available. (p26, 34, 35)

Power management

For reducing power consumption as well as maintaining the lamp life, the Power Management function turns off the projection lamp when the input signal is interrupted and no button is pressed for 30 seconds or more.

If the input signal is interrupted and no button is pressed for 30 seconds or more, the timer display with the message "No signal" appears on the screen. The count-down of the set time will get started. The count-down time can be set between 1 and 30 minutes.

When the count-down time has been elapsed, the lamp will be turned off to cool itself down. The POWER indicator is blinking red during this cooling-off period. The next operation depends on the setting as follows :

Ready . . . . . .When the lamp has been fully cooled down, the POWER indicator changes to green blinking. In this condition, the projection lamp will be turned on if the input signal is reconnected or any button on the top control or remote control unit is pressed.

Shutdown . . .When the lamp has been fully cooled down, the power will be turned off.

Off . . . . . . . . .The Power Management function is canceled.

On start

When this function is “On,” the projector is automatically turned on just by connecting the AC power cord to a wall outlet.

✔Note:

Be sure to turn the projector off properly (see “Turning Off the Projector” on page 21). If the projector is turned off in the wrong steps, the On start function does not operate properly.

Ceiling

Setting

Rear

Power management

Time left until Lamp off

Press the SET button at Power management and this box appears. Choose one of three settings with the Point 7 8 button, and go to the timer with the Point ed button and set time with the Point 7 8 button.

43

Page 42 Page 44
Image 43
Page 42 Page 44
Contents LV-X4 Wide Zoom Lens User’s Logo Features and DesignTable of Contents Risk of Electric Shock Do not Open To the OwnerSafety Instructions Air Circulation Installing the Projector in Proper PositionMoving the Projector Federal Communication Commission Notice ComplianceBottom Part Names and FunctionsVideo Service PortRGB IN-1/ Component AudioLV-X4 Top ControlSignal Emission indicator Remote Control UnitPointer Function Wireless Mouse OperationOperating Range Remote Control CodeRemote Control Battery Installation Adjustable Feet InstallationPositioning the Projector For the U.S.A. and Canada For Continental Europe Connecting the AC Power Cord200 240 V AC Cables used for connection Connecting to a ComputerCable Connecting to Video EquipmentConnecting to Component Video Equipment Enter a PIN code What is PIN code?Basic Operation Turning On the ProjectorTurning Off the Projector Top Control How to Operate the On-Screen MenuRemote Control Unit On-Screen MenuImage Select Menu Menu BarKeystone Adjustment Zoom and Focus AdjustmentPicture Freeze Function No Show Function Timer FunctionSound Adjustment VolumeInput Source Selection Computer InputPC System Menu Computer System SelectionAuto ModeAuto PC Adj Auto PC AdjustmentPC Adjust Menu To store adjustment parametersManual PC Adjustment Display area H ResetMode free Display areaBlackboardGreen Image Level SelectionStandard High contrastImage Level Adjustment Screen Size Adjustment Input Source Selection Video, S-Video Video InputInput button Video Computer Video button Input button Computer Video Computer button Input Source Selection Component, RGB Scart 21-PinAV System Menu Component Video System SelectionAuto AV System Menu Video or S-VideoImage button Standard Cinema BlackboardGreen Custom CinemaTint ColorFilm ProgressiveProvides image at a normal video aspect ratio of 4 Setting SettingCapture Enter a Logo PIN codeChange the Logo PIN code LogoTerminal Power managementCeiling RearRemote control Lamp modePointer PIN code lock Key lockPIN code lock Key lockTo Change the PIN code To Change the PIN code lock settingLamp counter reset Factory defaultProjector is shut down and the Warning indicator lights red Maintenance and CleaningThen check the matters below Attaching the Lens Cover Cleaning the Air FiltersCleaning the Projector Cabinet Cleaning the Projection LensReset the Lamp replace counter Lamp ReplacementLamp Replace Counter When the lamp replace counter is reset, the LampAppendix TroubleshootingAppendix Remote Control unit does not work. Check the batteriesProjector Condition Indicators and Projector ConditionMenu Tree Image Adjust System SettingResolution Compatible Computer SpecificationsTechnical Specifications Accessories This cable is used for RGB Scart 21-Pin Configurations of TerminalsUSB Connector Series B Optional PartsWhile the projector is locked with the PIN code Page Page Canon U.S.A., INC
Top Page Image Contents