Canon LV-X4 owner manual Enter a Logo PIN code, Change the Logo PIN code, Capture

Page 42

Setting

Enter a Logo PIN code

Select a number by pressing the Point 7 8 button and fix the number with the SET button. The number will change to "". If you fixed a wrong number, move the pointer to "Set" or "Clear" once by pressing the Point d button, then return to "Logo PIN code". Enter the correct number again.

Repeat this step to complete entering a four-digit number.

When the four-digit number is fixed, the pointer will automatically move to "Set". Press the SET button so that you can change the Logo PIN code lock setting.

If you entered a wrong Logo PIN Code, "Logo PIN code" and the number (✳✳✳✳) will turn red and disappear. Enter a correct Logo PIN code all over again.

Change the Logo PIN code

Logo PIN code can be changed to your desired four-digit number. Select "Logo PIN code change" with the Point d button and press the SET button. Set a new Logo PIN code.

Be sure to note the new Logo PIN code and keep it at hand.

Note:

If you forget your Logo PIN code and unable to change it, the Logo P IN code can be reset to the factory default setting (4321) according to the following procedures. When you reset the Logo PIN code, the PIN code will be reset, as well.

1.Disconnect the AC Power Cord from the AC outlet.

2.As pressing the SET button on the projector, connect the AC Power Cord into an AC outlet again. Keep pressing the SET button until the POWER indicator lights.

The Logo PIN code will be returned to the factory default setting while the Logo PIN code lock state will remain the same as previous set state.

Logo

This function decides what to be displayed on the starting-up display as follows:

User . . . . . .the image you captured Default . . . .the factory-set logo Off . . . . . . .count-down only

Capture

This function enables you to capture the image being projected and use it for a starting-up display or interval of presentations. After capturing the projected image, go to the Logo function and set it to “User”. Then the captured image can be displayed when turning on the projector next time or pressing the NO SHOW button. (p25)

To capture the image, select [Yes]. To cancel the Capture function, select [No].

Note:

Before capturing an image, select Standard in the Image Select Menu to capture a proper image. (See page 31,37.)

A signal from a computer can be captured up to XGA(1024 x 768). A signal from video equipment can be captured except for 720p, 1035i, and 1080i.

When capturing the image that has been adjusted by the Keystone function, the adjustment data is automatically reset and the projector captures an image without keystone adjustment.

When the Logo PIN code lock function is On, the Logo and Capture menu cannot be selected.

Logo PIN code lock Dialog Box

Pointer

Quit

After a correct Logo PIN code is entered, the following dialog box will appear.

Select On/OFF by pressing the Point 7 8 button or change the Logo PIN code.

Capture

Select [Yes] to capture the projected image.

Select [Yes] to stop capturing.

42

Image 42
Contents LV-X4 Features and Design Wide Zoom Lens User’s LogoTable of Contents To the Owner Risk of Electric Shock Do not OpenSafety Instructions Installing the Projector in Proper Position Air CirculationMoving the Projector Compliance Federal Communication Commission NoticePart Names and Functions BottomAudio Service PortRGB IN-1/ Component VideoTop Control LV-X4Remote Control Unit Signal Emission indicatorWireless Mouse Operation Pointer FunctionRemote Control Code Operating RangeRemote Control Battery Installation Installation Adjustable FeetPositioning the Projector Connecting the AC Power Cord For the U.S.A. and Canada For Continental Europe200 240 V AC Connecting to a Computer Cables used for connectionConnecting to Video Equipment CableConnecting to Component Video Equipment Turning On the Projector What is PIN code?Basic Operation Enter a PIN codeTurning Off the Projector On-Screen Menu How to Operate the On-Screen MenuRemote Control Unit Top ControlMenu Bar Image Select MenuZoom and Focus Adjustment Keystone AdjustmentPicture Freeze Function Volume Timer FunctionSound Adjustment No Show FunctionComputer Input Input Source SelectionMode Computer System SelectionAuto PC System MenuTo store adjustment parameters Auto PC AdjustmentPC Adjust Menu Auto PC AdjManual PC Adjustment Display area ResetMode free Display area HHigh contrast Image Level SelectionStandard BlackboardGreenImage Level Adjustment Screen Size Adjustment Video Input Input Source Selection Video, S-VideoInput button Video Computer Video button Input Source Selection Component, RGB Scart 21-Pin Input button Computer Video Computer buttonAV System Menu Video or S-Video Video System SelectionAuto AV System Menu ComponentCinema Image button Standard Cinema BlackboardGreen CustomColor TintProgressive FilmProvides image at a normal video aspect ratio of 4 Setting SettingLogo Enter a Logo PIN codeChange the Logo PIN code CaptureRear Power managementCeiling TerminalLamp mode Remote controlPointer Key lock Key lockPIN code lock PIN code lockFactory default To Change the PIN code lock settingLamp counter reset To Change the PIN codeMaintenance and Cleaning Projector is shut down and the Warning indicator lights redThen check the matters below Cleaning the Air Filters Attaching the Lens CoverCleaning the Projection Lens Cleaning the Projector CabinetLamp Replacement Reset the Lamp replace counterWhen the lamp replace counter is reset, the Lamp Lamp Replace CounterTroubleshooting AppendixRemote Control unit does not work. Check the batteries AppendixIndicators and Projector Condition Projector ConditionMenu Tree System Setting Image AdjustCompatible Computer Specifications ResolutionTechnical Specifications Accessories Optional Parts Configurations of TerminalsUSB Connector Series B This cable is used for RGB Scart 21-PinWhile the projector is locked with the PIN code Page Page Canon U.S.A., INC